Kraus Kore KWF210-24 User manual

KWF210-24, KWF210-27,
KWF210-27/PGM, KWF210-30,
KWF210-33, KWF210-33/PGM,
KWF210-36, KWF410-30, KWF410-33,
KWF410-33/PGM, KWF410-36
Kore Workstation Stainless
Steel Farmhouse Kitchen Sinks
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV. October 26, 2020
R
INSTALLATION MANUAL

Congratulations on the purchase of your new Kraus plumbing fixture!
Please keep the box and packaging materials until your product is completely installed. If you have
any questions, require technical assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt with purchase date for
reference.
If for any reason this product does not meet your expectations, please be sure to repack this
product in the original box and packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

3
Tools you will need:
NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen sinks with
countertop materials other than wood, marble or granite.
Prior to Installation:
·Inspect the sink prior to installation to make sure the sink has not been damaged during
shipping
·Use the cut-out template provided by Kraus
·Observe all plumbing and building codes according to your state requirement
·Additional floor and wall preparation may be required to avoid damaging the product
·Make sure to purchase the correct cabinet for your farmhouse sink. Farmhouse base
cabinets should be 3" larger than the actual size of the sink
·Not recommended to be installed with laminate countertop
For technical assistance or replacement parts, please contact Kraus Customer Service
and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus sink. Should
there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a
licensed professional.
Safety Goggles Silicone Adhesive Jig Saw
Phillips Screwdriver Tape Measure Pencil
Drill Acetone
Screwdriver Level
Acetone

44
Parts List
KWF210-24
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-24
·Strainer ST-1
·Drain Cap STC-2
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS101BB
KWF210-27
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-27
·Strainer ST-1
·Drain Cap STC-2
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103BB
KWF210-27/PGM
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-27/PGM
·Strainer ST-1/PGM
·Drain Cap STC-2/PGM
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103BB
KWF210-30
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-30
·Strainer ST-1
·Drain Cap STC-2
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103BB
KWF210-33
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-33
·Strainer ST-1
·Drain Cap STC-2
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103BB
KWF410-36
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-36
·Strainer ST-1
·Drain Cap STC-2
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103BB
KWF210-33/PGM
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-33/PGM
·Strainer ST-1/PGM
·Drain Cap STC-2/PGM
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103AC
KWF210-36
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-36
·Strainer ST-1
·Drain Cap STC-2
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103BB
KWF410-30
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-30
·Strainer ST-1
·Drain Cap STC-2
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103BB
KWF410-33
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-33
·Strainer ST-1
·Drain Cap STC-2
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103BB
KWF410-33/PGM
·Cut-Out Template
·Mounting Hardware
·Bottom Grid KBG-UN1-33/PGM
·Strainer ST-1/PGM
·Drain Cap STC-2/PGM
·Rolling Mat KRM-11BL
·Cutting Board KCB-WS103AC

55
Dimensions:
Model #: KWF210-24
Sink Dimensions: 23 7/8” x 20 1/4” x 10”
Min Cabinet Size: 27”
Model #: KWF210-27 & KWF210-27/PGM
Sink Dimensions: 26 7/8” x 20 1/4” x 10”
Min Cabinet Size: 30”
Model #: KWF210-30
Sink Dimensions: 29 7/8” x 20 1/4” x 10”
Min Cabinet Size: 33”
29 7/8" (758.8mm)
28" (711.2mm)
10"
(254mm)
5"
(127mm)
3 1/2"
(90mm)
9 1/2"
(241.3mm)
1"
(25.4mm)
20 1/4" (514.4mm)
16" (406.4mm)
17" (431.8mm)
5"
(127mm)
32 7/8" (835mm)
31" (787.4mm)
5"
(127mm)
3 1/2"
(90mm)
9 1/2"
(241.3mm) 1"
(25.4mm)
10"
(254mm)
9"
(228.6mm)
19 1/2" (495.3mm)
16" (406.4mm)
17" (431.8mm)
5"
(127mm)
9"
(228.6mm)
19 1/2" (495.3mm)
20 1/4" (514.4mm)
Model #: KWF210-33 & KWF210-33/PGM
Sink Dimensions: 32 7/8” x 20 1/4” x 10”
Min Cabinet Size: 36”
23 7/8" (606.4mm)
22" (558.8mm)
5"
(127mm)
3 1/2"
(90mm)
1"
(25.4mm)
20 1/4" (514.4mm)
16" (406.4mm)
17" (431.8mm)
5"
(127mm)
19 1/2" (495.3mm)
10"
(254mm)
9"
(228.6mm)
9 3/4"
(247.7mm)
26 7/8" (682.6mm)
25" (635mm)
5"
(127mm)
20 1/4" (514.4mm)
16" (406.4mm)
17" (431.8mm)
5"
(127mm)
19 1/2" (495.3mm)
9 3/4"
(247.7mm)
10"
(254mm)
9"
(228.6mm)
1"
(25.4mm)

