Kraus Nolen KPF-1673 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2022 Kraus USA Plumbing LLC I REV. April 6, 2022
NolenTM Single Handle
Pull-Down Kitchen Faucet
KPF-1673
R
INSTALLATION MANUAL

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
R

Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and parts list. If any
part is missing or damaged, please contact Kraus Customer Service at 800-775-0703
for a replacement.
·Read all instructions and safety warnings and ensure you have all tools, parts, and
equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on the old faucet
to release any built up pressure. Remove existing faucet. Clean sink or countertop to
remove any debris, plumber’s putty, or silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min) - 1 1/2" (max)
·Max countertop thickness without deck plate: 2 1/4”
·Max countertop thickness with deck plate: 1 3/4”
·1, 2 or 3 hole installation
3
STOP
Tools Required
Adjustable Wrench Phillips Screwdriver Silicone Sealant Safety Goggles
Care & Maintenance
To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
This installation manual is subject to change without further notice.
ACID
R

44
Diagram and Parts List
1. Spray Head
2. Faucet Body
3. Deck Plate Assembly
A. Deck Plate
B. Base Plate
4. Mounting Hardware
A. Rubber & Metal
Washer
B. Mounting Nut
C. Mounting Screws
5. Spray Hose
6. Weight
7. Quick Connector
8. Hot and Cold
Copper Lines
A. Cold
B. Hot
9. Hex Wrench
10. Washer
11. Hot & Cold Waterlines
610
1
9
11 2
5
8B
8A
7
3A
3B
4A
4B
4C
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
R

55
Faucet Installation Procedure
Installer Tip:
Shut off main water supply before installing new faucet.
16 3/8"
(417mm)
9"
(228mm)
9 1/8"
(232mm)
7"
(178mm)
MAX
2 1/4"
(57mm)
3 7/8"
(99mm)
11 1/2"
(291mm)
* Optional Deck Plate
2 3/4"
(70mm)
Ø1 3/8" (35mm)
10 3/8"
(264mm)
1/2"
(12mm)
2X G1/2"
1/2"
(12mm)

66
Step 1. Remove mounting hardware
Step 2A. Faucet installation - with deck plate
Remove the mounting
screws (4C), mounting nut
(4B), and rubber & metal
washer (4A) from the
mounting pipe.
For three-hole installation:
Deck plate (3A), base plate
(3B), and silicone sealant
(optional) are required.
4A
4B
4C
3A
3B

7
Step 2B. Faucet installation - without deck plate
For single-hole installation:
Deck plate (3A), base plate
(3B), and silicone sealant
are NOT required.
Step 3. Install faucet and mounting hardware
Insert faucet body (2) into
hole in countertop or deck
plate assembly (3). Install
mounting hardware (4A, B
& C) from underneath the
countertop.
4A
4B
4C

8
Step 4. Secure mounting hardware
Step 5. Attach spray hose and counterweight
Adjust direction of faucet
body (2) so that handle is on
right side of faucet. Tighten
mounting nut (4B) until snug.
Tighten mounting screws
(4C) to nut with Phillips
screwdriver until snug.
Connect spray hose (5)
to quick connector (7)
attached to supply line.
Install weight (6) on lowest
vertical point on spray
hose (5).
4B
4C
7
5
6

9
Step 6. Connect waterlines
Connect waterlines to hot and
cold copper lines (8). Connect
waterlines (12) to angle
stops. Tighten both ends of
waterlines with a wrench
until snug. Turn on hot and
cold angle stops and check
for leaks.
Step 7. Flush spray hose
Remove spray head (1) from
spray hose (5). Hold tip of
spray hose (5). Turn faucet on
and let the water run for 60
seconds to ush any debris.
NOTE: Please make sure washer (11) is
installed attaching spray head to hose.
12
5
1
8
Step 8. Check for leaks
Check for leaks at the
connections. Retighten if
necessary.
NOTE: Check the filter washer in the
waterlines before connecting to the
angle stops.

10
Replacement Parts
1. Spray Head
2. Check Valve
3. Spray Hose
4. Hose Guide
7. Handle Button
8. Set Screw
6. Metal Handle
9. Cartridge Cover
11. Locking Nut
13. Cartridge
12. Cartridge Housing
15. Deck Plate
16. Base Plate
21. Protective Sleeve
24. Weight
26. Hex Wrench
22. Check Valve
23. Quick Connector
Replacement Parts List Finish/Color Part #
KP06091
KP06105
KP06098
KP06045
KP06292
KP06000
KP06026
KP06052
KP06080
KP06059
KP06019
KP06005
KP06101
KP06063
KP06008
KP06011
KP06041
KP06028
KP06067
KP06068
KP06057
KP06104
KP06108
KP06015
KP06094
KP06050
KP06074
KP06200
KP06185
SFS, CH*
25. Hot & Cold Waterlines
10. O-Ring
14. Rubber O-Ring
SFS, CH*
*Denotes faucet component color options:
SFS - Spot Free Stainless Steel
CH - Chrome
BL - Black
GR - Grey
28. Mounting Hardware Kit
(includes KP06041,KP06028
KP06067,KP06068)
17. Rubber Washer
19. Mounting Nut
20. Mounting Screws
18. Metal Washer
27
4
3
2
1
11 8
13 12 10 9 7
14 15
22
23
24
17
18
19
20
21
16
5
26
6
25
5. Spout Clip
27. Washer
SFS, CH*
SFS, CH*
SFS, CH*
BL, GR*
29
29. Filter Washers