Kraus Allyn FF-102 User manual

AllynTM Transitional Stand Alone
Filtration Faucet
FF-102
R
INSTALLATION GUIDE

Tools Required
Adjustable Wrench Phillips Screwdriver Supply Lines
3
Prior to Installation:
·
Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact
Customer Service.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
Clean sink or countertop to remove any debris, plumber’s putty, or
silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 1/4" (min)
·Max countertop thickness: 3 1/16
Safety GogglesSilicone Sealant

Diagram and Parts List
C
D
E
F
G
A. Faucet Assembly
B. Flange
C. Rubber Washer
D. Metal Washer
E. Mounting Nut
F. Connector 3/8"
G. Connector 1/4"
A
B

Installer Tip:
Shut off main water supply before installing new faucet.
Faucet Dimensions
5
8 3/8“
[214mm]
4 1/2”
[115mm]
10 3/8“
[262mm]
3 1/8“
[80mm]
2 3/8”
[61mm]
1 3/4”
[45mm]

Step 1: Preparing for installation
Remove the rubber washer (C),
metal washer (D), and mounting
nut (E) from the end of the stud.
Step 2. Installing the faucet assembly
6
C
D
E
A
C
D
E
Place the faucet assembly (A)
through the selected hole in the
sink or countertop. On the
underside of the sink or countertop,
slide the rubber washer (C) and
metal washer (D) onto the stud.
Thread the mounting nut (E) onto
the stud, and tighten securely
using your wrench.

Step 3. Connecting the quick connect adaptor and water line
7
A
F
3/8 in. Water line from
filtration system
Thread the quick connect adaptor
(F) onto the end of the faucet
assembly (A) stud, and tighten
securely using a wrench. Connect
the 3/8 in. water line from the
filtration system by pushing the
line into the connector (F). Pull
down on the 3/8 in. line slightly to
ensure the quick connect fitting
has engaged.
Note: A 1/4" connector (G) is
included for 1/4" water lines.

Replacement Parts
Replacement Parts List Finish/Color Part #
KP44046
KP44047
KP44067
1. Locking Ring
2. O-Ring
3. Cover Button
4. Handle
5. Cartridge Screw
6. Cartridge Cover
7. Cartridge
8. Flange
9. Rubber Washer
10. Metal Washer
11. Mounting Nut
12. Connector 1/4"
*Denotes faucet component color options:
SFS - Spot Free Stainless Steel
MB - Matte Black
BG - Brushed Gold
KP44065
KP44066
KP44064
KP44048
KP44063
KP44052
KP44053
KP44054
KP44057
8
SFS, MB, BG*
13. Connector 3/8" KP44055
SFS, MB, BG*
SFS, MB, BG*
SFS, MB, BG*
1
2
8
9
10
11
12
13
3
4
5
6
7

Trouble-Shooting
If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:
Leakage under faucet handle Cartridge has come loose Remove index and loosen set screw with
hex wrench. Remove the handle. Tighten
cartridge with an adjustable wrench.
Care & Maintenance
* To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
* This installation manual is subject to change without further notice.
Water does not shut off
completely
Cartridge may need to be
adjusted or replaced.
Remove index and loosen set screw with
hex wrench. Remove the handle . Tighten
cartridge with an adjustable wrench.
Remove the cartridge. Check for cracks.
ACID
PROBLEM CAUSE ACTION
9