66
Dimensions:
29 7/8" (758.8mm)
28" (711.2mm)
10"
(254mm)
5"
(127mm)
3 1/2"
(90mm)
9 1/2"
(241.3mm)
9"
(228.6mm)
1"
(25.4mm)
10 1/2"
(265.5mm)
32 7/8" (835mm)
31" (787.4mm)
5"
(127mm)
3 1/2"
(90mm)
9 1/2"
(241.3mm) 1"
(25.4mm)
Model #: KWF210-36
Sink Dimensions: 35 7/8” x 20 1/4” x 10”
Min Cabinet Size: 39”
Model #: KWF410-30
Sink Dimensions: 29 7/8” x 20 1/4” x 10”
Min Cabinet Size: 33”
Model #: KWF410-33 & KWF410-33/PGM
Sink Dimensions: 32 7/8” x 20 1/4” x 10”
Min Cabinet Size: 36”
10"
(254mm)
9"
(228.6mm)
10 1/2"
(265.5mm)
20 1/4" (514.4mm)
16" (406.4mm)
17" (431.8mm)
5"
(127mm)
R1/8"
(3mm)
2 1/4"
(57.2mm)
20 1/4" (514.4mm)
16" (406.4mm)
17" (431.8mm)
5"
(127mm)
R1/8"
(3mm)
2 1/4"
(57.2mm)
19 1/2" (495.3mm)
35 7/8" (911.2mm)
34" (863.6mm)
16" (406.4mm)
17" (431.8mm)
5"
(127mm)
5"
(127mm)
3 1/2"
(90mm)
9 1/2"
(241.3mm) 1"
(25.4mm)
10"
(254mm)
9"
(228.6mm)
20 1/4" (514.4mm)
20 1/4" (514.4mm)
35 7/8" (911.2mm)
34" (863.6mm)
16" (406.4mm)
17" (431.8mm)
5"
(127mm)
5"
(127mm)
3 1/2"
(90mm)
9 1/2"
(241.3mm)
R1/8"
(3mm)
2 1/4"
(57.2mm)
1"
(25.4mm)
Model #: KWF410-36
Sink Dimensions: 35 7/8” x 20 1/4” x 10”
Min Cabinet Size: 39”
10"
(254mm)
9"
(228.6mm)
10 1/2"
(265.5mm)

7
Step 1. Determine Reveal Type
·Use scissors to cut along the line of the paper template for your desired reveal type
(Negative, Positive, or Flushed Reveal)
NOTE: Make sure clearance is suitable
for backsplash, faucet and plumbing
for the sink.
Step 2. Position Template
·Check the cut-out template against the actual sink to ensure a proper sized cut-out.
·Place the cut-out template in the desired location on the countertop.
KRAUS Recommended Installation Type
3/8” Positive Reveal
3/8” Positive
Flushed/Zero Reveal
Flushed/Zero
Centerline

8
Step 3. Trace Template
·Trace template on countertop with a pencil.
NOTE: Please use the appropriate saw
that best fits your countertop material.
Step 4. Cut Countertop
·Cut the opening in the countertop by carefully following the traced line.

9
Step 5. Cut Cabinet Front
·Measure height of apron front. Add 1/16" to the dimension when you mark base cabinet front cutout. Use jigsaw to
cut.
1/2"
(13mm)
Step 6. Set Up Mounting Brackets
·Turn countertop over and align sink with countertop. Decide location for mounting brackets.
·Mounting holes should be 1/2" from edge of sink.

10
Step 7. Drill Hole in Countertop
·Drill 3/8" diameter x 1/2" deep hole in the countertop.
3/8 1/2

11
Step 8. Install Anchors
·Insert anchors into drilled holes and lightly tap with a hammer until flush.

Step 9. Secure Sink to Countertop
·Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout
in the countertop. Place sink over cutout hole and press firmly.
12

13
Step 10. Attach Mounting Hardware
·Attach mounting hardware to secure bowl. Remove excess sealant from inside lip.
·Allow sealant to set for 30 - 60 minutes.
NOTE: Use acetone or rubbing alcohol to remove any excess sealant.

14
Step 11. Install Plumbing Fixtures
·Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's
instructions.
·Run water into sink and check for leaks.
·Note: Before installation, please check that the drain kit complies with ASME A112.18.2/CSA B125.2 and with CUPC
certification.

Kitchen Sink Warranty
Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus").
Kraus extends this warranty to the original purchaser for personal household use of the "Kitchen Sink" in its original location. The
warranty is non-transferable.
Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for
the lifetime of the product. The warranty commences from the initial date of purchase by the owner or trade professional, from an
authorized Kraus dealer, through the lifetime of the original owner or end-user.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced
with a product of equal value at the option of Kraus. This warranty extends to the original owner or end-user, and is not transferable
to a subsequent owner.
Restrictions
This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at discount outlets,
unauthorized dealers, and/or sold on clearance.
This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness, accident, hard water or
mineral deposits, exposure to corrosive materials, misapplication, damages caused by improper maintenance, alteration of the
product, or failure to follow care or installation instructions enclosed with your product. Avoid using abrasive cleaners such as
powders, bleach, ammonia, alcohol, or chlorine. Avoid using abrasive pads, steel wool, or wire brushes, as these will damage and
wear down the finish.
This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by Kraus
and all applicable rules, regulations, and legislation pertaining to such installations.
This warranty does not apply unless the Kraus product is installed by a fully insured and licensed trade professional. Kraus insists that
such professionals have experience in the installation of bathroom and kitchen manufactured goods.
This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty does not allow
recovery of incidental or consequential damages, such as loss of use, delay, property damage, or other consequential damages, and
Kraus accepts no liability for such damages.
This warranty does not cover Marine or Outdoor Installation.
This warranty does not cover any free gifts included with purchase.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and
fitness for a particular purpose, or compliance with any code.
Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping
charges may apply). International shipping fees are not included.
COMMERCIAL WARRANTY
Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and
business use.
All incidental or consequential damages are specifically excluded. No additional warranties, express or implied, are given,
including but not limited to any implied warranty of merchantability or fitness for a particular purpose.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
KRAUS USA has the right to change, modify, and/or update the warranty policy at any time. For the latest, most up to date
comprehensive warranty, go to www.kraususa.com/warranty
Codes/Standards Applicable
15
UPC
CR

16
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]
If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
[email protected]
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
[email protected]
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance

Register Your Kraus Product
Activate Your Warranty
Access Premium Customer Support
Get Product Information
REGISTER TODAY
http://www.kraususa.com/registration
IMPORTANT
R
www.kraususa.com