KOZEN P10 User manual

Technical Specs
ATTENTIO
N
Warning
Read all instructions and safety information before use to avoid injury.
The limit operating ambient temperature of the device declared by the
manufacturer is -10~45°C.
Battery safety
Charge battery only at ambient temperatures ranging from 0~40°C.
Dispose of used batteries according to manufacturer’s instructions.
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type of battery recommended by the manufacturer.
Statement
The equipment damage caused by natural disasters, falling, self disassembly
and non-compliance with the operation specifications is not covered by the
free warranty.
Some details of this document may be inconsistent with the real object due
to the update iteration of the product. Please take the real object as the
standard, and our company reserves the right to interpret this document.
P10
Quick Guide
Items
Specification
Operating System
Android 11.0 go
CPU
[email protected]
Memory
1GB RAM + 8GB ROM (LPDDR3)
Display
6.517” IPS, 720*1600
Camera
2M AF(back) + 2M FF(front)
Scanner
E3 Lite
Printer
2 inch thermal printer
Cellular Network
Support 2g/3g/4g
WIFI
IEEE 802.11a/b/g/n/ac（2.4G/5G）
Bluetooth
Version 5.0, support BLE
Payment
Magnetic Stripe/NFC/IC Card
Interface
USB type-c、Pogo pin(8 pin)
Battery
2500mAh/7.6V (Rated capacity)

Product Diagram
NFC Card Reader
NFC antenna locates at the bottom of the screen and on the printer cover. It’s
used to sense chip and acquire data through contactless way.
IC Card Reader
Used for inserting the bank chip card and getting information securely.
Magnetic Stripe Card Reader
Used for reading encrypt information stored in corresponding cards.
Camera
Used for taking photos, unlock the device by face recognition and complete
intelligent recognition base on it.
Scanner
Used to capture and identify 1D and 2D code.
Power Button
Used for change the running states of device, such as pressing 2~3 seconds
to power on/off or screen capture and pressing 10 seconds to restart
automatically when device is crashed.
Function Button
Used for adjusting the volume or serving as the shortcut of scan. The
function can be customized.
Pogo pin
The 8-pins expanded interface is severed as the channel to connect the charging
cradle for better power supply or finish data transmission between different
devices.
Hand Stripe Ring
Used to fix the hand strap for easy carrying.
Card Selection Instruction
Printer instructions
1) Support 2 inch thermal paper roll with specification of 57*40mm (w*φ)
2) Feed the paper correctly into the paper container in the direction as shown,
and pull some paper outside the cutter;
Note: If the printed paper is blank, please check whether the pap-er roll has
been installed in the correct direction.
Package List
NO.
Items list
Description
1
Device
Default
2
Battery
1pcs,2500mAh/7.6V
3
USB cable
1pcs,1m/2A/type-c
4
User manual
Neutral

FCC Regulations:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC R
ules. These limits are designed to provide reasonable protection against har
mful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in acco
rdance with the instructions, may cause harmful interference to radio commu
nications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equip
ment off and on, the user is encouraged to try to correct the interference by o
ne or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to whic
h the
receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
Changes or modifications not expressly approved by the manufacturer co
uld void the user’s authority to operate the equipment.
Radio Frequency (RF) Energy
This device is designed and manufactured not to exceed the emission limits f
or exposure to radio frequency (RF) energy set by the Federal Communicati
ons Commission of the United States.
The exposure standard for wireless devices employing a unit of measuremen
t is known as the Specific Absorption Rate, or SAR. The SAR limit recomm
ended by the general public is 1.6W/kg. Averaged over one gram of tissue b
y IEEE Std 1528.The FCC has granted an Equipment Authorization for this
product with all reported SAR Levels evaluated as in compliance with the F
CC RF exposure guidelines. While there may be differences between the SA
R levels of various product and at various positions, they all meet the govern
ment requirements.SAR compliance for body-
worn operation is based on a separation distance of 15 mm
between the unit and the human body. Carry this device at least 15 mm away from
your body to ensure RF exposure level compliant or lower to the reported level. T
o support body-
worn operation, choose the belt clips or holsters, which do not contain metallic co
mponents, to maintain a separation of 15 mm between this device and your body.
RF exposure compliance with any body-
worn accessory, which contains metal, was not tested and certified, and using such
body-worn accessory should be avoided.