KROHNE 1000 Series Wiring diagram

1000 / 2000 / 3000 / 6000 / 7000 series of meters and
MFC 400 converter
Hazardous areas
Hazardous areasHazardous areas
Hazardous areas
OPTIMASS / 400
OPTIMASS / 400OPTIMASS / 400
OPTIMASS / 400
Supplementary Instructions
Supplementary InstructionsSupplementary Instructions
Supplementary Instructions
© KROHNE 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 1 Thursday, February 4, 2021 12:19 PM

CONTENTS
2
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
OPTIMASS / 400
1 Introduction 4
1.1 General ............................................................................................................................. 4
1.2 EN standards compliance ................................................................................................ 4
1.3 Hazardous areas approvals.............................................................................................. 4
1.4 Identification of OPTIMASS flowmeter systems .............................................................. 5
1.5 Flow sensor VE code........................................................................................................ 6
1.6 Flow converter VE code.................................................................................................... 7
1.7 MFC 400F.......................................................................................................................... 8
1.8 OPTIMASS 1000F / 1400C................................................................................................. 9
1.9 OPTIMASS 2000F / 2400C............................................................................................... 10
1.10 OPTIMASS 3000F / 3400C............................................................................................. 11
1.11 OPTIMASS 6000F / 6400C............................................................................................. 12
1.12 OPTIMASS 7000F / 7400C............................................................................................. 14
1.13 Nameplates .................................................................................................................. 15
2 Special Conditions 16
2.1 Equipotential bonding..................................................................................................... 16
2.2 Electrostatic charge .......................................................................................................16
2.3 Converter orientation (compact version) ....................................................................... 16
2.4 Temperature limits.........................................................................................................17
2.4.1 Introduction........................................................................................................................... 17
2.4.2 MFC 400F .............................................................................................................................. 17
2.4.3 OPTIMASS 1000F / 1400C ..................................................................................................... 18
2.4.4 OPTIMASS 2000F / 2400C ..................................................................................................... 19
2.4.5 OPTIMASS 3000F / 3400C ..................................................................................................... 20
2.4.6 OPTIMASS 6000F / 6400C - standard temperature ("j" = K & "q"
≠ T) ................................ 21
2.4.7 OPTIMASS 6000F / 6400C - short stem ("j" = 0) ................................................................... 23
2.4.8 OPTIMASS 6000F high temperature ("q" = T)....................................................................... 25
2.4.9 OPTIMASS 7000F / 7400C ..................................................................................................... 27
2.4.10 Painted options ................................................................................................................... 28
2.5 Electronics compartment............................................................................................... 28
2.6 Certified cable glands.....................................................................................................29
2.7 Cable protection ............................................................................................................. 29
2.8 Aluminium junction box.................................................................................................. 29
3 Electrical connections 30
3.1 Remote / field terminal connections.............................................................................. 30
3.1.1 Separated systems ............................................................................................................... 31
3.1.2 Cable parameters ................................................................................................................. 31
3.2 Electronics and I/O terminal compartments ................................................................. 32
3.2.1 I/O terminal compartment.................................................................................................... 32
3.2.2 Converter VE code for I / O options....................................................................................... 33
3.2.3 Converter VE code I / O overviews........................................................................................34
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 2 Thursday, February 4, 2021 12:19 PM

CONTENTS
3
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
OPTIMASS / 400
4 Service 39
4.1 General ........................................................................................................................... 39
4.2 Replacing the power supply fuse ................................................................................... 39
4.3 Returning the device to the manufacturer..................................................................... 40
4.3.1 General information.............................................................................................................. 40
4.3.2 Form (for copying) to accompany a returned device............................................................ 41
4.3.3 Disposal................................................................................................................................. 41
5 Notes 42
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 3 Thursday, February 4, 2021 12:19 PM

