Kraus Arqo M KPF-2523 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. August 27, 2019
Arqo M Pull Down
Kitchen Faucet
KPF-2523
R
INSTALLATION MANUAL
TM

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
Clean sink or countertop to remove any debris, plumber’s putty, or
silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min) - 1 1/2" (max)
·Max countertop thickness: 2 1/2”
·1 or 3 hole installation
3
Tools Required
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
Adjustable Wrench Phillips Screwdriver Silicone Sealant
Safety Goggles Bucket

44
Diagram and Parts List
A. Spray Head
B. Faucet Body
C. Base O-Ring
D. Deck Plate Assembly
E. Mounting Hardware
E1. Rubber Washer
E2. Metal Washer
A
B
K
L
C
F
D1
J
I
E4
E3
E2
E1
D2
G
H
E3. Mounting Nut
E4. Mounting Screws
F. Spray Hose
G. EZ-Connect
H. EZ-Weight
I. Supply Hose
J. Hot & Cold Waterlines
K. Aerator Key
L. Hex Wrench
M. 2.2 GPM Flow
Restrictor (WHITE)
M

55
Faucet Installation Procedure
Installer Tip:
Shut off main water supply before installing new faucet.
11.9°
Ø2 1/4"
(55.93mm)
10 1/2"
(280.31mm)
8 5/8"
(219.16mm)
11"
(280.31mm)
9"
(228.9mm)
17 3/4"
(451.74mm)
8 1/4"
(209.6mm)
MAX.
2 1/2"
(63.5mm)
1 3/8”~1 1/2”
(35~38 mm)

66
Step 1. Remove mounting hardware
Step 2A. Install the faucet assembly (with deckplate)
Shut off the water supply.
Remove the old faucet. Clean
the mounting surface. Remove
mounting hardware (E) from
faucet body (B).
Insert the faucet assembly (B)
through the hole in the deck plate
assembly (D).
NOTE: Skip this step if installing
without deckplate.B
C
D2
D1
E1
E4
E3
E2
B

7
Step 2B. Install the faucet assembly (without deckplate)
For single-hole installation, deck
plate assembly (D) and silicone
sealant are NOT required.
Step 3. Secure the faucet assembly
Insert faucet body (B) into hole on
countertop or deck plate
assembly (D) with base o-ring (C)
attached. Attach mounting
hardware (E).
B
C
D2
D1
E2
E1
E4
E3
B
C

8
Step 4. Secure the faucet assembly
Adjust faucet body (B). Tighten
mounting nut (E3) with wrench
and mounting screws (E4) with
Phillips head screwdriver.
E3 E4
Step 5. Attach spray hose and counterweight
Connect spray hose (F) to quick
connector (G) attached to supply
line. Install weight (H) on lowest
vertical point on spray hose (F).
B
G
F
H

9
Step 6. Connect waterlines
Thread hot & cold waterlines (J)
onto angle stops. Tighten with
adjustable wrench until snug. Turn
on the angle stops and check for
leaks.
(DO NOT TURN FAUCET ON)
Step 7. Flush spray hose
Remove spray head (A). Hold tip of
spray hose (F). Turn faucet on for 1
minute to flush any debris.
J
F
A

10
Press
Step 8. Attach spray head
Attach spray head (A) to spray
hose (F).
Step 9. Check spray head
Turn faucet on. Press rocker switch
to check if spray head (A) switches
modes properly.
F
A
Press

11
NOTE: In compliance with CEC standards, this faucet is designed with a 1.8 gpm
flow rate. At your discretion, you may modify the product with the included 2.2
gpm restrictor. Please note that doing so will remove the capability of this product
to meet specific low-flow standards. Kraus is not liable for any alterations made to
the product post-sale, and highly advises that you consult with your local or
statewide plumbing enforcement agency prior to any modification.
2
11
1
2
Step 10. Flow regulator replacement
This faucet ships with a 1.8 GPM
flow restrictor installed. An
optional 2.2 GPM flow restrictor is
also included in the box.
To switch the flow rate of the
faucet:
1. Disassemble the quick connect
assembly by separating the
connector (1) (Black) and quick
connect (2) (White) using an
adjustable wrench.
2. Replace 1.8 GPM connector
(Black) with the 2.2 GPM
connector (White).
3. Reinstall the quick connect
assembly.

