Korenix JetNet 3210GP-2C User manual

Korenix JetNet 3210GP-2C
Industrial Power over Ethernet GbE Switch
User’s Manual
Version: 1.0
www.korenix.com

Korenix
JetNet 3210GP-2C
1
Korenix JetNet 3210GP-2C
Industrial Power over Ethernet GbE Switch
User’s Manual
Copyright Notice
Copyright © 2015 Korenix Technology Co., Ltd.
All rights reserved.
Reproduction in any form or by any means without permission is prohibited.

Korenix
JetNet 3210GP-2C
2
Index
Index...............................................................................................................................2
1. Introduction ...............................................................................................................3
1.1 Overview ..........................................................................................................4
1.2 Product Features..............................................................................................5
2. Hardware Installation.................................................................................................6
2.1 Hardware Introduction ............................................................................................6
Dimensions.....................................................................................................6
Front Panel.....................................................................................................7
Bottom View ..................................................................................................8
LED Indicators.................................................................................................8
2.2 Wiring the Power Inputs..................................................................................9
2.3 Wiring the Relay Output ................................................................................10
2.4 Wiring Earth Ground......................................................................................10
2.6 Wiring the Ethernet Ports..............................................................................11
2.7 Wiring the Fiber Ports....................................................................................12
2.8 Connecting Powered Device (PD) ..................................................................13
2.9 DIN-Rail Mounting Installation.......................................................................13
3. Appendix ..................................................................................................................14
3.1 Product Specification ...............................................................................14
3.2 Revision History..............................................................................................16

Korenix
JetNet 3210GP-2C
3
1. Introduction
Korenix JetNet 3210GP-2C is a power over Ethernet switch that is specially designed
for industrial or commercial applications. The following topics are covered in this
chapter:
1.1 Overview
1.2 Product Features

Korenix
JetNet 3210GP-2C
4
1.1 Overview
JetNet 3210GP-2C, Industrial Power over Ethernet (PoE) GbE Switches, are
designed with 8 Gigabit Ethernet PoE ports and 2 Gigabit SFP/Gigabit combo uplink
ports to ensure high-bandwidth uplink connection for wide PoE markets. JetNet
3210GP-2C which is compliant with IEEE 802.3af/at PoE standard to deliver
maximum 30Watts per 8 ports. For JetNet 3210GP-2C model, it integrates with
power boost technology- Input DC 12~54V boosting to 54VDC built-in power
booster which is the best solution for the vehicle PoE applications with standard
DC 54V power supply unavailable. It also combines hot-swappable SFP fiber
transceiver interfaces which can meet different specifications of fiber cable for
extending transmission distance.
To ensure the high quality of video data transmission, JetNet 3210GP-2C not only
provide Gigabit bandwidth uplink for large image traffic, but also support QoS to
adjust the priority of data transfer. With the feature of Fault Relay, JetNet
3210GP-2C could automatically warn administrator if any abnormal situation
happens. The compact size with IP-31 rigid aluminum case allows JetNet
3210GP-2C to be reliably operated in -40~75℃extreme environment.

Korenix
JetNet 3210GP-2C
5
1.2 Product Features
Korenix JetNet 3210GP-2C have the following features:
8 Gigabit Base TX ports and 2 Gigabit RJ-45/ SFP combo ports
SFP ports support 100/1000 Mbps
IEEE 802.3af 15.4W / IEEE 802.3at 30W High Power PoE
Total PoE Budget 240W @ 75oC ambient temperature
IEEE 802.1p Class of Service (CoS) for packet forwarding precedence
10K bytes Jumbo Frame for large file transmission
Broadcast storm packet filtering
Dual DC Power input 12~56V
Embedded DC 54V Booster
Traffic Standard: E-mark E13
-40~75℃operating temperature

Korenix
JetNet 3210GP-2C
6
2. Hardware Installation
2.1 Hardware Introduction
Dimensions
JetNet 3210GP-2C dimensions: 135(H) x 79.56(W) x132(D) (without Din-rail clip)

Korenix
JetNet 3210GP-2C
7
Front Panel
JetNet 3210GP-2C includes system power LED x1, alarm relay LED x1, PoE LED x8, 16
LEDs for RJ-45 port operating status, and 4 LEDs for SFP fiber port status.
JetNet 3210GP-2C
Power LED
Alarm Relay LED
PoE Indicators
LED for RJ-45 port
RJ-45 ports for
10/100/1000M
bps
LED for SFP