1INTRODUCTION
4
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
Introduction
1.1 General
The OPTIMASS flowmeter system consists of a mass flow sensor and a flow converter, or a mass
flow sensor and associated equipment.
The separate mass flow sensor with a mass flow converter is identified as:
•OPTIMASS 1000F flow sensor with MFC 400F flow converter
•OPTIMASS 2000F flow sensor with MFC 400F flow converter
•OPTIMASS 3000F flow sensor with MFC 400F flow converter
•OPTIMASS 6000F flow sensor with MFC 400F flow converter
•OPTIMASS 7000F flow sensor with MFC 400F flow converter
The flowmeter in a compact configuration is identified as:
•OPTIMASS 1400C (OPTIMASS 1000 + MFC 400)
•OPTIMASS 2400C (OPTIMASS 2000 + MFC 400)
•OPTIMASS 3400C (OPTIMASS 3000 + MFC 400)
•OPTIMASS 6400C (OPTIMASS 6000 + MFC 400)
•OPTIMASS 7400C (OPTIMASS 7000 + MFC 400)
The OPTIMASS x000 is the general terminology for the OPTIMASS x000F
1.2 EN standards compliance
As part of the hazardous areas approval, the OPTIMASS flowmeter system satisfies the
requirements of the following standards:
•BS EN 60079-0:2012+A11:2013 - Explosive atmospheres. Equipment. General requirements
•BS EN 60079-1:2014 - Explosive atmospheres. Equipment protection by flameproof
enclosures "d"
•BS EN 60079-7:2015 - Explosive atmospheres. Equipment protection by increased safety "e"
•BS EN 60079-11:2012 - Explosive atmospheres. Equipment protection by intrinsic safety "i"
•BS EN 60079-26:2015 - Explosive atmospheres. Equipment with Equipment Protection Level
(EPL) Ga
•BS EN 60079-31:2014 - Explosive atmospheres. Equipment dust ignition protection by
enclosure "t"
1.3 Hazardous areas approvals
The hazardous areas approvals for the OPTIMASS flowmeter system, relating to this
supplementary manual, are as follows:
•ATEX - PTB12 ATEX 2013X, PTB12 ATEX 2014X and PTB12 ATEX 2015X
•IECEx - PTB 12.0041X, PTB 12.0042X and PTB 12.0043X
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 4 Thursday, February 4, 2021 12:19 PM

INTRODUCTION 1
5
OPTIMASS / 400
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.4 Identification of OPTIMASS flowmeter systems
The complete OPTIMASS flowmeter system is identified by the models of the flow sensor and the
flow converter.
The VE codes are unique and are used to identify the models and variants of the OPTIMASS flow
sensor and flow converter and therefore the complete flowmeter system; through the original
order specification and manufacture of the system. The VE code for each flowmeter system is
included on the product nameplate/s. Please refer to the nameplates section.
On integral / compact systems, where the converter is mounted directly to the sensor, the
nameplate is on the converter housing. On remote systems, where the converter housing is
separate to the sensor and linked by a dedicated cable, the nameplate is on the remote converter
housing and essential data is duplicated on the junction box of the sensor.
Not all elements of the VE codes are Ex safety relevant. The following tables describe the VE
code structure and defines the hazardous area relevant options.
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 5 Thursday, February 4, 2021 12:19 PM

1INTRODUCTION
6
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.5 Flow sensor VE code
The flow sensor variant is identified by the VE code number on the nameplate:
1
VE ab c d e fg h j k l m n p q r s t u v w
2
1-2 3-4 5678-9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
3
x√xxxxxx√ √ x√xxx√ √ x x x
1Code
2Position
3Hazardous areas relevant?
Code Description
VE Prefix to code
ab Flow sensor type and size
cManufacturer specific
dWetted part material
eSurface finish
fg Flange size and rating
hFlange sealing face
jOuter case material / secondary containment / operating pressure
kOptions
lHazardous area approval
mSanitary and material approvals
nConfiguration
pCalibration
qCleaning / degreasing / process requirements
rExtended options / custody transfer approval
s"0"
tConverter type
uDestination
vFunctional safety
w Spare
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 6 Thursday, February 4, 2021 12:19 PM

