Korenix JetNet 5428G-20SFP Series User manual

JetNet 5428G-20SFP Series Industrial 8FE+16SFP+4G Gigabit Managed Switch
Quick Installation Guide V1.0
e JetNet 5428G-20SFP Series is a 19-inch Gigabit Industrial switch, equipped with 8 100
Base-TX ports, 16 100 SFP, and 4 100/1000 RJ-45/SFP combo ports. JetNet 5428G-20SFP is
a special design for industrial control rooms where high-port density and performance are
required.
Dimension
JetNet 5428G-20SFP Industrial 8FE+16SFP+4G Gigabit Managed Ethernet Switch dimension
(H x W x D) is 43.6mm (H) x 431mm (W) x 375mm (D).
Front-Panel Components
e front panel includes RJ-45 based RS-232 console port, USB port, System & port LEDs,
Gigabit Ethernet port interfaces and Gigabit combo Port interfaces.
LED Indicators
Back-Panel Components
e back panel of the JetNet 5428G-20SFP-AC consists of 1 AC power input and 1 relay
output. e back panel of the JetNet 5428G-20SFP-2DC consists of 2 DC power inputs and
1 relay output.
JetNet 5428G-20SFP-AC:
JetNet 5428G-20SFP-2DC:
Package Check List
 e Rack Mount Managed Ethernet Switch
 Console cable
 Rack Mount kit
 Power Cord (Depend on Country, JetNet 5428G-20SFP-2DC no Power Cord)
 QIG
Overview
Interface Introduction
A Beijer Electronics Group Company
Installation
Mount the Switch to 19’’ rack
1. Attach the brackets to the device by using the
screws provided in the Rack Mount kit.
2. Mount the device in the 19’’ rack by using four
rack-mounting screws provided by the rack
manufacturer.
3. When installing multiple switches, mount them in
the rack one below the other.
Power the unit and connect to network Cable
Wiring Power Inputs
AC Power Input: connect the attached power cord to the AC power input connector, the
available AC power input is range from 90-264VAC.
DC Power Input: the suggested power input is 24VDC or 48VDC, the available range is
from 18-75VDC. Follow below steps to wire JetNet 5428G-20SFP-2DC redundant DC
power inputs.
1. Insert positive and negative wires into V+ and V- contacts respectively of the terminal
block connector.
2. Tighten the wire-clamp screws to prevent DC wires from being loosened.
3. DC1 and DC2 support polarity reverse protection functions.
Wiring Digital Output
JetNet 5428G-20SFP provides 1 digital output, also known as relay output. e relay
contacts are energized (open) for normal operation and will close for fault conditions. e
fault conditions include power failure, Ethernet port link break or other pre-dened events
which can be congured in JetNet 5428G-20SFP UI.
Wiring Earth Ground
To ensure the system will not be damaged by noise or any electrical shock, we suggest you to
make exact connection with JetNet 5428G-20SFP with earth ground.
For AC input, the 3 pin include V+, V- and GND. e GND pin must be connected to the
earth ground.
For DC input, loosen the earth ground screw by screw drive; then tighten the screw after
earth ground wire is connected.
Note: Check if the rack environment temperature conforms to the specied operating
temperature range. Do not place any equipment on top of the switch and please properly
grounded.
8 100Base-TX, 16 100 SFP, 4 100/1000 RJ-45/SFP combo ports, Ind.
Gigabit Managed Ethernet Switch,-40~75°C, AC power
8 100Base-TX, 16 100 SFP, 4 100/1000 RJ-45/SFP combo ports, Ind.
Gigabit Managed Ethernet Switch,-40~75°C, dual DC power
Model Name Description
JetNet 5428G-20SFP-2DC
JetNet 5428G-20SFP-AC
1 AC power input and 1 relay output.
2 DC power inputs and 1 relay output.
JetNet 5428G-20SFP-AC
JetNet 5428G-20SFP-2DC
Model Name Back-Panel Components
LED
C
olor Function
Alarm Red Power failure, port failure, ping failure,
login failure, RSR topology change
R.S.
Lit Green MSR in normal state
Lit Yellow MSR in abnormal state
Not Lit MSR function not active
Flashes Green Incorrect configuration of MSR, ex. ring
not connected to ring port
Flashes Yellow The break has been detected to be
local to one of the ports
PWR Green Power (AC/DC) on
Sys Green System on
1-8 10/100
Copper
Lit Green/Flashes Green Link/Activity
Lit Yellow Duplex
9-24 SFP Lit Green/Flashes Green Link/Activity
G25-G28
Giga SFP Lit Green/Flashes Green Link/Activity
G25-G28
Giga Copper
Lit Green/Flashes Green Link/Activity
Yellow On/Off 1000Mbps/(10/100Mbps)
2 4 6 8
1 3 5 7
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28 G26 G28
G27 LNK/ACT
SPEED
G25
LNK/ACT
Duplex
Console
USB
PWR
1
2
3
Alarm
Sys
R.S.
Industrial 24+4G Gigabit
Managed Ethernet Switch
10
9
12
11
14
13
16
15
18
17
20
19
22
21
24
23
26
25
28
27
2 4
1 3
LNK/ACT
Duplex
Console
USB
PWR
1
2
3
Alarm
Sys
R.S.
