Kraus Oletto KPF- 2620 User manual

Oletto™ Single Handle Kitchen Faucet
KPF- 2620
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2022 Kraus USA Plumbing LLC I REV. Jul 18, 2022

Congratulations on the purchase of your new
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [e-mail]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
1

Prior to Installation:
•Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
•Pre-drilled countertop hole size requirement: 1-3/8”(min)
•Max countertop thickness: 2-1/8”
Tools you will need:
13
Wrench Phillips Screwdriver Safety Goggles
Silicone Sealant
(optional)
Pipe Tape
2
to release any built-up pressure
Care & Maintenance
* To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
* This installation manual is subject to change without further notice.
ACID
STOP

3
A. Spray Head
C. Escutcheon
D. Gasket
F. Weight
B
Diagram and Parts List
G. Weight Clip
H. Quick Connector
B. Faucet Body
E. Easy Install Assembly
C
D
G
H
I. 2.5mm Hex Wrench
J. 6mm Hex Wrench
F
A
E
I
J

4
Faucet Dimension
Installer Tip:
10 1/8''
[258.8mm]
15 1/4''
[388.8mm]
Max: 2 1/8''
[53.4mm]
10 5/8''
[269.7mm]
8 7/8''
[224.6mm]
7 3/8''
[187.4mm]
2 1/2''
[62.9mm]
10 1/2''
[265.2mm]
8 7/8''
[224.6mm]
7 1/8''
[181.6mm]
Max: 2 3/8''
[59.6mm]
Ø2 1/8''
[53.0mm]
3/8”-compression

5
Step 1a: Installing the easy install assembly (Without escutcheon)
Shut o the water supply. Remove the old
faucet. Clean the mounting surface. Check
for the proper thickness of the sink.
Insert the base (a) into sink. If your model
does have a escutcheon, skip to step 1 b.
Step 1b: Installing the easy install assembly (With escutcheon)
Place the escutcheon (C) and the gasket (D)
on the sink. Insert the base (a) into
escutcheon (C). Note: “Front” on the base (a)
must face the front of the sink. The two
mounting plates (b) on the base (a) must be
loose and movable during the installation of
the base (a). If the sink is uneven, use silicone
under the gasket (D).
a
b
a
C
D
C
b
NOTE: “Front” on the base (a) must face the
front of the sink. The two mounting plates (b)
on the base (a) must be loose and movable
during the installation of the base (a).

Step 2: Installing the easy install assembly
6
Fig 1 Fig 2
Press the base (a) and escutcheon (C) so that they can not move, then turn the
screws with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown Fig 1.
When the mounting plates (b) make contact with the sink (1), continue to turn
the screw with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown
Fig 2, until the base (a) is completely tightened and secured, as shown Fig.4.
Fig 3
Fig 4
C
J
a
b1
C
J
a
b
1
C
J
a
b
1
C
J
a
b
1

Step 3: Installing the faucet
7
Insert the hose (1)、supply lines (2) and quick connect hose (3) one by one
through the hole of the base (a). Carefully insert the hoses into the base.
Place the faucet assembly onto the base (a) as shown in the above gure.
Secure the faucet assembly (B) by tightening the set screw with the provided
hex wrench (I, Hex: 2.5 mm).
2
1
3
a
I
B

8
Step 4: Securing the faucet assembly
Install the weight clip (G) at the point of
the hose marking "weight here". Insert
the weight (F) onto the weight clip (G)
by sliding it down onto the weight clip (G).
Step 5: Connect waterlines to main valve
Attach waterlinestoangle stops
and tighten until snug. Turn on angle
stops and check for leaks (DO NOT TURN
FAUCET ON).
Weight
here
Weight
here
G
F
NOTE
are installed before connecting to
the main valve

9
Step 6: Flush faucet
Pull the hose assembly out of the spout and
remove the spray head (A) by unscrewing it
from the hose in a counterclockwise
direction. Be sure to hold the end of the hose
down into the sink and turn the faucet on to
the warm position where it mixes hot and
cold water. Flush the water lines for one
minute. This ushes away any debris that
could cause damage to internal parts. Check
for leaks. Re-tighten any connections if
necessary, but do not overtighten. Reinstall
the spray head (A) by hand tightening it
back onto the sprayer hose.
After installation is completed, turn on the
hot and cold water supplies. Check for leaks.
NOTE: Please make sure washer is
installed attaching sprayer to hose.
A