Kramer VS-62HA User manual

P/N: 2900-300469 Rev 3 www.kramerAV.com
USER MANUAL
MODEL:
VS-62HA
6x2 HDMI/Audio Matrix Switcher

Kramer Electronics Ltd.
VS-62HA –Contents
i
Contents
Introduction 1
Getting Started 1
Overview 2
Defining the VS-62HA 6x2 HDMI/Audio Matrix Switcher 4
Mounting VS-62HA 6
Connecting the VS-62HA 7
Connecting a Serial Controller to the VS-62HA via RS-232 8
Connecting to the VS-62HA via Ethernet 8
Connecting the Remote Contact-Closure Switches and LEDs 11
Principles of Operation 12
Automatic Signal Detection 12
Input Switching Modes 12
EDID Operation 12
Step-in Functionality 13
Operating the VS-62HA 6x2 HDMI/Audio Matrix Switcher 14
Switching an Input to an Output 14
Switching Analog Audio 14
Acquiring an EDID from an Output 15
Using the OFF Button 16
Locking and Unlocking the Front Panel Buttons 16
Generating a Test Pattern 16
Configuring and Maintaining the VS-62HA 17
Setting the DIP-Switches 17
Resetting the VS-62HA to Factory Default Settings 17
Upgrading the Firmware 18
Operating the VS-62HA Remotely via the Web Pages 19
Video Switching Page 20
Analog Audio Switching 23
EDID Management 24
Authentication Page 26
Device Setting Page 27
Firmware Upgrade Page 28
About Us Page 29
Wiring the Twisted Pair RJ-45 Connectors 30
Technical Specifications 31
Default Communication Parameters 32
Default EDID 33
Protocol 3000 35
Understanding Protocol 3000 35
Protocol 3000 Commands 36
Result and Error Codes 46

Kramer Electronics Ltd.
VS-62HA –Introduction
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world
of unique, creative, and affordable solutions to the vast range of problems that confront video,
audio, presentation, and broadcasting professionals on a daily basis. In recent years, we have
redesigned and upgraded most of our line, making the best even better!
Congratulations on purchasing your Kramer VS-62HA 6x2 HDMI/Audio Matrix Switcher,
which is ideal for the following typical applications:
•Conference rooms
•Entertainment
•Hospitality
Getting Started
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment
•Review the contents of this user manual
Go to www.kramerav.com/downloads/VS-62HA to check for up-to-date user manuals,
application programs, and to check if firmware upgrades are available (where appropriate).
Achieving the Best Performance
To achieve the best performance:
•For optimum range and performance, use the recommended Kramer cables available
at www.kramerav.com/product/VS-62HA
•Do not secure the cables in tight bundles or roll the slack into tight coils
•Avoid interference from neighboring electrical appliances that may adversely influence
signal quality
•Position your Kramer VS-62HA away from moisture, excessive sunlight and dust
Safety Instructions
Caution:
•This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.
•For products with relay terminals and GPI\O ports, please refer to the permitted rating
for an external connection, located next to the terminal or in the User Manual.
•There are no operator serviceable parts inside the unit.

Kramer Electronics Ltd.
VS-62HA –Introduction
2
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified
personnel only.
•To ensure continuous risk protection, replace fuses only according to the rating
specified on the product label which located on the bottom of the unit.
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/support/recycling/.
Overview
The VS-62HA is a 4K UHD 6x2 matrix switcher for HDMI™and analog audio signals. It
reclocks and equalizes the signals and can route any input to either or both outputs
simultaneously. It supports resolutions of up to 4K UHD including 4K@60Hz (4:2:0).
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
In particular, the VS-62HA features:
•Up to 8.91Gbps data rate (2.97Gbps per graphics channel).
•Maximum resolution of up to 4K@60Hz UHD (4:2:0).
•Support for HDCP 1.4 (High Definition Digital Content Protection).
•HDMI Support –3D, Deep Color, x.v.Color™, Lip Sync, Dolby® TrueHD, Dolby Digital
Plus, DTS−HD®, and 7.1 multi-channel audio as specified in HDMI 2.0.
•Four unbalanced and two balanced audio inputs and two balanced audio outputs on a
matrix switcher.
•Contact closures to mirror front panel switching selection buttons and LEDs.
•Per input EDID capture that copies and stores the EDID from a display device.
•Independent (breakaway) audio routing of HDMI and analog audio content to two
balanced audio ports.
•Programmable step-in functionality when used in conjunction with compatible step-in
devices, such as the SID-X3N and DIP-31 (using an HDMI cable that supports HEC, the
HDMI Ethernet Channel).
•True video clock detection.
•Advanced auto AV switching modes (last connected and priority switching).

