Kramer K-NET RC-53D User manual

Kramer Electronics, Ltd.
USER MANUAL
Model:
RC-53D
K-NET™ Auxiliary Control Panel
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

Contents
i
Contents
1Introduction 1
2Getting Started 1
2.1 Achieving the Best Performance 2
2.2 Safety Instructions 2
2.3 Recycling Kramer Products 2
3Overview 3
4Defining the RC-53D 3
4.1 Grounding the RC-53D 5
5Using the RC-53D K-NET™ Auxiliary Control Panel 6
6Installing the RC-53D Faceplate, Button Caps and Labels 7
7Operating the RC-53D K-NET™ Auxiliary Control Panel 9
8Technical Specifications 10
Figures
Figure 1: RC-53D K-NET™ Auxiliary Control Panel – Front Panel 3
Figure 2: RC-53D K-NET™ Auxiliary Control Panel – Rear Panel 4
Figure 3: Grounding Connection Components 5
Figure 4: RC-53D connected to the SV-551 SummitView™ Processor / Switcher 6
Figure 5: Sample Button Label Sheet 7
Figure 6: Button Cap Orientation 7
Figure 7: Inserting the Label 7
Figure 8: Placing the Button Cap 8
Figure 9: RC-53D Labels Setup 9
Tables
Table 1: RC-53D K-NET™ Auxiliary Control Panel – Front Panel Features 4
Table 2: RC-53D K-NET™ Auxiliary Control Panel – Rear Panel Features 4
Table 3: Grounding Component Descriptions 5
Table 4: The Commands Configuration 9
Table 5: Technical Specifications of the RC-53D K-NET™ Auxiliary Control Panel 10
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

Introduction
1
1
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing
a world of unique, creative, and affordable solutions to the vast range of problems
that confront the video, audio, presentation, and broadcasting professional on a daily
basis. In recent years, we have redesigned and upgraded most of our line, making the
best even better! Our 1,000-plus different models now appear in 11 groups1that are
clearly defined by function.
Congratulations on purchasing your Kramer RC-53D K-NET™ Auxiliary Control
Panel which is available in European (80mm and 86mm height versions) and
American versions, and can be used as a system controller when connected via
K-NET™2to a Master room controller (for example, the SV-552 SummitView™
Processor / Switcher or one of the Kramer SL series controllers).
2 Getting Started
This user manual is written for the end user. Refer to the separate
K-Config Configuration Guide (available online) for details of how to
install and configure the Room Controller3
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
•Review the contents of this user manual
Go to http://www.kramerelectronics.com to check for up-to-date
user manuals, application programs, and to check if firmware
upgrades are available (where appropriate).
1 GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers; GROUP 3: Control Systems; GROUP 4: Format/Standards
Converters; GROUP 5: Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7: Scan Converters and Scalers;
GROUP 8: Cables and Connectors; GROUP 9: Room Connectivity; GROUP 10: Accessories and Rack Adapters; GROUP 11: Sierra
Products
2 K-NET is a proprietary Kramer protocol for communication between Kramer products
3 The guide provides information about how to set up the system and is updated on a regular basis. For the latest online guide, go to
http://www.kramerelectronics.com
i
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Getting Started
2
2.1 Achieving the Best Performance
To achieve the best performance:
•Use only good quality connection cables (we recommend Kramer high-
performance, high-resolution cables) to avoid interference, deterioration in
signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
•Do not secure the cables in tight bundles or roll the slack into tight coils
•Avoid interference from neighboring electrical appliances that may adversely
influence signal quality
•Position your Kramer RC-53D away from moisture, excessive sunlight and
dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building.
2.2 Safety Instructions
Caution: No operator serviceable parts inside the unit
Warning: Use only the Kramer Electronics input power wall
adapter that is provided with the unit
Warning: Disconnect the power and unplug the unit from the wall
before installing
2.3 Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC
aims to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country
go to our recycling pages at http://www.kramerelectronics.com/support/recycling/.
!
!
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