INTRODUCTION 1
7
OPTIMASS / 400
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.6 Flow converter VE code
The flow converter variant is identified by the VE code number on the nameplate:
1
VE ab c d e f g h j k l m n p q r s t u v w
2
1-2 3-4 5678910 11 12 13 14 15 16 17 18 19 20 21 22 23
3
x√x√√√xxxxx√√√√xx√x x x
1Code
2Position
3Hazardous areas relevant?
Code Description
VE Prefix to code
ab Converter type 1
cManufacturer specific
dType
epower supply
fHazardous areas approval
gCable connection
hLanguages
jCustody transfer
kProcess diagnostics
lConverter housing
m"0"
nOutputs (base I/O module)
pOutputs (first I/O module)
qOutputs (second I/O module)
rmeasuring functions
sManuals
tRemote option: signal cable
uDestination
vSensor type
w Spare
153 refers to MFC 400 and 54 refers to MFC 400S
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 7 Thursday, February 4, 2021 12:19 PM

1INTRODUCTION
8
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.7 MFC 400F
The MFC 400F is defined by the VE code VE5b…d…f…npq…where “f”defines the hazardous
area approval and "b" = 3 or 4 and “d”= H
The MFC 400F has intrinsically safe connections to the mass flow sensor with either increased
safety or intrinsically safe signal outputs. The signal output connection compartment can be
configured with protection type Ex d or Ex e. The marking is as follows:
Ex i outputs (where the VE code VE5b...d...f...npq and "n" = 2, 3, D or E and "p" = 0, 1 or 2)
Ex d connection compartment
1 II 2 (1) G Ex db [ia Ga] IIC T6 Gb
II 2 (1) D Ex tb [ia Da] IIIC T75°C Db
Ex e connection compartment 2 II 2 (1) G Ex db eb [ia Ga] IIC T6 Gb
II 2 (1) D Ex tb [ia Da] IIIC T75°C Db
Non Ex i outputs (where the VE code VE5b...d...f...npq and "n" ≠2, 3, or "n" = D or E and "p" ≠0, 1 or 2)
Ex d connection compartment
1 II 2 G Ex db [ia] IIC T6 Gb
II 2 D Ex tb IIIC T75°C Db
Ex e connection compartment 2 II 2 G Ex db eb [ia] IIC T6 Gb
II 2 D Ex tb IIIC T75°C Db
1Where "f" = 1
2Where "f" = 2
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 8 Thursday, February 4, 2021 12:19 PM

INTRODUCTION 1
9
OPTIMASS / 400
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.8 OPTIMASS 1000F / 1400C
The OPTIMASS 1000F is defined by the sensor VE code VEab…k…l…n…where “l”defines the
hazardous area approval, “ab”= 83, 84, 85 or 860H, 01, 1H or 02 and “n”= 1 or 2
The OPTIMASS 1400C is defined by the sensor VE code VEab…k…l…n…, where “l”defines the
hazardous areas approval, “ab”= 83, 84, 85 or 860H, 01, 1H or 02 and “n”= 0
The markings for the OPTIMASS 1000F / 1400C are shown in the following tables:
OPTIMASS 1000F with ("k" = 1 or 2) or without ("k" = 0 or 3) heating jacket / insulation
Intrinsically safe II 1 G Ex ia IIC T6...T1 Ga
II 1 D Ex ia IIIC T185°C Da
OPTIMASS 1400C Non Ex i signal outputs (where the converter VE code VE5b…f…npq…and n ≠2 or 3, or
n = D or E when “p”≠0, 1 or 2) with (“k”= 1 or 2) or without (“k”= 0 or 3) sensor heating jacket / insulation
(“k”is from the sensor VE code )
Ex d connection compartment
1 II 1/2 G Ex db ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T185°C Db
Ex e connection compartment 2 II 1/2 G Ex db eb ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T185°C Db
OPTIMASS 1400C Ex i signal outputs (where the converter VE code VE5b…f…npq…and “n”= 2, 3, D or E
and “p”= 0, 1 or 2) with (“k”= 1 or 2) or without (“k”= 0 or 3) sensor heating jacket / insulation. (“k”is from
the sensor VE)
Ex d connection compartment
1 II 1/2 (1) G Ex db ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T185°C Db
Ex e connection compartment 2 II 1/2 (1) G Ex db eb ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T185°C Db
1Where "f" = 1 from the converter VE code
2Where "f" = 2 from the converter VE code
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 9 Thursday, February 4, 2021 12:19 PM