Kramer Electronics Ltd.
VS-62HA –Introduction
3
•Non-volatile EDID storage.
•Kramer reKlocking™ & Equalization Technology that rebuilds the digital signal to travel
longer distances.
•A lock button to prevent unwanted tampering with the buttons on the front panel.
•Internal pattern generator.
•Support for Kramer Protocol 3000.
•Static or dynamic DHCP IP addressing.
•Flexible control options including front panel buttons, optional external remote IR
receiver, RS−232, Ethernet, buttons and LED over contact closure, embedded Web
server and step-in.
•Mini-USB port for upgrading firmware.
•19” 1U enclosure for rack mounting.
Using the IR Transmitter
You can use the RC-IR3 IR transmitter to control the machine via an optional external IR
receiver (for example, P/N C-A35M/IRR-50). The external IR receiver can be located up to
15m away from the machine. This distance can be extended to up to 60m when used with
three extension cables (for example, P/N C-A35M/A35F-50).
Before using the external IR receiver, be sure to arrange for your Kramer dealer to insert the
internal IR connection cable (for example, P/N: 505-70434010-S) with the 3.5mm connector
that fits into the REMOTE IR opening on the rear panel. Connect the external IR receiver to
the REMOTE IR 3.5mm connector.
About Fast Switching
To switch to a new digital video signal upon the loss of a digital video signal, older display
devices require the following:
•A long period of time between the signal loss and the signal acquisition
•Physical interconnecting cable disconnection
These enable older display devices to detect and adjust to the new video attributes and
parameters. Therefore, regular switching methods include a 5V signal disconnection and a
delay in switching.
However, many new display devices are now capable of “on-the-fly” switching. Depending on
the display device in use, the VS-62HA enables:
•Fast switching –minor reset, connection kept alive
•Extra fast switching –no reset, connection kept alive
Fast and extra fast switching modes enable split-second switching times when using high
performance display devices or a scaler on the video output.

Kramer Electronics Ltd.
VS-62HA –Defining the VS-62HA 6x2 HDMI/Audio Matrix Switcher
4
Defining the VS-62HA 6x2
HDMI/Audio Matrix Switcher
This section defines the VS-62HA front panel.
Figure 1: VS-62HA 6x2 HDMI/Audio Matrix Switcher Front Panel
#
Feature
Function
1
IR Sensor
Signal receiver for the infrared remote-control transmitter
2
ON LED
Lights green when the device is powered on
3
INPUT Selector
Buttons (1 to 6)
TO OUT 1
Press one of the six inputs to switch it to Output 1
4
OFF Button
Press to turn off HDMI output 1 video and audio
5
EDID Button
Press to capture the EDID (see Switching Analog Audio on page 14)
6
ANALOG Button
Press to select/de-select the analog audio of output 1, colors are as
follows:
green –analog audio follows HDMI video input
red –analog audio breakaway (Web control only)
off –outputs HDMI audio of the selected HDMI input
7
VOL+ Button
Press to increase output 1 volume
8
VOL- Button
Press to decrease output 1 volume
9
MUTE Button
Press to toggle muting of output 1 audio
10
IR LED
Lights yellow when receiving an IR signal
11
INPUT Selector
Buttons (1 to 6)
TO OUT 2
Press one of the six inputs to switch it to Output 2
12
OFF Button
Press to turn off output 2 video and audio
13
LOCK Button
Press to inactivate/activate all front panel buttons to prevent
tampering
14
PATTERN Button
Press to activate the test pattern generator. When the generator is
active, press one of the input buttons to select a test pattern
15
ANALOG Button
Press to select the analog audio of output 2
16
VOL+ Button
Press to increase output 2 volume
17
VOL- Button
Press to decrease output 2 volume
18
MUTE Button
Press to toggle muting of output 2 audio
19
SWAP Button
Press to swap output 1 and output 2
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19