25
26
27
28 G26 G28
G27 LNK/ACT
SPEED
G25
26
25
28
27
--<-
1A@24V
--<-
PWR1
100-240VAC, 50-60Hz,0.6A
18-75VDC,1.5A
PWR2 PWR3
--<-
1A@24V
--<-
PWR1
100-240VAC, 50-60Hz,0.6A
18-75VDC,1.5A
PWR2 PWR3

Wiring Fast Ethernet Ports
JetNet 5428G-20SFP includes 8 RJ-45 Fast Ethernet ports. e Fast Ethernet ports support
100Base-TX, full or half duplex modes. All the Ethernet ports will auto-detect the signal from
connected devices to negotiate the link speed and duplex mode. Auto MDI/MDIX allows
users to connect another switch, hub or workstation without changing straight through or
crossover cables.
Note that crossover cables simply cross-connect the transmit lines at each end to the received
lines at the opposite end.
Wiring Fiber Ports
e SFP ports accept standard MINI GBIC SFP transceiver. But, to ensure system reliability,
Korenix recommends using the Korenix certicated SFP Transceiver. e web UI will show
unknown vendor type when choosing the SFP which is not certicated by Korenix. e
certicated SFP transceiver includes 100Base-FX single/multi mode, 100Base-FX
BIDI/WDM, distance range from 550m to 80KM.
e way to connect the SFP transceiver is to plug in SFP ber transceiver st. Cross-connect
the transmit channel at each end to the receive channel at the opposite end as illustrated in the
gure below. e SPF cage is 2x1 design, check the direction/angle of the ber transceiver and
ber cable when inserted.
Note: is is a Class 1 Laser/LED product. Don’t look into the Laser/LED Beam.
Device Management
Before you attempt to use the embedded web interface to manage switch operation, verify that
your JetNet 5428G-20SFP is properly installed on your network and that every PC on this
network can access the switch via the web browser.
1. Launch the web browser on the PC.
2. Type http://JetNet 5428G-20SFP_IP_Address (e default IP address is 192.168.10.1.)
then press Enter.
3. e login screen will appear next. Key in the user name and the password. e default user
name and password is admin/admin.
4. Click OK, and then the Home page of the web-based management interface will appear.
5. At the left column of the web management interface is the software function. e right
column lists the available settings. e top column indicates the front panel and shows the
link status of each interface.
Wiring Gigabit Combo Ports
JetNet 5428G-20SFP series equips 4 Gigabit SFP ports combo with Gigabit Ethernet RJ-45
ports. e speed of the SFP port supports 100MB and 1000MB Full Duplex. e available
Gigabit SFP supports Gigabit Single-mode, Multi-mode, BIDI/WDM single-mode SFP
transceivers.
While the SFP transceiver is plugged, the ber port has higher priority than copper port and
moved to the ber mode automatically.
Wiring RS-232 Console Cable
Korenix JetNet 5428G-20SFP attaches one RS-232 cable in the box. Connect the DB-9
connector to the COM port of your PC, open terminal tool and set up serial settings to
115200, N,8,1. (Baud Rate: 115200/ Parity: None / Data Bit: 8 / Stop Bit: 1) en you can
access CLI interface by console cable.
Note: If you lost the cable, please contact with your sales or follow the pin assignment to buy a
new one.
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Granted Invention: I 459757
Utility Model: M 339841
Utility Model: M 339840
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
Tel:[phone]
Fax:[phone]
Business service:[email protected]
Customer service:[email protected]
www.korenix.com
CPQ000N5428002
Preparation for console management
Attach the RS-232 DB9 connector to your PC’s COM port. Connect the RJ-45 based RS-232
connector to the console port of the JetNet 5428G-20SFP.
1. Go to Start
 Program  Accessories  Communication  Hyper Terminal
2. Give a name to the new console connection.
3. Choose the COM name, and select the correct serial settings. e serial settings of the
JetNet 5428G-20SFP are as below:
Baud Rate: 115200/ Parity: None / Data Bit: 8 / Stop Bit: 1
4. After connected, you can see Switch login request. Type the username and password then
you can login. e default username is “admin”, password is “admin”.
5. Follow the manual to congure the software features.
Preparation for Telnet management
Go to Start  Program  Accessories  DOS Prompt, Type Telnet 192.168.10.1 (Default IP
Address) then press Enter.
Device Management
5 Years Warranty
Each of Korenix’s product is designed, produced, and tested with high industrial standard.
Korenix warrants that the product(s) shall be free from defects in materials and
workmanship for a period of ve (5) years from the date of delivery provided that the
product was properly installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted product are
caused by damage resulting from force measure (such as oods, re, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment (RoHS Directives & RoHS
2.0)
Korenix Customer Service
KoreCARE is Korenix Technology’s global service center, where our professional stas are
ready to answer your questions at any time.
Email address of Korenix Global Service Center: [email protected]
For more information and documents download please visit our website:
http://www.korenix.com/page/doc/index.aspx
Support