1INTRODUCTION
10
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.9 OPTIMASS 2000F / 2400C
The OPTIMASS 2000F is defined by the sensor VE code VEab…k…l…n…where “l”defines the
hazardous areas approval, “ab”= 87, 88, 89 or 90 and “n”= 1 or 2
The OPTIMASS 2400C is defined by the sensor VE code ab…k…l…n…where “l”defines the
hazardous areas approval, “ab”= 87, 88, 89 or 90 and “n”= 0
The marking for the the OPTIMASS 2000F / 2400C is shown in the following tables:
OPTIMASS 2000F with ("k" = 1, 2, C or D) or without ("k" = 0, 3 or B) heating jacket / insulation
Intrinsically safe II 1 G Ex ia IIC T6...T1 Ga
II 1 D Ex ia IIIC T160°C Da
OPTIMASS 2400C Non Ex i signal outputs (where the converter VE code VE5b…f…npq…and n ≠2 or 3, or
n = D or E when “p”≠0, 1 or 2) with (“k”= 1, 2, C or D) or without (“k”= 0, 3 or B) sensor heating jacket /
insulation (“k”is from the sensor VE code)
Ex d connection compartment
1 II 1/2 G Ex db ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T160°C Db
Ex e connection compartment 2 II 1/2 G Ex db eb ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T160°C Db
OPTIMASS 2400C Ex i signal outputs (where the converter VE code VE5b…f…npq…and “n”= 2, 3, D or E
and “p”= 0, 1 or 2) with (“k”= 1, 2, C or D) or without (“k”= 0, 3 or B) sensor heating jacket / insulation. (“k”
is from the sensor VE code)
Ex d connection compartment
1 II 1/2 (1) G Ex db ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T160°C Db
Ex e connection compartment 2 II 1/2 (1) G Ex db eb ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T160°C Db
1Where "f" = 1 from the converter VE code
2Where "f" = 2 from the converter VE code
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 10 Thursday, February 4, 2021 12:19 PM

INTRODUCTION 1
11
OPTIMASS / 400
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.10 OPTIMASS 3000F / 3400C
The OPTIMASS 3000F is defined by the sensor VE code VEab…k…l…n…where “l”defines the
hazardous areas approval, “ab”= 01, 03 or 04 and “n”= 1 or 2
The OPTIMASS 3400C is defined by the sensor VE code VE0b…k…l…n…where “l”defines the
hazardous areas approval, “ab”= 01, 03 or 04 and “n”= 0
The marking for the the OPTIMASS 3000F / 3400C is shown in the following tables:
OPTIMASS 3000F with ("k" = 2) or without ("k" = 0 or 3) heating jacket / insulation)
Intrinsically safe II 1 G Ex ia IIC T6...T1 Ga
II 1 D Ex ia IIIC T165°C Da
OPTIMASS 3400C Non Ex i signal outputs (where the converter VE code VE5b…f…npq…and n ≠2 or 3, or
n = D or E when “p”≠0, 1 or 2) with (“k”= 2) or without (“k”= 0 or 3) sensor heating jacket / insulation (“k”is
from the sensor VE code.)
Ex d connection compartment
1 II 1/2 G Ex db ia IIC T6...T1 Ga / Gb
II 2 D Ex tb IIIC T165°C Db
Ex e connection compartment 2 II 1/2 G Ex db eb ia IIC T6...T1 Ga / Gb
II 2 D Ex tb IIIC T165°C Db
OPTIMASS 3400C Ex i signal outputs (where the converter VE code VE5b…f…npq…and “n”= 2, 3, D or E
and “p”= 0, 1 or 2) with (“k”= 2) or without (“k”= 0 or 3) sensor heating jacket / insulation. (“k”is from the
sensor VE code.)
Ex d connection compartment
1 II 1/2(1) G Ex db ia [ia Ga] IIC T6...T1 Ga / Gb
II 2(1) D Ex tb [ia Da] IIIC T165°C Db
Ex e connection compartment 2 II 1/2(1) G Ex db eb ia [ia Ga] IIC T6...T1 Ga / Gb
II 2(1) D Ex tb [ia Da] IIIC T165°C Db
1Where "f" = 1 from the converter VE code
2Where "f" = 2 from the converter VE code
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 11 Thursday, February 4, 2021 12:19 PM

