Kraus Arlo KBF-1200 User manual

INSTALLATION MANUAL
Arlo™ Single Handle
Vessel Faucet
KBF-1200
ZZZNUDXVXVDFRP,7ROO)UHH,.UDXV86$3OXPELQJ//&,5HY$SULO

2
Congratulations on the purchase of your new
R
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

13
3
Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Read all instructions and safety warnings and ensure you have all tools,
parts, and equipment necessary for a safe installation.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
·Pre-drilled hole size requirement: 1 3/8" (min)
·Max countertop thickness: 2 1/2”
Care & Maintenance
* To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
* This installation manual is subject to change without further notice.
ACID
R
STOP
For technical assistance or replacement parts, please contact Kraus Customer
Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
Tools Required
Wrench Phillips Screwdriver Silicone Sealant Safety Goggles Pipe Tape

Diagram and Parts List
F
E
J
H
G
I
A
B
C
D
A. Faucet Body
B. Plastic Washer
C. Metal Washer
D. Nut & Screws
E. Waterlines
4
F. Flange & Washer
G. Aerator
H. Aerator Key
I. Hex Wrench
J. Drain

Faucet Dimensions
2 1/4"
[56mm]
12 1/8"
[307mm]
2 1/2"
[64mm]
8 1/8"
[208mm]
5"
[128mm]
6 3/4"
[171mm]
3/8" compression
5
Installer Tip:
Shut off main water supply before installing new faucet.

B
C
A
A
F
D
B
C
E
D
Before installation, ensure that the
flange (F) is placed on the bottom of
the faucet assembly (A). Place the
faucet (A) through the hole in the
countertop. Secure the faucet (A) to
the countertop using the plastic
washer (B), metal washer (C) and nut &
screws (D) provided. Hand tighten the
nut onto the end valve shank. Lock the
nut into position by tightening the
screws (D) with a phillips screwdriver.
6
Step 1: Remove washers and nut
Step 2: Installing the faucet
Shut off the water supply. Remove the
old faucet. Clean the mounting
surface. Remove the plastic washer (B),
metal washer (C) and nut & screws (D)
from the faucet (A).
D

E
2
3
6
7
4
5
1
Step 3: Connect waterlines to main valve
Step 4: Install Press pop-up assembly
Unscrew the nut (6) from the pop-up
body (2), move over the tail pipe (7)
and washer (5), then unscrew the
coupling nut (4) and remove the
washer (3).
Attach waterlines (E) to angle stops
and tighten until snug. Turn on angle
stops and check for leaks (DO NOT
TURN FAUCET ON).
7

1
10
9
11
12
Place the washer (1) underneath the
flange of the pop-up body (2). Slide the
pop-up body (2) down through the
drain hole on the vessel or basin sink.
From the underside of the sink, slide the
washer (3) against the bottom of the
vessel or basin sink, thread on the
coupling nut (4) and tighten. Do not
overtighten.
After installing the faucet, remove the
aerator (G) with the included aerator
key (H). Turn the water on for 30
seconds to remove any debris.
Reassemble the aerator (G ).
2
3
4
1
Slide the nut (6) over the tail pipe (7).
Place the washer (5) into the nut and
tighten. Do not overtighten.
G
H
279
10 31/32”
Minimum distance 90mm
Cold Water
Max35
217
8 17/32”
Max1 3/8”
8
Step 5: Flush faucet
Step 4: Install Press pop-up assembly - continued
2
3
4
1
6
7
5

Replacement Parts
8
9
13
7
10
2
3
4
5
6
1
11
14
15
Less than 90mm
32 3/32”
Ø35~Ø38
1
23
4
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30°
10
8
7
Ø35~Ø38
Replacement Parts List Part #
2. Set Screw
Finish / Color
KP27001
1. Cover Button KP27002
3. Handle KP27046
5. Bonnet Nut KP27049
4. Cap KP27048
6. Screw KP27047
7. Cartridge KP27050
9. Aerator Key KP27052
8. Aerator KP27051
10. Plastic Washer KP27146
11. Metal Washer KP27147
14. Drain KP27059
15. Hex Wrench KP27020
CH, SFS, ORB, MB
BG*
CH, SFS, ORB, MB
BG*
GR, BL*
12
CH, SFS, ORB, MB
BG*
13. Flange & Washer KP27053
CH, SFS, ORB, MB
BG*
12. Nut & Screws KP27148
*Denotes faucet component color options:
CH - Chrome
SFS - Spot Free Stainless Steel
ORB - Oil Rubbed Bronze
MB - Matte Black
BG - Brushed Gold
GR - Grey
BL - Black
16
16. Filter Washer KP27167
9

10
Troubleshooting
If you have followed the instructions carefully and your faucet still does not work properly,
take the following corrective steps:
Leakage under the handle.
PROBLEM CAUSE ACTION
Bonnet nut (5) has
come loose.
Remove the index (1). Loosen set screw
(2) with hex wrench (15). Remove the
handle (3). Unscrew cap (4) (by hand
only). Tighten bonnet nut (5) with an
adjustable wrench.
Aerator drips or has
inconsistent water flow
pattern.
Aerator (8) is dirty or not
seated properly
Unscrew aerator (8) with aerator
key (9) and clean out debris.
Water will not shut off
completely.
Cartridge may need to be
adjusted or replaced
Remove the index (1). Loosen set screw
(2) with hex wrench (15). Remove the
handle (3). Unscrew cap (4) (by hand
only). Loosen the bonnet nut (5) with an
adjustable wrench. Remove the cartridge
(7). Check for cracks.
There is leaking from the
sink drain at the base of
the sink.
The sink has a rough or
irregular surface.
Apply additional silicone sealant to the
beveled side of the drain flange.
Retighten and test for leaks.
There is a low flow of
water.
The screen filters in the
hose connectors are dirty
Turn off the water supply at the water
valves and unscrew the hose connectors
from the water supply lines. Clean the
screens in the water lines with hot water,
removing any debris or calcium build up.