Kraus FC-100PP User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2021 Kraus USA Plumbing LLC I REV. May 17, 2022
Replacement Filter
Cartridges
FC-100PP and FC-100CB
For use with FS-1000 System
R
INSTALLATION MANUAL

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP
R

3
Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Read all instructions and safety warnings and ensure you have all
tools, parts, and equipment necessary for a safe installation.
·Observe all state and local plumbing and building codes.
·! CAUTION - Make sure to only install this filtration system to the cold
water supply. To reduce the risk of personal injury, do not install the
system to the hot water supply.
·IMPORTANT - Replace the filter cartridges every 6 months or when the
700 gallon capacity has been exceeded, whichever comes first. You
may also need to replace if you notice a decrease in water flow. The
failure to follow this instruction may affect product performance and
void the warranty.
·IMPORTANT - Flush the system for 30 minutes prior to first use and 5
minutes after prolonged periods of nonuse. The failure to follow this
instruction may affect product performance and void the warranty.
·NOTE: Make sure to mark the installation date on the filter head and
cartridges for your reference.
Installation and use must comply with all state and local laws, regulations and
codes.
! CAUTION - To avoid the risk of personal injury, the system is to be
supplied only with cold water.
STOP

44
Bucket Rags
* To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth.
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners
as use of such products may affect product performance or void the warranty.
3. Do not use cloth with a coarse surface.
4. Unscrew the aerator and rinse clean when necessary.
ACID
Materials Required
Care & Maintenance

55
Specifications
Diagram and Parts List
1. Polypropylene Cartridge
2. Compressed Carbon Cartridge
12
Flow Rate 0.7GPM
NOTE: Depending on local water quality and use environment, the actual filtered
water flow rate and total filtered water volume will vary.
Capacity = 700 gallons
Min static pressure: 40 psi (275.8 kPa)
Max static pressure: 120 psi (827.4 kPa)
Inlet Water Temperature 41° - 100° F
! CAUTION - Do not use with water that is micro biologically unsafe or of unknown
quality without adequate disinfection before or after the system.

66
Step 1.
Remove the existing filter cartridge.
Place a bucket under the filtration
system to catch any dripping water.
Rotate the cartridge 90° clockwise
and pull down to remove. Throw out
the used cartridge.

7
Step 2.
Install the filter cartridges. Write the
date on the new filter cartridge label.
Remove the cap from the filter
cartridge and discard. Inspect the
cartridge for any damage. Make sure
both sets of O-rings are present and
are positioned correctly. Align the
filter cartridge as shown and press
upward into the filter head. Rotate
the filter cartridge counterclockwise
90° until it is secure in the filter head.
Repeat for the second cartridge.
IMPORTANT: The Polypropylene
Cartridge must be on the left side.
The Compressed Carbon Cartridge
must be on the right side below the
LCD screen.
IMPORTANT: Replace cartridges at
the same time to maintain a proper
performance.
Cap
O-rings
Step 3.
Turn on the cold water supply valve
and check all connections for leaks.
Run the water for at least 5 minutes
to remove any air and carbon
particles in the system.

Step 4.
Display & Reset:
After installing new filters push and hold the settings button for 3 seconds. Filter 1 icon will
blink. Push the reset button and hold for 3 seconds and the icon will reset to full capacity. Push
the settings button again and filter 2 icon will blink. Push and hold the reset button for 3
seconds and the icon will reset to full capacity. Push the settings button to exit the reset mode.
Flush:
When installing new filters, you must flush for a minimum of 30 minutes, the flush icon will blink
until done. If filters have not been used for more than 3 days, the flush icon will blink. Flush for
a minimum of 30 minutes.
Potable Water Icon:
The Potable Water icon will blink when the filter is ready for use.
! CAUTION - Do not drink the water before the Potable Water icon blinks.
Filter Icon:
The Filter Icon represents the 2 filters for the FF-1000 filter unit. Indication
of 5 bars show a new filter, 100% capacity, 4 bars 50-75%
capacity, 3 bars 25-50% capacity, 2 bars 5-25% capacity,
1 bar less than 5% capacity. When below a 5% capacity the Filter Icon
will blink, and the unit will buzz every 6 seconds when the water is flowing.
At 0% filter capacity the icon will blink constantly.
Battery Icon:
When the batteries reach below 10% capacity the
Battery Icon will blink and a warning light will come on.
Cleaning in Progress Icon:
The conditions that initiate the cleaning process are when the filter has not been used for three
days or after the filters are replaced. If any of the two conditions are met, the "cleaning" starts.
The "Cleaning in Process" icon starts to blink. The cleaning takes ten minutes. It stops blinking
after ten minutes when the cleaning is completed.
Potable Water
Replace Filter Soon
Cleaning in Progress
1
!
2
Filter Icon
0% Capacity
Battery Icon
Full
Battery
Low
Battery
Settings Button
Reset Button
8

