Kramer VP-558 User manual

USER MANUAL
MODEL:
VP-558
Presentation Switcher/Scaler
P/N: 2900-300433 Rev 3 www.kramerAV.com

VP-558 – Contents
i
Contents
1Introduction 1
2Getting Started 2
2.1 Achieving the Best Performance 2
2.2 Safety Instructions 3
2.3 Recycling Kramer Products 3
3Overview 4
3.1 Using the USB Switcher 6
3.2 Using Twisted Pair Cable for HDBT 6
3.3 Defining the VP-558 Presentation Switcher/Scaler 6
4Installing in a Rack 10
5Connecting the VP-558 11
5.1 Connecting the Balanced Stereo Audio Input and Outputs 14
6Controlling the VP-558 15
6.1 Controlling via the Front Panel Buttons 15
6.2 Using the OSD Menu 16
6.3 The OUTPUT 1 Menu 17
6.4 The Main Menu for Outputs 2, 3 and 4 22
6.5 Connecting to the VP-558 via RS-232 25
6.6 Operating via the Ethernet 26
7Using the Embedded Web Pages 30
7.1 Browsing the VP-558 Web Pages 30
7.2 The Switching Page 31
7.3 The Scaler Page 40
7.4 The Device Settings Page 41
7.5 The USB Routing Page 44
7.6 The Audio Settings Page 45
7.7 The EDID Page 49
7.8 The Data Routing Page 51
7.9 The Authentication Page 53
7.10 The About Page 53
7.11 Save or Upload a Configuration 54
8Technical Specifications 55
8.1 Default Communication Parameters 56
8.2 Input Resolutions 57
9The VP-558 RS-232 Communication Protocol 58
9.1 Kramer Protocol 3000 Syntax 58
9.2 Kramer Protocol 3000 –Command List 61
9.3 Kramer Protocol 3000 –Detailed Commands 63
Figures
Figure 1: VP-558 Presentation Switcher/Scaler Front Panel 7
Figure 2: VP-558 Presentation Switcher/Scaler Rear Panel 8
Figure 3: Connecting the VP-558 Presentation Switcher / Scaler 13
Figure 4: Balanced Stereo Audio Connection 14
Figure 5: Unbalanced Stereo Audio Output Connection 14
Figure 6: balanced Stereo Audio Input Connection 14

ii
VP-558 - Contents
Figure 7: Unbalanced Stereo Audio Input Connection 14
Figure 8: Local Area Connection Properties Window 27
Figure 9: Internet Protocol Version 4 Properties Window 28
Figure 10: Internet Protocol Version 6 Properties Window 28
Figure 11: Internet Protocol Properties Window 29
Figure 12: The Loading Page 30
Figure 13: Enter Username and Password 31
Figure 14: The Switching Page 32
Figure 15: The VP-558 Standby Mode 32
Figure 16: The Switching Page –Input and Output Icons 33
Figure 17: The Switching Page –Edit Output Buttons 33
Figure 18: The Switching Page –Edit HDMI/HDBT Output 34
Figure 19: The Switching Page –Edit Audio Output 34
Figure 20: Edit Input Buttons 35
Figure 21: Switching Page –HDMI input Window 35
Figure 22: Switching Page –HDBT input Window 36
Figure 23: Switching Page –SID-X2N Setup Icon 36
Figure 24: Switching Page –SID-X2N Setup Window 36
Figure 25: Switching Page –SID-X2N Setup Icon 37
Figure 26: Switching Page –SID-X2N Setup Window 37
Figure 27: Switching Page –PC input Window 38
Figure 28: HDBT IR transmission Example 39
Figure 29: The Scaler Page –Output 1 40
Figure 30: The Scaler Page –Output 1 for the PC IN Input 40
Figure 31: The Scaler Page –Output 3 41
Figure 32: The Device Settings Page 41
Figure 33: The Device Settings Page –Static IP Confirmation 42
Figure 34: The Device Settings Page –Firmware Upgrade, Choosing a File 42
Figure 35: The Device Settings Page –Firmware Upgrade, Uploading the File 42
Figure 36: The Device Settings Page –Firmware Upgrade Process 43
Figure 37: The Device Settings Page –Firmware Upgrade Complete 43
Figure 38: The Device Settings Page –New Firmware Updated 43
Figure 39: The Device Settings Page –Soft Factory Reset Message 44
Figure 40: The USB Routing Page 44
Figure 41: The USB Tied to a Selected Input 45
Figure 42: The Audio Settings Page –Inputs 46
Figure 43: The Audio Settings Page –Output 1 46
Figure 44: The Audio Settings Page –Monitor 47
Figure 45: The Audio Settings Page –Mic Mixer 48
Figure 46: The EDID Page 49
Figure 47: The EDID Page –Copying the Native Timing 49
Figure 48: The EDID Page –Copying the Default 50
Figure 49: The EDID Page –The Copy EDID Results 50
Figure 50: The Data Routing Page –The Routing Tab 51
Figure 51: The Data Routing Page –The Setting Tab 52
Figure 52: The Authentication Page 53
Figure 53: The About Page 53
Figure 54: Loading a Configuration 54