Kramer Electronics Ltd.
VS-62HA –Defining the VS-62HA 6x2 HDMI/Audio Matrix Switcher
5
This section defines the VS-62HA back panel.
Figure 2: VS-62HA 6x2 HDMI/Audio Matrix Switcher Rear Panel
#
Feature
Function
20
AUDIO IN (1-4) 3.5mm Mini
Jacks
Connect to unbalanced stereo audio sources (1-4)
21
AUDIO IN (5-6) 5-pin
Terminal Blocks
Connect to balanced stereo audio sources (5-6)
22
AUDIO OUT (1-2) 5-pin
Terminal Blocks
Connect to balanced stereo audio acceptors (1-2)
23
REMOTE LEDS (1-2)
Terminal Blocks
Connect to LEDS that display the selected input channel (1-6)
24
REMOTE IR 3.5mm Mini
Jack
Connect to an external IR receiver for controlling the device via
an IR remote controller (see Using the IR Transmitter
on page 3).
Covered by a cap. The 3.5mm mini jack at the end of the
internal IR connection cable fits into this opening
25
HDMI IN (1-6) Connectors
Connect to HDMI sources (1-6)
26
HDMI OUT (1-2)
Connectors
Connect to HDMI acceptors (1-2)
27
SETUP DIP-Switches
Sets the device configuration (see Setting the DIP-Switches
on page 17)
28
REMOTE SWITCHES (1-2)
Connect to up to six remote, contact-closure input selection
switches for Output 1 and Output 2 (see Connecting the Remote
Contact-Closure Switches and LEDs on page 11)
29
RESET/FACTORY
DEFAULT Button
Press while power-cycling the device to reset to factory default
parameters (see Default Communication Parameters
on page 32)
30
RS-232 3-pin Terminal
Block
Connect to a PC/serial controller (see Connecting a Serial
Controller to the VS-62HA via RS-232 on page 8)
31
PROGRAM USB Connector
Connect to a PC to upgrade the firmware (see Upgrading the
Firmware on page 18)
32
ETHERNET RJ-45
Connector
Connect to a PC via a LAN (see Connecting to the VS-62HA via
Ethernet on page 8)
33
Power Module (Socket,
Fuse, On/Off Switch)
Connects to mains power and turns the unit on and off
20 21 22 23 24
25 26 27 28 29 30 31 32 23

Kramer Electronics Ltd.
VS-62HA –Mounting VS-62HA
6
Mounting VS-62HA
This section provides instructions for mounting VS-62HA. Before installing, verify that the
environment is within the recommended range:
•Operation temperature –0to 40C (32 to 104F).
•Storage temperature –-40to +70C (-40 to +158F).
•Humidity –10% to 90%, RHL non-condensing.
•VS-62HA must be placed upright in the correct horizontal position.
Caution:
•Mount VS-62HA before connecting any cables or power.
Warning:
•Ensure that the environment (e.g., maximum ambient temperature & air flow) is
compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be used for avoiding
overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
To mount the VS-62HA on a rack
Attach both ear brackets by removing the screws from each side of the
machine and replacing those screws through the ear brackets or place
the machine on a table.
For more information go to www.kramerav.com/downloads/VS-62HA

Kramer Electronics Ltd.
VS-62HA –Connecting the VS-62HA
7
Connecting the VS-62HA
Always switch off the power to each device before connecting it to your VS-62HA. After
connecting your VS-62HA, connect its power and then switch on the power to each device.
To connect the VS-62HA as illustrated in the example in Figure 3:
Figure 3: Connecting the VS-62HA 6x2 HDMI/Audio Matrix Switcher
1. Connect up to six HDMI sources, (for example, a laptop, desktop, VIA Connect PRO) to
the HDMI In connectors.
2. Connect up to six analog audio sources, (for example, a laptop, desktop, a Dante
interface) to the AUDIO IN connectors. AUDIO IN 1 through 4 are unbalanced stereo on
3.5mm mini jacks. AUDIO IN 5 and 6 are balanced stereo audio on 5-pin terminal block
connectors.
3. Connect the two HDMI OUT connectors to up to two HDMI acceptors, (for example, LCD
displays).
4. Connect the two balanced AUDIO OUT 5-pin terminal block connectors to up to two
analog audio acceptors, (for example, audio receivers).
5. If required, connect a PC/controller to the RS-232 port (see Connecting a Serial
Controller to the VS-62HA via RS-232 on page 8) /or the Ethernet port (see Connecting
to the VS-62HA via Ethernet on page 8)