9
Troubleshooting
If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:
Water leaks between the
filter head and the filter cartridge. An O-ring is damaged, dirty, or
out of place.
Turn off the water supply, and relieve
water pressure. Remove the filter
cartridge and inspect the O-rings for
damage or debris, and ensure that the
O-rings are in place. Reinstall the filter
cartridge, turn on the water supply, and
check for water leakage.
Water leaks at a threaded
connection.
The connection is
damaged or dirty.
Turn off the water supply, and relieve
water pressure. Disconnect the fitting, and
inspect the seal for damage or debris.
Remove any debris or replace the
damaged fitting. Securely reconnect the
fitting.
IMPORTANT - DO NOT overtighten.
Turn on the water supply and check for
leakage.
Water leaks at a tubing
connection.
Tubing is not cut square, or is
damaged or crimped.
Turn off the water supply, and relieve
water pressure. Remove the Quick Connect
Lock Tab. Press in the collar around
the fitting at the leak, and pull the tubing
to remove. Use a sharp utility knife to
cut 1/2″ (13 mm) off the end of the
tubing. Reinsert the tubing into the
fitting. Turn on the water supply and
check for leakage.
PROBLEM CAUSE ACTION

10
Replacement Parts
2. Polypropylene Cartridge
Replacement Parts List Part #
KF-1CB
KF-1PP
1. Compressed Carbon Cartridge
12

11
Performance Data Sheet
Substance Influent Challenge Minimum % Reduction or Maximum
Concentration mg/L Product Water Concentration Requirement mg/L
alachlor
atrazine
benzene
carbofuran
dibromochloropropane (DBCP)
chlorobenzene
chloropicrin
carbon tetrachloride
2,4-D
0.050
1,1-dichloroethylene
o-dichlorobenzene
p-dichlorobenzene
1,2-dichloroethane
cis-1,3-dichloropropylene
cis-1,2-dichloroethylene
trans-1,2-dichloroethylene
1,2-dichloropropane
ethylene dibromide (EDB)
dinoseb
endrin
ethylbenzene
heptachlor epoxide
heptachlor
methoxychlor
hexachlorobutadiene
hexachlorocyclopentadiene
lindane
styrene
pentachlorophenol
simazine
2,4,5-TP (silvex)
1,1,2,2-tetrachloroethane
tetrachloroethylene
toluene
1,1,2-trichloroethane
tribromoacetic acid
1,2,4-trichlorobenzene
1,1,1-trichloroethane
trichloroethylene
xylenes (total)
trihalomethanes (includes)
chloroform (surrogate chemical)
bromoform
bromodichloromethane
chlorodibromomethane
haloacetonitriles (HAN)
bromochloroacetonitrile
dibromoacetonitrile
dichloroacetonitrile
trichloroacetonitrile
haloketones (HK)
1,1-dichloro-2-propanone
1,1,1-trichloro-2-propanone
0.001
0.100 0.003
0.081 0.001
0.190 0.001
0.078 0.0018
0.077 0.001
0.015 0.0002
0.110 0.0017
0.052 0.00002
0.080 0.001
0.040 0.001
0.088 0.0048
0.083 0.001
0.170 0.0005
0.086 0.001
0.080 0.001
0.079 0.001
0.170 0.0002
0.053 0.00059
0.088 0.001
0.044 0.00002
0.0072 0.0001
0.0082 0.0003
0.025 0.00001
0.0107 0.0002
0.044 0.001
0.060 0.000002
0.055
0.00010.050
0.0010.096
0.0040.120
0.00050.150
0.0010.081
0.0010.081
0.0016
0.078
0.001
0.270
0.0005
0.042
0.0046
0.160
0.0005
0.084
0.150
0.180 0.001
0.300 0.015
0.070 0.001
0.0096 0.0002
0.015 0.0003
0.022 0.0005
0.024 0.0006
0.001
0.00001
This system has been tested according to NSF/ANSI 42, 53 and 401 for reduction of the substances listed below.
The concentration of the indicated substances in water entering the system was reduced to a concentration less
than or equal to the permissible limit for water leaving the system as specific in NSF/ANSI 42, 53 and 401.