Korenix
JetNet 3210GP-2C
8
Bottom View
The bottom side of the JetNet 3210GP-2C includes one 6-pin removable terminal
block connector (with 2 power input & 1 relay alarm output) . There is also an earth
ground screw to prevent interference.
LED Indicators
The following table describes the function of each LED indicator.
LED
Status
Description
PWR1
Green
DC-IN Power
Off
No Power in DC-IN
PWR2
Green
DC-IN Power
Off
No Power in DC-IN
Alarm
Red
Power1 or Power 2 Disconnect.
Off
Power1 & 2 Connection
PoE LED
Status
Description
PoE 1~8
Yellow
The port is delivering PoE power.
Off
No PD is attached.
Earth Ground Screw
Terminal Block
Relay Output

Korenix
JetNet 3210GP-2C
9
LED
Status
Description
RJ-45 ports
Green on
Link
Blinking
RJ-45 port is transmitting or receiving
packets.
Off
RJ-45port’s link is inactive
Amber On
Link with Speed 1000Mbps
Amber Off
Link with Speed 10/100Mbps
Fiber Port LED
Status
Description
LNK/ACT
Green on
Fiber port is attached with partner.
Blinking
Fiber port is transmitting or receiving
packets.
Off
Fiber port’s link is inactive
Speed
Amber on
Gigabit Speed
Amber off
100Mbps speed
2.2 Wiring the Power Inputs
JetNet 3210GP-2C accepts 12~56V DC power input and boosts to 54~56VDC output
for 802.3af/at standard PoE devices.
1. Insert the positive and negative wires of your DC supply into the V+ and V-
contacts of the terminal block connector. The acceptable wire range is 12 AWG.
2. Tighten the terminal screws to prevent the DC wires from coming loose.
18

Korenix
JetNet 3210GP-2C
10
2.3 Wiring the Relay Output
JetNet 3210GP-2C provides Relay Output. The relay contacts are energized (open)
for normal operation and will close under faulty condition such as Ethernet port link
break.
2.4 Wiring Earth Ground
To ensure the system will not be damaged by noise or electric shock, we suggest
making a direct connection between the JetNet 3210GP-2C and earth ground to
avoid system damage. (Please refer to the upside photo)
1. On the bottom of the JetNet 3210GP-2C, there is one earth ground screw.
2. Loosen the earth ground screw with a screwdriver
3. Tighten the screw after the earth ground wire is connected.

Korenix
JetNet 3210GP-2C
11
2.6 Wiring the Ethernet Ports
JetNet 3210GP-2C Industrial Gigabit PoE Switch support 8 ports with automatic
MDI/MDI-X crossover, PoE Injector, and automatic 10/100Mbps data rate sensing for
10Base-T or 100Base-TX connections. Automatic MDI/MDI-X crossover allows you to
connect to other switches, hubs, or workstations, without regard to using
straight-through or crossover cabling.
Port 1 to port 8 also provides Power over Ethernet function that delivers DC 54V
power through the spare pairs to power the PD.
The following figures depict the schematic diagram of straight-through and crossover
cabling. Note that crossover cables simply cross-connect the transmit lines at each
end to the receive lines at the opposite end.
Straight-through Cabling Schematic Cross-over Cabling Schematic
Note: that Ethernet cables use pins 1, 2, 3, and 6 of an 8-pin RJ45 connector. The

Korenix
JetNet 3210GP-2C
12
signals of these pins are converted by the automatic MDI-X function, as shown in the
table below:
Pin MDI-X
Signals
MDI Signals
1
RD+
TD+
2
RD-
TD-
3
TD+
RD+
6
TD-
RD-
Connect one side of an Ethernet cable into any switch port and connect the other
side to your attached device. The green LNK LED will light up when the cable is
correctly connected. Refer to the LED Indicators section for descriptions of each LED
indicator. Always make sure that the cables between the switches and attached
devices (e.g. switch, hub, or workstation) are less than 100 meters (328 feet).
2.7 Wiring the Fiber Ports
JetNet 3210GP-2C equips 2 gigabit SFP fiber ports. The speed of the SFP port
supports up to 100/1000Base F(X). The SFP ports accept standard MINI GBIC SFP
transceiver. The way to connect the SFP transceiver is to plug in SFP fiber transceiver
fist. Cross-connect the transmit channel at each end to the receive channel at the
opposite end as illustrated in the figure below.
Note: This is a Class 1 Laser/LED product. Don’t stare at the Laser/LED Beam.
Note: 100Base-FX SFP transceiver is optional and can be supported by different
settings
Note: The unit has to use UL recognized Laser Class 1 SFP transceiver.