Kramer Electronics Ltd.
VS-62HA –Connecting the VS-62HA
8
6. If required for remote switching, connect up to 6 contact closure switches per channel to
their terminal block connectors (Remote 1 and 2 Switches).
7. If required for remote switch indication, connect up to 6 LEDS per channel to their
terminal block connectors (Remote 1 and 2 LEDS).
8. Connect a power cord to the device and plug it into the mains electricity (not shown in
Figure 3).
9. If required, acquire the EDID (see Switching an Input to an Output on page 21)
Connecting a Serial Controller to the VS-62HA via
RS-232
To connect a serial controller to the VS-62HA:
From the RS-232 9-pin D-sub serial port on the serial controller connect:
•Pin 2 to the TX pin on the VS-62HA RS-232 terminal block
•Pin 3 to the RX pin on the VS-62HA RS-232 terminal block
•Pin 5 to the GND pin on the VS-62HA RS-232 terminal block
Connecting to the VS-62HA via Ethernet
You can connect to the VS-62HA via Ethernet using either of the following methods:
•Directly to the PC using a crossover cable (see Connecting the Ethernet Port Directly to
a PC on page 8)
•Via a network hub, switch, or router, using a straight-through cable (see Connecting the
Ethernet Port via a Network Hub or Switch on page 10)
Note: If you want to connect via a router and your IT system is based on IPv6, speak to
your IT department for specific installation instructions.
Connecting the Ethernet Port Directly to a PC
You can connect the Ethernet port of the VS-62HA directly to the Ethernet port on your PC
using a crossover cable with RJ-45 connectors.
This type of connection is recommended for identifying the VS-62HA with the factory
configured default IP address.
After connecting the VS-62HA to the Ethernet port, configure your PC as follows:
1. Click Start > Control Panel > Network and Sharing Center.
2. Click Change Adapter Settings.
3. Highlight the network adapter you want to use to connect to the device and click Change
settings of this connection. The Local Area Connection Properties window for the
selected network adapter appears as shown in Figure 4.

Kramer Electronics Ltd.
VS-62HA –Connecting the VS-62HA
9
Figure 4: Local Area Connection Properties Window
4. Highlight Internet Protocol Version 4 (TCP/IPv4) by clicking on the item.
5. Click Properties.
The Internet Protocol Properties window appears as shown in Figure 5.
Figure 5: Internet Protocol Version 4 Properties Window
6. Select Use the following IP Address for static IP addressing and fill in the details as
shown in Figure 6.
For TCP/IPv4 you can use any IP address in the range 192.168.1.1 to 192.168.1.255
(excluding 192.168.1.39) that is provided by your IT department.

Kramer Electronics Ltd.
VS-62HA –Connecting the VS-62HA
10
Figure 6: Internet Protocol Properties Window
7. Click OK.
8. Click Close.
Connecting the Ethernet Port via a Network Hub or Switch
You can connect the Ethernet port of the VS-62HA to the Ethernet port on a network hub or
using a straight-through cable with RJ-45 connectors.

Kramer Electronics Ltd.
VS-62HA –Connecting the VS-62HA
11
Connecting the Remote Contact-Closure Switches and
LEDs
You can connect up to six remote, contact-closure switches and LEDs per output to control
the VS-62HA remotely. These switches replicate the Input selection buttons on the front panel
of the VS-62HA.
Figure 7 illustrates the wiring of the switch connections to the terminal block.
Figure 7: Remote Contact-closure Switch and LED Connections