All-in-One Filtration Set - Limited Warranty
Kraus USA Plumbing, LLC extends this warranty to the original consumer and commercial purchasers of the All-in-One
Filtration Set (the “Product”) when purchased from an authorized Kraus dealer and in the location of original installation.
This warranty is non-transferable.
Kraus warrants the structure and finish of the Product to be free from defects in material and workmanship under normal
usage for a period of one (1) year from the date of purchase by a trade professional or end-user of the Product from an
authorized Kraus dealer.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired
or replaced with a product of equal value at the option of Kraus.
Care Instructions
The filters must be replaced every six (6) months or when the 700 gallon capacity has been exceeded, whichever comes
first. You may also need to replace if you notice a decrease in water flow.
What is Not Covered
This warranty does not cover Products that were discontinued when purchased or display Products, whether such
Products were purchased at discount outlets, unauthorized dealers, and/or sold on clearance. This warranty does not
cover any free gifts included with purchase.
This warranty does not cover damage resulting from neglect, misuse (including use for an unintended application),
abuse, carelessness, accident, hard water or mineral deposits, exposure to corrosive materials, improper maintenance,
alteration of the Product, failure to follow care, cleaning or installation instructions enclosed with your Product. Kraus
recommends that all Kraus Products be installed by a fully licensed and insured trade professional with experience in the
installation of bathroom and/or kitchen manufactured goods.
Codes/Standards Applicable:
UPC
R
The filters are certified by IAPMO R&T according to NSF/ANSI 42 standard for material safety, structural
integrity, chlorine, particulate I; NSF/ANSI 53 standard for Lead, VOC and PFOA/PFOS reduction; NSF/ANSI 401
standard for Bisphenol A,Phenytoin, Ibuprofen, Naproxen,Estrone, Nonylphenol, and NSF/ANSI 372 for low
lead compliance when used in FS-1000. See Performance Data Sheet for individual contaminants and
reduction performance.
The FS-1000 system conforms to NSF/ANSI 42, 53, 401 and 372 for the specific performance claims as verified
and substantiated by test data. The filters themselves are not certified except for when used with the certified
system.
While testing was performed under standard laboratory conditions, actual performance may vary.
R
12

How to Make a Warranty Claim
If you are a consumer purchaser, please contact a Kraus Customer Service Representative at:
Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]
If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at:
Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
[email protected]
If you are an authorized partner, please contact a Partner Support Representative at:
Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
[email protected]
In requesting warranty service, please be ready to provide your proof of purchase and a description of the problem.
Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto
Rico shipping charges may apply). International shipping fees are not included.
Limitation on Duration of Implied Warranties
Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty
lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A
PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS
SHORTER.
Limitation of Special, Incidental or Consequential Damages
Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental
or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND KRAUS USA PLUMBING, LLC SHALL NOT BE
LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR,
REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to
state/province.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
R
13

Register Your Kraus Product
Activate Your Warranty
Access Premium Customer Support
Get Product Information
REGISTER TODAY
http://www.kraususa.com/registration
R
www.kraususa.com
IMPORTANT
R