Kraus Arlo KVF-1200CH User manual

Arlo™Single Lever Vessel Faucet
KVF-1200
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV. FEB 26, 2020

1
Congratulations on the purchase of your new
Kraus plumbing xture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [e-mail]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
1

2
Tools you will need:
13
Wrench Phillips Screwdriver Safety Goggles
Silicone Sealant
(optional)
Pipe Tape
Prior to Installation:
•Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
•Pre-drilled countertop hole size requirement: 1-3/8”(min)
•Max countertop thickness: 2 1/2”
Turn off the hot and cold water lines at the angle stops and turn on the old faucet
to release any built-up pressure

Diagram and Parts List
F
E
J
H
G
I
A
B
C
A. Faucet Body
B. Plastic Washer
C. Metal Washer
D. Nut & Screws
E.
Waterlines
F. Flange & Washer
G. Aerator
H. Aerator Key
I. Hex Wrench
3
J. Drain
D

Faucet Dimension
Installer Tip:
4
2 1/4"
[56mm]
12 1/8"
[307mm]
2 1/2"
[64mm]
8 1/8"
[208mm]
5"
[128mm]
6 3/4"
[171mm]
3/8" compression

Step 1: Remove washers and nut
old faucet. Clean the mounting surface.
Remove the plastic washer (B), metal
washer (C) and nut & screws (D) from
the faucet (A).
B
C
Step 2: Install faucet
A
A
F
D
5
B
C
D
E
D
Before installation, ensure that the
flange (F) is placed on the bottom
of the faucet assembly (A). Place faucet (A)
through the 1-3/8” holes in countertop .
Secure the faucet (A) to the countertop
using the plastic washer (B), metal
washer (C) and nut & screws (D) provided.
Hand tighten the nut onto the end valve
shank. Lock the nut into position by
tightening the screws (D) with
a phillips screwdriver.

Step 4: Install Press pop-up assembly
Unscrew the nut (6) from the pop-up
body (2), move over the tail pipe (7)
and washer (5), then unscrew the
coupling nut (4) and remove the
washer (3).
E
2
3
6
7
4
5
Step 3: Connect waterlines to main valve
Attach waterlines(E) to angle stops
and tighten until snug. Turn on angles
stops and check for leaks (DO NOT TURN
FAUCET ON)
6
1

1
10
9
11
12
Step 4: Install Press pop-up assembly
Place the washer (1) underneath the
the pop-up body (2) down through
the drain hole on the vessel or basin.
From underside, slide the washer (3)
against the bottom of the vessel or
basin, thread on the coupling nut (4)
and tighten. Do not overtighten.
Step 5: Flush faucet
After installing faucet, remove
aerator (G) with included aerator
key (H). Turn water on for 30
seconds to remove any debris.
Reassemble aerator (G).
2
3
4
1
6
7
5
Slide the nut (6) over the tail pipe (7).
Place the washer (5) into the nut and
tighten. Do not overtighten.
G
H
279
10 31/32”
Minimum distance 90mm
Cold Water
Max35
217
8 17/32”
Max1 3/8”
7

Replacement Parts
8
9
13
7
10
2
3
4
5
6
1
11
14
15
Less than 90mm
32 3/32”
Ø35~Ø38
1
23
4
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10
8
7
Ø35~Ø38
8
Replacement Parts List Part #
2. Set Screw
Finish / Color
KP27001
1. Cover Button KP27002
3. Handle KP27046
5. Bonnet Nut KP27049
4. Cap KP27048
6. Screw KP27047
7. Cartridge KP27050
9. Aerator Key KP27052
8. Aerator KP27051
10. Plastic Washer KP27146
11. Metal Washer KP27147
14. Drain KP27059
15. Hex Wrench KP27020
CH, SFS, ORB, MB
BG*
CH, SFS, ORB, MB
BG*
GR, BL
12
CH, SFS, ORB, MB
BG*
13. Flange & Washer KP27053
CH, SFS, ORB, MB
BG*
12. Nut & Screws KP27148
*Denotes faucet component color options:
CH - Polished Chrome
SFS - Spot Free Stainless Steel
ORB - Oil Rubbed Bronze
MB - Matte Black
BG - Brushed Gold
GR - Grey
BL - Black
16
16. Filter Washer KP27167

Troubleshooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PRO B L E M C A U S E A C T I O N
Leakage under the
handle
Bonnet nut (5) has
come loose
Remove the index (1). Loosen
set screw (2) with hex wrench
(15). Remove the handle (3).
Unscrew cap (4) (by hand only).
Tighten bonnet nut (5) with
an adjustable wrench
Aerator drips or has
inconsistent water ow
pattern
Aerator (8) is dirty or
not seated properly
Unscrew aerator (8)
with aerator wrench (9)
and clean out debris
Water will not shut o
completely
Cartridge may need to
be adjusted or replaced
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
1
11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
Remove the index (1). Loosen
set screw (2) with hex wrench
(15). Remove the handle (3).
Unscrew cap (4) (by hand only).
Tighten bonnet nut (5) with an
adjustable wrench. Remove the
cartridge (7). Check for cracks
There is leaking from the
sink drain at the base of
the sink.
The sink has a rough or
irregular surface.
Apply additional silicone
sealant to the beveled side of
and test for leaks
9
water. hose connectors is dirty. water valve and unscrew the
hose connectors from water
supply lines. Clean the screen
in the waterlines with hot
water, removing any debris
or calcium build up.