1INTRODUCTION
12
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.11 OPTIMASS 6000F / 6400C
Standard temperature version ("j" = K and "q"
Standard temperature version ("j" = K and "q"Standard temperature version ("j" = K and "q"
Standard temperature version ("j" = K and "q" ≠T)
T)T)
T)
The OPTIMASS 6000F is defined by the sensor VE code ab…j...k…l…n…q... where “l”defines the
hazardous areas approval, “ab”= 71, 72, 73, 74, 75, 76, 77, 78, 79 or 80 and “n”= 1 or 2, "j" = K and
"q" ≠T
The OPTIMASS 6400C is defined by the sensor VE code ab…j...k…l…n…q... where “l”defines the
hazardous areas approval, “ab”= 71, 72, 73, 74, 75, 76, 77, 78, 79 or 80 and “n”= 0, "j" = K and "q"
≠T
The markings for the OPTIMASS 6000F / 6400C are shown in the following tables:
OPTIMASS 6000F with ("k" = 1, 3 or 5) or without ("k" = 0 or A) heating jacket / insulation)
Intrinsically safe II 1 G Ex ia IIC T6...T1 Ga
II 1 D Ex ia IIIC T270°C Da
OPTIMASS 6400C Non Ex i signal outputs (where the converter VE code VE5b…f…npq…and n ≠2 or 3, or
n = D or E when “p”≠0, 1 or 2) with (“k”= 1, 3 or 5) or without (“k”= 0 or A) sensor heating jacket / insulation
(“k”is from the sensor VE code)
Ex d connection compartment
1 II 1/2 G Ex db ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T270°C Db
Ex e connection compartment 2 II 1/2 G Ex db eb ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T270°C Db
OPTIMASS 6400C Ex i signal outputs (where the converter VE code VE5b…f…npq…and “n”= 2, 3, D or E
and “p”= 0, 1 or 2) with (“k”= 1, 3 or 5) or without (“k”= 0 or A) sensor heating jacket / insulation. (“k”is from
the sensor VE code)
Ex d connection compartment
1 II 1/2 (1) G Ex db ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T270°C Db
Ex e connection compartment 2 II 1/2 (1) G Ex db eb ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T270°C Db
1Where "f" = 1 from the converter VE code
2Where "f" = 2 from the converter VE code
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 12 Thursday, February 4, 2021 12:19 PM

INTRODUCTION 1
13
OPTIMASS / 400
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
Short stem version ("j" = 0)
Short stem version ("j" = 0)Short stem version ("j" = 0)
Short stem version ("j" = 0)
The OPTIMASS 6000F is defined by the sensor VE code VEab…j...k…l…n…q... where “l”defines
the hazardous areas approval, “ab”= 71, 72, 73, 74, 75, 76, 77, 78, 79 or 80 and “n”= 1 or 2, and "j"
= 0
The OPTIMASS 6400C is defined by the sensor VE code VEab…j...k…l…n…q... where “l”defines
the hazardous areas approval, “ab”= 71, 72, 73, 74, 75, 76, 77, 78, 79 or 80 and “n”= 0, and "j" = 0
The markings for the OPTIMASS 6000F / 6400C are shown in the following tables:
High temperature version ("q" = T)
High temperature version ("q" = T)High temperature version ("q" = T)
High temperature version ("q" = T)
The OPTIMASS 6000F is defined by the sensor VE code VEab…j...k…l…n…q... where “l”defines
the hazardous areas approval, “ab”= 71, 72, 73, 74, 75, 76, 77, 78, 79 or 80 and “n”= 1 or 2, and "q"
= T
OPTIMASS 6000F with ("k" = 1, 3 or 5) or without ("k" = 0 or A) heating jacket / insulation)
Intrinsically safe II 1 G Ex ia IIC T6...T1 Ga
II 1 D Ex ia IIIC T190°C Da
OPTIMASS 6400C Non Ex i signal outputs (where the converter VE codeVE5 b…f…npq…and n ≠2 or 3, or
n = D or E when “p”≠0, 1 or 2) with (“k”= 1, 3 or 5) or without (“k”= 0 or A) sensor heating jacket / insulation
(“k”is from the sensor VE code)
Ex d connection compartment
1 II 1/2 G Ex db ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T190°C Db
Ex e connection compartment 2 II 1/2 G Ex db eb ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T190°C Db
OPTIMASS 6400C Ex i signal outputs (where the converter VE code VE5b…f…npq…and “n”= 2, 3, D or E
and “p”= 0, 1 or 2) with (“k”= 1, 3 or 5) or without (“k”= 0 or A) sensor heating jacket / insulation. (“k”is from
the sensor VE code)
Ex d connection compartment
1 II 1/2 (1) G Ex db ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T190°C Db
Ex e connection compartment 2 II 1/2 (1) G Ex db eb ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T190°C Db
1Where "f" = 1 from the converter VE code
2Where "f" = 2 from the converter VE code
OPTIMASS 6000F with ("k" = 1, 3 or 5) sensor heating jacket / insulation
Intrinsically safe II 1 G Ex ia IIC T6...T1 Ga
II 1 D Ex ia IIIC T440°C Da
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 13 Thursday, February 4, 2021 12:19 PM