Korenix
JetNet 3210GP-2C
13
2.8 Connecting Powered Device (PD)
Port 1 to port 8 provide PoE inject function with maximum 30w ability to power up
the powered device use the straight or cross-over Ethernet cable.
The JetNet 3210GP-2C follow the IEEE802.3af/at Alternative A mode connector
assignment.
Be sure the twisted pair cable is bound with the standard RJ-45 pin
If the RJ-45 is bound with the wrong pin number, JetNet will not
recognize the PD and won’t forward DC 54 power to PD, since the
JetNet 3210GP-2C switch following A mode.
Note: This product is designed for in building installation only and is not intended
to be connected to exposed (outside plant) networks.
2.9 DIN-Rail Mounting Installation
The DIN-Rail clip is already attached on the rear side of JetNet 3210GP-2C. It supports
EN 50022 standard DIN Rail, in the following diagram includes the dimension of EN
55022 DIN Rail for your reference.
The DIN rail should behind the spring when
install the JetNet 3210GP-2C onto the
standard DIN Rail.
Follow the steps below to mount the JetNet
3210GP-2C on the DIN-Rail track.
1. Insert the upper end of the DIN-Rail
clip into the back of the DIN-Rail track
from its upper side
2. Lightly push the bottom of the
DIN-Rail clip into the track.
3. Check if the DIN-Rail clip is tightly

Korenix
JetNet 3210GP-2C
14
attached to the track.
To remove the JetNet 3210GP-2C from the track, reverse the steps above.
3. Appendix
3.1 Product Specification
3.2 Revision History
3.1Product Specification
Technology
Standard
IEEE 802.3u 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-TX Gigabit Ethernet
IEEE 802.3z 1000Base-X Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at High Power PoE with 2-Event clasificación
IEEE 802.3x Flow control and back-pressure
Network Performance
Switch Technology
Store and Forward technology
System Throughput
23.8Mega packets per second, 64Bytes packet length
Transfer packet size
64Bytes ~1518Bytes
MAC Address
16K MAC address table
Packet Buffer
2 Mega bits shared packet buffer
Broadcast storm
control:
Default enabled
Traffic threshold:
25M bps@1000Mbps;
10M bps@100Mbps;
1M bps@10 Mbps
Jumbo frame
Up to 10K Bytes

Korenix
JetNet 3210GP-2C
15
Transfer performance
14,880 pps @10Mbps
148,800 pps @100Mbps
1,488,100 pps @1000Mbps
Quality of Service
Compliance with IEEE802.1p with WRR 8:4:2:1 for 4 queues -
Highest/High/Low/Lowest.
Packets are classified as Highest(6,7), High(4,5), Low(0,3), Lowest(1,2),
default Low(0).
Power over Ethernet
Power over Ethernet
IEEE 802.3af/at, End-Span wiring architecture
PoE forwarding
conductor
RJ-45: V+(1,2), V- (3,6)
Power forwarding
capability
IEEE 802.3af:15.4 W, IEEE802.3at:30W
PoE System Power
Budget
Power Budget Reserve by PD declaration. The power budget control
system will reserve power for connected PD device. Once the latest
PD device claimed power over the system surplus power budget, the
highest port of PoE will not be active due to port order mechanism.
System Power Budget: 240Watts at DC 24V/ 120 Watts at DC 12V
Mechanical
Installation
DIN-Rail mounting
Case
Steel metal
Ingress Protection
IP31
Dimension (mm)
96.18 (W) x 132(D) x 135 (H) –w/o DIN Rail Clip
Installation
DIN-rail mounting
Weight
2Kg
Power Requirement
System power
Input voltage: DC 12V or DC 24V, variation range DC 12- 56V
2x DC power input with polarity reverse protection
Input Range
DC 12-56V
Power Consumption
12V AF: PoE 120W
24V AT: PoE 240W

Korenix
JetNet 3210GP-2C
16
Environmental
Operating
Temperature
-40 ~75oC
Operating Humidity
0% ~ 95%, non-condensing
Storage Temperature
-40 ~ 85oC, 0% ~90% Humidity
Hi-Pot
DC 2.25KV for power to chassis ground, Ethernet port to chassis
ground
Regulatory
Approvals
Railway Standard
EN 50121-4
Traffic
E-mark E13
EMC
EMI: EN50121-3-2, FCC Class A, IEC/EN61000-6-4
EMS:EN50121-3-2/EN50121-1, IEC/EN61000-6-2
IEC/EN61000-4-2, IEC/EN61000-4-3, IEC/EN61000-4-4,
IEC/EN61000-4-5, IEC/EN61000-4-6, IEC/EN61000-4-8,
IEC/EN61000-4-9
Variation/Shock
IEC 61373
Free Fall
IEC 60068-2-32 with package Note-1
Warranty
5 Years
*Specifications may change without prior notice
**pending
3.2 Revision History
Edition
Date
Modifications
V1.0
09/14/2019