Overview
3
3
3 Overview
The RC-53D is an auxiliary remote control panel for Master Room Controllers1for
control of A/V equipment in a room.
The RC-53D:
•Features six front panel, single color, backlit buttons designed in two groups;
one group of two buttons, and another group of four buttons
•Has a digital volume control adjustment knob
•Is available as a 2 Gang wall plate for the USA or a 2 Gang wall plate for
Europe2
•Does not require a separate power supply
•Includes an RS-232 serial port
•Includes two K-NET ports and a USB port for firmware upgrade
•Features two programmable LCD displays, one for each button group
4 Defining the RC-53D
Figure 1and Table 1define the RC-53D front panel.
Figure 1: RC-53D K-NET™ Auxiliary Control Panel – Front Panel
1 Such as the Kramer SummitView System or the SL-1 Master Room Controller
2 Available in two height sizes: 8.6cm and 8cm
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Defining the RC-53D
4
Table 1: RC-53D K-NET™ Auxiliary Control Panel – Front Panel Features
# Feature Function
1 SOURCE Buttons Group of four programmable, backlit buttons
1
2 Faceplate Screws Four screws connecting the faceplate to the Rear Box
3 “DISPLAY” and “SOURCE”
Labels
Programmable, 8 character, LCD displays on a blue background
4 DISPLAY Buttons Group of two programmable, backlit buttons
5 Maximum VOLUME LED Lights red, indicating maximum volume
6 VOLUME LEDs Light green, indicating volume level
7 VOLUME Knob Rotate clockwise to increase volume level
Figure 2and Table 2define the RC-53D rear panel.
Figure 2: RC-53D K-NET™ Auxiliary Control Panel – Rear Panel
Table 2: RC-53D K-NET™ Auxiliary Control Panel – Rear Panel Features
# Feature Function
1 Program USB Connector Connect to a computer for firmware upgrade
2
2 Grounding Screw Connect to grounding wire
3 RS-232 Terminal Block For factory use only
4 K-NET Terminal Block Connect the GND to the Ground connection3, connect B (-) and
A (+) to RS-485, and connect +12V to +12V on the companion
unit
5 K-NET Terminal Block
1 By the system integrator only
2 When the unit is connected via K-NET to a Master Room Controller, you can upgrade the firmware via the USB or ETH ports of the
Master Room Controller
3 The ground connection is sometimes connected to the shield of the RS-485 cable (in most applications, it is not connected)
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

Defining the RC-53D
5
5
4.1 Grounding the RC-53D
The grounding screw is used to earth the chassis of the unit to the building ground
preventing static electricity from impacting the performance of the unit.
Figure and3Table define the grounding screw components.3
Figure 3: Grounding Connection
Components
Table 3: Grounding Component
Descriptions
# Component Description
1 M3X6 screw
2 1/8" Toothed Lock Washer
3 M3 Ring Tongue Terminal
To ground the RC-53DLC:
1. Connect the Ring Tongue terminal to the building grounding point wire (it is
recommended to use a green-yellow AWG#18 (0.82mm2) wire, crimped with
a proper hand-tool).
2. Insert the M3x6 screw through the toothed lock washers and the tongue
terminal in the order shown above.
3. Insert the M3x6 screw (with the two toothed lock washers and ring tongue
terminal) into the grounding screw hole and tighten the screw.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Using the RC-53D K-NET™ Auxiliary Control Panel
6
5 Using the RC-53D K-NET™ Auxiliary Control Panel
The installation process is not detailed in this user manual. This user manual is
applicable once the unit is installed and configured1, and includes:
•Setting up the labels on the buttons, according to your specific requirements
•Configuration of the Master room controller via the K-Config Windows®-based
configuration software
Since the auxiliary panel is used as a remote controller for Master Room
Controllers via the proprietary communication channel K-NET (as illustrated in
Figure 4):
•It requires only a K-NET connection to the Master Room controller
•A power supply unit is not required2
•The auxiliary panel can be programmed only via the Master Room controller
(for example, the Kramer SV-551 SummitView™ Processor/Switcher)
Figure 4: RC-53D connected to the SV-551 SummitView™ Processor / Switcher
1 By authorized Kramer technical personnel or by an external system integrator
2 Power supplies are sold separately. Consult your Kramer dealer for details
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

