Kraus KHF410-30 User manual

KHF410-30, KHF410-33, KHF410-36
Stainless Steel Farmhouse
Kitchen Sinks
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV. October 26, 2020
R
INSTALLATION MANUAL

Congratulations on the purchase of your new Kraus plumbing fixture!
Please keep the box and packaging materials until your product is completely installed. If you have
any questions, require technical assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt with purchase date for
reference.
If for any reason this product does not meet your expectations, please be sure to repack this
product in the original box and packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

3
Prior to Installation:
·Inspect the sink prior to installation to make sure the sink has not been damaged during
shipping
·Use the cut-out template provided by Kraus
·Observe all plumbing and building codes according to your state requirement
·Additional floor and wall preparation may be required to avoid damaging the product
·Make sure to purchase the correct cabinet for your farmhouse sink. Farmhouse base
cabinets should be 3" larger than the actual size of the sink
·Not recommended to be installed with laminate countertop
For technical assistance or replacement parts, please contact Kraus Customer Service
and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus sink. Should
there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a
licensed professional.

44
NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen sinks with
countertop materials other than wood, marble or granite.
Tools you will need
Safety Goggles Silicone Adhesive Jig Saw
Phillips Screwdriver Tape Measure Pencil
Drill Acetone
Screwdriver Level
Acetone
Parts List
·Cut-Out Template
·Mounting Hardware
·Bottom Grid
·Strainer ST-1
·Drain Cap STC-2

55
Dimensions:
29 7/8" (758.8mm)
27 7/8" (708mm)
10"
(254mm)
5"
(127mm)
9 1/2"
(241.3mm)
9"
(228.6mm)
Model #: KHF410-30*
Sink Dimensions: 29 7/8” x 20 3/4” x 10”
Min Cabinet Size: 33”
Model #: KHF410-33
Sink Dimensions: 32 7/8” x 20 3/4” x 10”
Min Cabinet Size: 36”
Model #: KHF410-36*
Sink Dimensions: 35 7/8” x 20 3/4” x 10”
Min Cabinet Size: 39”
20 3/4" (527.1mm)
17 1/4" (438.2mm)
5"
(127mm)
Typical note: *= Special Order
1"
(25.4mm)
3 1/2"
(90mm)
2 1/2"
(63.5mm)
R3/8"
(10mm)
32 7/8" (835mm)
30 7/8" (784.2mm)
10"
(254mm)
5"
(127mm)
9 1/2"
(241.3mm)
9"
(228.6mm)
20 3/4" (527.1mm)
17 1/4" (438.2mm)
5"
(127mm) 1"
(25.4mm)
3 1/2"
(90mm)
2 1/2"
(63.5mm)
R3/8"
(10mm)
35 7/8" (911.2mm)
33 7/8" (860.4mm)
10"
(254mm)
5"
(127mm)
9 1/2"
(241.3mm)
9"
(228.6mm)
20 3/4" (527.1mm)
17 1/4" (438.2mm)
5"
(127mm) 1"
(25.4mm)
3 1/2"
(90mm)
2 1/2"
(63.5mm)
R3/8"
(10mm)

66
Step 1. Determine Reveal Type
·Use scissors to cut along the line of the paper template for your desired reveal type
(Negative, Positive, or Flushed Reveal)
NOTE: Make sure clearance is suitable
for backsplash, faucet and plumbing
for the sink.
Step 2. Position Template
·Check the cut-out template against the actual sink to ensure a proper sized cut-out.
·Place the cut-out template in the desired location on the countertop.
KRAUS Recommended Installation Type
3/8” Positive
Flushed/Zero
Centerline
3/8” Positive Reveal
Flushed/Zero Reveal
1/8” Negative Reveal
1/8” Negative

7
Step 3. Trace Template
·Trace template on countertop with a pencil.
NOTE: Please use the appropriate saw
that best fits your countertop material.
Step 4. Cut Countertop
·Cut the opening in the countertop by carefully following the traced line.

8
Step 5. Cut Cabinet Front
·Measure height of apron front. Add 1/16" to the dimension when you mark base cabinet front cutout. Use jigsaw to
cut.
1/2"
(13mm)
Step 6. Set Up Mounting Brackets
·Turn countertop over and align sink with countertop. Decide location for mounting brackets.
·Mounting holes should be 1/2" from edge of sink.

9
Step 7. Drill Hole in Countertop
·Drill 3/8" diameter x 1/2" deep hole in the countertop.
3/8 1/2

10
Step 8. Install Anchors
·Insert anchors into drilled holes and lightly tap with a hammer until flush.