Kramer Electronics Ltd.
VS-62HA –Principles of Operation
12
Principles of Operation
•Automatic Signal Detection on page 12.
•Input Switching Modes on page 12.
•EDID Operation on page 12.
•Step-in Functionality on page 13.
This section describes the operating theory of the VS-62HA and includes:
Automatic Signal Detection
The VS-62HA can automatically detect the presence of a video signal on an input based on
the presence of a video sync or clock signal.
Input Switching Modes
Manual Mode
In Manual switching mode, routing is performed according to the front panel button selection
or according to the remote command selection.
Automatic Mode
Automatic switching can be performed in either of the following ways:
•Input priority. Upon detection of an active input, the input with the highest priority is
automatically selected. Input priority is from the lowest input number (1) to the highest
(6)
•Last Connected. The device automatically selects the most recently connected input.
Should this source become inactive, the device automatically switches to the last
connected input that was active. When turning the device on and more than one input is
active, the input with the highest priority is selected
If a manual selection is made when the device is in Automatic mode, the device enters
Manual Override mode. The manually selected input remains selected as long as it is active.
When a manually selected input becomes inactive, the device returns to Automatic mode.
EDID Operation
The VS-62HA has a default EDID (see Default EDID on page 33) stored on all inputs. This
EDID can be exchanged for either:
•A custom EDID which is uploaded to one or more inputs using Protocol 3000 commands
(see Protocol 3000 on page 35)
–OR–

Kramer Electronics Ltd.
VS-62HA –Principles of Operation
13
•The EDID of a display device connected to an output by using either the front panel
buttons (see Switching Analog Audio on page 14), a Protocol 3000 command, or the
Web pages
The EDID is non-volatile and the last valid EDID is used when the device is powered up.
Step-in Functionality
The VS-62HA can function as a step-in switcher when connected to a suitable HDMI
transmitter, (for example, the SID-X3N), using the correct HDMI cable with HEC support.
Use the Web pages (see Controlling a Remote Transmitter on page 21) to assign remote
device button actions. The default button actions are shown in the following table. Up to three
buttons can be active at the same time.
Command
Action
Echo
Allows a connected controller to be programmed to perform a variety of tasks triggered by the
user buttons, such as, room control, (lights, screen, and so on)
Out1
Step in current input to Output 1
Out2
Step in current input to Output 2

Kramer Electronics Ltd.
VS-62HA –Operating the VS-62HA 6x2 HDMI/Audio Matrix Switcher
14
Operating the VS-62HA 6x2
HDMI/Audio Matrix Switcher
This section describes operating the VS-62HA and consists of:
•Switching an Input to an Output on page 14.
•Switching Analog Audio on page 14.
•Acquiring an EDID from an Output on page 15.
•Using the OFF Button on page 16.
•Locking and Unlocking the Front Panel Buttons on page 16.
•Generating a Test Pattern on page 16.
Switching an Input to an Output
To switch an input to an output, (for example, Input 5 to Output 2):
•Press the Input 5 button in the bottom Output (To OUT 2) row.
The LED lights red and Input 5 is switched to Output 2
After cycling power, auto-switching is only predictable after the first active switching.
Switching Analog Audio
This section describes analog audio switching by means of the front panel buttons. The front
panel buttons only control AFV analog switching. Breakaway analog switching is only
available over Web control. For a description of analog audio switching over the Web, see
Analog Audio Switching on page 23.
To output an analog audio source associated with a given HDMI input:
•Press the ANALOG button for the desired output
The ANALOG button lights green and the analog audio for the selected HDMI input is
routed to the output instead of the embedded HDMI audio
To change the volume of the selected audio input (HDMI or analog):
•Press VOL+ to increase and VOL- to decrease the output volume
To mute the output volume:
•Press the MUTE button for the desired output
The button lights and the volume is turned off
•Press the MUTE button again for the desired output
The button goes off and the volume is turned on

