Kraus KWT300-32 User manual

KWT300-32
Kore Workstation Stainless
Steel Dual Mount Kitchen Sink
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. October 26, 2020
R
INSTALLATION MANUAL

2
Congratulations on the purchase of your new Kraus plumbing fixture!
Please keep the box and packaging materials until your product is completely installed. If you have
any questions, require technical assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt with purchase date for
reference.
If for any reason this product does not meet your expectations, please be sure to repack this
product in the original box and packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

3
For technical assistance or replacement parts, please contact Kraus Customer Service
and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus sink. Should
there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a
licensed professional.
Prior to Installation:
·Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact Kraus Customer Service at
800-775-0703 for a replacement
·Inspect the sink prior to installation to make sure that it has not been
damaged or during shipping
·Use the cut-out template provided by Kraus
·Observe all plumbing and building codes according to your state
requirements
Parts List:
Sink KWT300-32
Strainer ST-1
Cover Cap STC-2
Bottom Grid KBG-WST1-32
Cutting Board KCB-WS105BB
Colander CS-7
Cut-Out Template
Mounting Hardware
Soap Dispenser Hole Cap

44
Tools you will need:
NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen sinks with
countertop materials other than wood, marble or granite.
Safety Goggles Silicone Adhesive Jig Saw Phillips Screwdriver
Putty Knife Tape Measure Pencil Scissors Screwdriver
Drill
Dimensions:
Model #: KWT300-32
Sink Dimensions: 31 1/4” x 20 1/2” x 9”
Min Cabinet Size: 33”
15 1/4" (387mm)
20 1/2" (520.7mm)
31 1/4" (793.8mm)
28 1/2" (723.9mm)
3 7/8"
(98.8mm)
9"
(228.6mm)
1 3/8"
(35mm)
2 1/4" (57mm)
4 3/4"
(120.7mm)
13 7/8" (351mm)
3/4"
(18mm)
3 1/2"
(89mm)
Ø1 3/8"
(35mm)
R 3/8"
(10mm)
3 1/2"
(90mm)

55
Topmount Installation
Step 1. Position Template
·Check the cut-out template against the actual sink to ensure a proper
sized cut-out.
·Place the cut-out template in the desired location on the countertop.
NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink.
Step 2. Trace Template
·Trace template on countertop with a pencil.
Paper Template
Paper Template

66
Step 3. Cut Countertop
·Cut the opening in the countertop by carefully following the traced line.
NOTE: Please use the appropriate saw that best fits your countertop material.

7
Step 4. Attach Mounting Hardware
·Attach mounting hardware to the prongs protruding from the underside of the sink rim.
·Make sure the hooked side of the mounting clip is facing away from the sink.
Insert

8
Step 5. Apply Silicone or Plumber's Putty
·Clean and dry the surface around the opening of the sink.
·Turn the unit upside down to apply sealant. Apply silicone-based sealant (not included) underneath the edge of the
sink.

9
Step 6. Secure Sink to Countertop
• Insert the sink into the opening, check the alignment of the sink to the cutout in the countertop and press firmly.
• Tighten the screws in the front of the sink, followed by the ones in the back and on the sides of the sink.
• Remove excess silicone-based sealant.
· Allow sealant to set for 30-60 minutes.
Sealant or Putty
Sink Countertop
Fasten the Screw

10
Step 7. Install Plumbing Fixtures
·Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's
instructions.
·Run water into sink and check for leaks.
·Note: Before installation, please check that the drain kit complies with ASME A112.18.2/CSA B125.2 and with CUPC
certification.