VP-558 – Introduction
1
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been
providing a world of unique, creative, and affordable solutions to the vast range of
problems that confront video, audio, presentation, and broadcasting professionals
on a daily basis. In recent years, we have redesigned and upgraded most of our
line, making the best even better!
Our 1,000-plus different models now appear in 14 groups that are clearly defined by
function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters; GROUP 11:
Sierra Video Products; GROUP 12: Digital Signage; GROUP 13: Audio; and
GROUP 14: Collaboration.
Congratulations on purchasing your Kramer VP-558 Presentation Switcher/Scaler.
This product, which incorporates HDMI™ technology, is ideal for:
Projection systems in conference rooms, boardrooms, hotels and churches
Meeting rooms with video conferencing systems
Applications with multiple format inputs having varying resolutions at different
distances from the cabinet or rack
Video and audio matrix routing

2
VP-558 - Getting Started
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
Use Kramer high performance high resolution cables
Go to http://www.kramerav.com/downloads/VP-558 to check for up-to-date
user manuals, application programs, and to check if firmware upgrades
are available (where appropriate).
2.1 Achieving the Best Performance
To achieve the best performance:
Use only good quality connection cables (we recommend Kramer high-
performance, high-resolution cables) to avoid interference, deterioration in
signal quality due to poor matching, and elevated noise levels (often
associated with low quality cables)
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighbouring electrical appliances that may
adversely influence signal quality
Position your Kramer VP-558 away from moisture, excessive sunlight and
dust
This equipment is to be used only inside a building. It may only be
connected to other equipment that is installed inside a building.

VP-558 – Getting Started
3
2.2 Safety Instructions
Caution:
There are no operator serviceable parts inside the unit
Warning:
Use only the power cord that is supplied with the unit
Warning:
Do not open the unit. High voltages can cause electrical
shock! Servicing by qualified personnel only
Warning:
Disconnect the power and unplug the unit from the wall
before installing
2.3 Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims
to reduce the amount of WEEE sent for disposal to landfill or incineration by
requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and
recovery of waste Kramer Electronics branded equipment on arrival at the EARN
facility. For details of Kramer’s recycling arrangements in your particular country go
to our recycling pages at http://www.kramerelectronics.com/support/recycling/.

4
VP-558 - Overview
3 Overview
The VP-558 is a high-performance 11x4 presentation matrix switcher/scaler that
can output four independent scaled images (analog, digital and embedded audio
are supported) on both HDMI and HDBaseT outputs. The VP-558 features 6 HDMI
and 4 HDBaseT inputs as well as an analog VGA input and a 4x1 USB switcher.
The VP-558 includes a microphone input, independent stereo audio outputs, a
MONITOR OUT output, an amplified speaker output, and supports audio DSP
features.
The VP-558 features:
Pix-Perfect™ scaling technology - Kramer’s precision pixel mapping and high
quality scaling technology with full up- and down-scaling of video input
signals
System Range for the HDBT inputs and outputs - Up to 70m (230ft)
For optimum range and performance using HDBaseT™, use Kramer's
BC−HDKat6a cable. Note that the transmission range depends on the
signal resolution, source and display used. The distance using
non−Kramer CAT 6 cable may not reach these ranges.
HDTV compatibility
HDCP compliance - the HDCP (High Definition Content Protection) license
agreement allows copy-protected data on the HDMI input to pass only to the
HDMI outputs
Video inputs –six HDMI connectors, four HDBT on RJ-45 connectors and
one VGA on a 15-pin HD connector
Four independently scaled HDMI + HDBT outputs
Output resolutions –1080p/UXGA
A 4x1 USB switcher that can be set to follow the switching of the video layer
or can be used as an independent switcher
OSD (On Screen Display) –for easy setup and adjustment, accessible via
the front panel buttons
Front-panel LCD for display of status

VP-558 – Overview
5
Powerful audio features via DSP technology
Input and output audio level adjustment
Selectable microphone talkover or mix modes
Analog and embedded audio support (inputs and outputs)
Audio inputs - six analog HDMI audio and one analog PC audio on 3.5mm
mini jacks each with individual level controls
One auxiliary stereo balanced audio source or microphone (with Cond/Dyn
and Mono/Stereo selections with 48V phantom voltage)
Audio outputs –four balanced stereo audio on terminal blocks together with
S/PDIF digital outputs on RCA connectors; one monitor out stereo balanced
on terminal block connectors together with an S/PDIF digital output on an
RCA connector
A built-in 2x10W into 4Ω power amplifier with speaker outputs on a 4-pin
terminal block connector
Multiple aspect ratio selections
Selectable panel lock modes
Built-in ProcAmp - color, hue, sharpness, noise, contrast and brightness
Built-in Web pages for easy setup and remote control
Firmware upgrade via the Ethernet
Non-Volatile memory that saves the final settings
Control your VP-558:
Directly, via the front panel push buttons
By RS-232 serial commands transmitted by a touch screen system, PC, or
other serial controller
Remotely, from the infrared remote control transmitter with OSD (on−screen
display)
Via the Ethernet with built-in Web pages
The VP-558 is housed in a 19” 2U rack mountable enclosure, with rack “ears”
included, and is fed from a 100-240 VAC universal switching power supply.