Kramer Electronics Ltd.
VS-62HA –Operating the VS-62HA 6x2 HDMI/Audio Matrix Switcher
15
To exchange audio outputs:
•Press SWAP
Audio OUT 1 routes to OUT 2 and audio OUT 2 routes to OUT 1
•To return the audio outputs to their normal place, press SWAP again
Acquiring an EDID from an Output
You can acquire the EDID from OUT 1 or OUT 2 and copy it to any or all of the six inputs to
be stored in non-volatile memory. You can also reset any or all of the inputs to the default
EDID.
To copy the EDID from an Output to one or more Inputs:
1. Press the EDID button to enter the EDID setting mode.
The EDID button lights.
Note: If there is no button activity for 10 seconds, the device automatically exits the
EDID setting mode to normal operation, the EDID button no longer lights and any
changes made are lost.
2. From the To OUT 1 (top) row, press each of the Inputs to which you want to copy the
EDID from Output 1.
Each selected Input LED lights.
3. From the To OUT 2 (bottom) row, press each of the Inputs into which you want to copy
the EDID from Output 2.
Each selected Input LED lights.
Note: If the VS-62HA reads a corrupted EDID from the sink connected to output 1 or 2, it
writes the default EDID to the input.
4. Press the EDID button.
The button no longer lights and the EDID changes are saved.
To copy the default EDID to one or more Inputs:
1. Press the EDID button to enter the EDID setting mode.
The EDID button lights.
2. For each Input to which you want to copy the default EDID, press both the To OUT 1
and To OUT 2 buttons simultaneously.
Both top row and bottom row Input LEDs light.
3. Press the EDID button.
The button no longer lights and the EDID changes are saved.

Kramer Electronics Ltd.
VS-62HA –Operating the VS-62HA 6x2 HDMI/Audio Matrix Switcher
16
Using the OFF Button
Pressing the OFF button stops the audio and video for each channel at its output.
Locking and Unlocking the Front Panel Buttons
To lock and unlock the front panel buttons:
1. Press and hold the Lock button.
The front panel buttons are locked and the button lights.
2. Press and hold the Lock button again.
The front panel buttons are unlocked and the button no longer lights.
Generating a Test Pattern
For diagnostic purposes, the VS-62HA can generate a number of test patterns on the outputs.
To generate a test pattern on the outputs:
1. Press the Pattern button.
The button lights.
2. Press any of the Input buttons to select a test pattern.
The selected test pattern is generated on the outputs.
To exit the test pattern generator:
•Press the lit Pattern button.
The test pattern generation ceases and the button no longer lights.
Figure 8 shows the test patterns available.
Figure 8: Test Patterns

Kramer Electronics Ltd.
VS-62HA –Configuring and Maintaining the VS-62HA
17
Configuring and Maintaining the
VS-62HA
This section describes the configuration and maintenance of the VS-62HA and consists of:
•Setting the DIP-Switches on page 17.
•Resetting the VS-62HA to Factory Default Settings on page 17.
•Upgrading the Firmware on page 18.
Setting the DIP-Switches
The Setup DIP-switches dictate the behavior of the VS-62HA.
All DIP-switches are off by default.
#
Feature
Description
1
HDCP support on inputs
On—Disable HDCP support on all inputs
Off—Enable HDCP support which is defined by P3000 commands
2
Video mode switching
Output 1
On—Auto
Off—Manual
3
Last connected/Priority
mode Output 1
When DIP-switch 2 is set to Auto (ON):
On—Enable Last Connected mode
Off—Enable Priority mode where the priority of each input is defined by
the input number, (1 is the highest priority)
4
Video mode switching
Output 2
On—Auto
Off—Manual
5
Last connected/Priority
mode Output 2
When DIP-switch 4 is set to Auto (ON):
On—Enable Last connected mode
Off—Enable Priority mode where the priority of each input is defined by
the input number, (1 is the highest priority)
6
N/A
N/A
7
N/A
N/A
8
N/A
N/A
Resetting the VS-62HA to Factory Default Settings
To reset the device to factory default settings:
1. Power off the device.
2. Press and hold down the Reset button on the rear panel.
3. While holding down the Reset button, power on the device.
4. Wait a few seconds and release the button.
The device is reset to its factory settings.
Note: When running a factory reset from Protocol 3000, you must send the two
commands: #FACTORY<CR> and #RESET<CR>.

Kramer Electronics Ltd.
VS-62HA –Configuring and Maintaining the VS-62HA
18
Upgrading the Firmware
The VS-62HA can be upgraded via any of the following:
•Mini USB
•RS-232
•Ethernet
For instructions on upgrading the firmware see “K-Upload Software”.