12
Replacement Parts
*Denotes faucet component color
options:
SFS - Spot Free Stainless Steel
MB - Matte Black
BL - Black
WH - White
2
1B
1A 3
4
5
7
8
13
11
10
9
6
16
KP26019
KP26055
KP26056
KP26020
KP26059
KP26052
10. Escutcheon
11. Mounting Hardware
12. Washer
13. Spray Hose
14. 2.2GPM Flow Restrictor
15. 1.8GPM Flow Restrictor
16. EZ-Connect
17. EZ-Weight
18. Aerator Key
19. Hex Wrench
20. Filter Washers
WH*
Replacement Parts List Finish/ Part #
Color
Replacement Parts List Finish/ Part #
Color
KP26000
KP26002
KP26003
KP26007
KP26008
KP26009
KP26010
KP26054
SFS,MB*
1A. Aerator
1B. Spray Head
2. O-ring
3. Spout Clip
4. Handle Assembly
5. Cartridge Cover
6. Locking Nut
7. Cartridge
8. Base O-ring
9. Hose Clip
KP26001
SFS,MB* KP26057
KP26022
KP26058
12
KP26053
17
14
15
SFS,MB*
SFS,MB*
BL*
KP26027
20
KP26060
19
18

13
Trouble-Shooting
If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:
Leakage under the handle Locking nut has come loose Remove cap. Loosen set screw with a hex
wrench. Remove the handle and unscrew
cartridge cover by hand. Tighten locking
nut with an adjustable wrench.
Leaking between spray head
and hose.
Spray head may be loose, or washer
may not be seated correctly in hose
Tighten spray head by hand until snug.
Make sure washer is seated correctly.
Care & Maintenance
To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
This installation manual is subject to change without further notice.
Water will not shut off completely Cartridge may be defective Remove cap. Loosen set screw with a hex
wrench. Remove the handle and unscrew
cartridge cover by hand. Unscrew the
locking nut with an adjustable wrench.
Remove ceramic disc cartridge. Check for
cracks.
ACID
PROBLEM CAUSE ACTION
The water pressure is low. EZ-Connect (21) may be clogged with
debris
Remove EZ-Connect from supply hose and
spray hose. Soak quick connect in vinegar
& warm water 50/50 solution for 5 - 10
minutes.
Hose does not retract Weight may be installed incorrectly Readjust weight on hose.

FAUCET WARRANTY
Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus").
Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location.
The warranty is non-transferable.
Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal
usage for the lifetime of the product. The warranty commences from the initial date of purchase by the owner or trade
professional, from an authorized Kraus dealer, through the lifetime of the original owner or end-user.
Kraus warrants the mechanical components such as but not limited to sprayhead assembly (includes engine, aerators,
structure, restrictors, back flow preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon
and stainless steel,etc) of the product to be free from defects in material and workmanship under normal usage for a
period of one (1) year. The warranty commences from the initial date of purchase by the owner or trade professional,
from an authorized Kraus dealer, through the one (1) year term of the original owner or end-user.
Kraus warrants the mechanical component (cartridge) of the product to be free from defects in material and
workmanship under normal usage for a period of five (5) years. The warranty commences from the initial date of
purchase by the owner or trade professional, from an authorized Kraus dealer, through the five (5) year term of the
original owner or end-user.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired
or replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or end-user,
and is not transferable to a subsequent owner.
RESTRICTIONS
This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at
discount outlets, unauthorized dealers, and/or sold on clearance.
This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness, accident, hard
water or mineral deposits, exposure to corrosive materials, misapplication, damages caused by improper maintenance,
alteration of the product, or failure to follow care or installation instructions enclosed with your product. Avoid using
abrasive cleaners such as powders, bleach, ammonia, alcohol, or chlorine. Avoid using abrasive pads, steel wool, or wire
brushes, as these will damage and wear down the finish.
This warranty does not apply to Products that have not been installed or operated in accordance with instructions
supplied by Kraus and all applicable rules, regulations, and legislation pertaining to such installations.
This warranty does not apply unless the Kraus product is installed by a fully insured and licensed trade professional.
Kraus insists that such professionals have experience in the installation of bathroom and kitchen manufactured goods.
This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty does not
allow recovery of incidental or consequential damages, such as loss of use, delay, property damage, or other
consequential damages, and Kraus accepts no liability for such damages.
This warranty does not cover Marine or Outdoor Installation.
Codes/Standards Applicable:
14
UPC
CR
UPC
CR
NSF/ANSI 372 NSF/ANSI 61-9
ASME A112.18.1
1.8GPM 6.8L/min maximum

Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of
merchantability and fitness for a particular purpose, or compliance with any code.
Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto
Rico shipping charges may apply). International shipping fees are not included.
COMMERCIAL WARRANTY
Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and
business use.
All incidental or consequential damages are specifically excluded. No additional warranties, express or implied, are given,
including but not limited to any implied warranty of merchantability or fitness for a particular purpose.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
KRAUS USA has the right to change, modify, and/or update the warranty policy at any time. For the latest, most up to
date comprehensive warranty, go to www.kraususa.com/warranty
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]
If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
[email protected]
If you are an Authorized Partner please contact a Partner Support Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
[email protected]
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
15

Register Your Kraus Product
Activate Your Warranty
Access Premium Customer Support
Get Product Information
REGISTER TODAY
http://www.kraususa.com/registration
R
www.kraususa.com
IMPORTANT