Installing the RC-53D Faceplate, Button Caps and Labels
7
7
6 Installing the RC-53D Faceplate, Button Caps and Labels
This section describes how to install the faceplate, button caps and labels.
Figure 5illustrates a sample button label sheet.
Figure 5: Sample Button Label Sheet
To install the faceplate, button caps and labels:
1. Remove the required labels from the supplied button label sheet.
2. Hold the button cap so that it is oriented as shown in Figure 6with the
“wings” on the left and right sides.
Figure 6: Button Cap Orientation
3. Insert the label inside the cap
Figure 7: Inserting the Label
4. Repeat for all six caps.
ON
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Installing the RC-53D Faceplate, Button Caps and Labels
8
5. Retaining the orientation, place the six button caps on the buttons of the
RC-53D.
Figure 8: Placing the Button Cap
6. Remove the protective foils from both sides of the Perspex (acrylic glass)
windows.
7. Remove the protective foils from both displays.
8. Place the faceplate on the RC-53D so that the four screw mounting holes are
aligned.
9. Insert the four mounting screws and tighten with a screwdriver.
10. Install the volume control knob.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

Operating the RC-53D K-NET™ Auxiliary Control Panel
9
9
7 Operating the RC-53D K-NET™ Auxiliary Control Panel
In the following example1(illustrated in Figure 9), the auxiliary control panel is
labeled with specific functions and each button is programmed2to perform several
tasks3as defined in Table 4.
Table 4: The Commands Configuration
The Label The Macro Sequence
Figure 9: RC-53D Labels Setup
ON •Power up the projector
•Power up the DVD player
•Roll down the projector screen
•1 minute delay (for the projector to heat up)
•The projector selects the DVD input
OFF •Power down the projector
•Stop the DVD player
•Power down the DVD player
•Stop the VCR
•Power down the VCR
•Roll up the projector screen
DVD •Stop the video player
•The projector selects the DVD input
•Play the DVD
VCR •Stop the DVD
•The projector selects the VCR input
•Play the VCR
VOLUME •Use the VOLUME knob to adjust the audio
level
1 This is only one example among numerous possibilities, each button can be programmed as required. In this example, two buttons are
not assigned
2 By the technical installer
3 A macro sequence, including several commands per button, carried out one after the other
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

KRAMER: SIMPLE CREATIVE TECHNOLOGY
Technical Specifications
10
8 Technical Specifications
Table 5defines the technical specifications.
Table 5: Technical Specifications1of the RC-53D K-NET™ Auxiliary Control Panel
PORTS: 2 K-NET on terminal block connectors; 1USB connector, 1 RS-232 on terminal block
connector (factory use only)
POWER SOURCE: 12V DC, 140mA over K-NET
FUSE: 500mA, FSMD 1812
DIMENSIONS: For the USA: 11.4cm x 2.6cm x 11.4cm (4.49" x 1.02" x 4.49", W, D, H)
For Europe: 15.2cm x 1.9cm x 8.6cm (5.98" x 0.75" x 3.39", W, D, H) or
15.2cm x 1.9cm x 8cm (5.98" x 0.75" x 3.15", W, D, H)
WEIGHT: 0.14kg (0.31lbs.) approx.
ACCESSORIES: Screwdriver
1 Specifications are subject to change without notice
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

Kramer Electronics, Ltd.
Web site: www.kramerelectronics.com
E-mail: [e-mail]
P/N: 2900-000567 REV 4
For the latest information on our products and a list of Kramer
distributors, visit our Web site www.kramerelectronics.com,
where updates to this user manual may be found.
We welcome your questions, comments and feedback.
Caution
Safety Warning:
Disconnect the unit from the power supply before
opening/servicing.
P/N:
2900- 000567
Rev:
4
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]