1INTRODUCTION
14
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.12 OPTIMASS 7000F / 7400C
The OPTIMASS 7000F is defined by the sensor VE code VEab…k…l…n…where “l”defines the
hazardous area approval, “a”= 1, 2, 3 or 4 and "b" = 1, 2, 3, 4, 5, 6 or 7 and "n" = 1 or 2
The OPTIMASS 7400C is defined by the sensor VE code VEab...k…l…n…q where “l”defines the
hazardous areas approval, "a”= 1, 2, 3 or 4 and "b" = 1, 2, 3, 4, 5, 6 or 7 and "n" = 0
The markings for the OPTIMASS 7000F / 7400C are shown in the following tables:
OPTIMASS 7000F with ("k" = 1 or 2) or without ("k" = 0 or 3) sensor heating jacket / insulation)
Intrinsically safe II 1 G Ex ia IIC T6...T1 Ga
II 1 D Ex ia IIIC T165°C Da
OPTIMASS 7400C Non Ex i signal outputs (where the r converter VE code VE5b…f…npq…and n ≠2 or 3, or
n = D or E when “p”≠0, 1 or 2) with (“k”= 1 or 2) or without (“k”= 0 or 3) sensor heating jacket / insulation
(“k”is from the sensor VE code)
Ex d connection compartment
1 II 1/2 G Ex db ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T165°C Db
Ex e connection compartment 2 II 1/2 G Ex db eb ia IIC T6...T1 Ga/Gb
II 2 D Ex tb IIIC T165°C Db
OPTIMASS 7400C Ex i signal outputs (where the converter VE code VE5b…f…npq…and “n”= 2, 3, D or E
and “p”= 0, 1 or 2) with (“k”= 1 or 2) or without (“k”= 0 or 3) sensor heating jacket / insulation. (“k”is from
the sensor VE code)
Ex d connection compartment
1 II 1/2 (1) G Ex db ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T165°C Db
Ex e connection compartment 2 II 1/2 (1) G Ex db eb ia [ia Ga] IIC T6...T1 Ga/Gb
II 2 (1) D Ex tb [ia Da] IIIC T165°C Db
1Where "f" = 1 from the converter VE code
2Where "f" = 2 from the converter VE code
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 14 Thursday, February 4, 2021 12:19 PM

INTRODUCTION 1
15
OPTIMASS / 400
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
1.13 Nameplates
The nameplate contains information about the sensor and converter. Below are examples of
both compact and field versions of the nameplate.
Converter nameplate (compact and remote versions)
1 Ex marking (example shown)
2 Certificate number
3 Ex specific requirement
4 Power supply data
5 VE Codes for sensor and converter / manual document number
6 Year of manufacture / serial number
7 Model type (OPTIMASS x400 C or OPTIMASS x400C - painted)
8 Logo and address of manufacturer
9 Identification number of the notified body (example shown)
Sensor nameplate (remote version only)
1 Ex marking (example shown)
2 Certificate number
3 Ex specific requirement
4 Identification number of the notified body (example shown)
5 Manual document number
6 VE Code for x000 sensor
7 Serial number
8 Model type (OPTIMASS x000F or OPTIMASS x000F -- painted)
9 Logo and address of manufacturer
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 15 Thursday, February 4, 2021 12:19 PM

2SPECIAL CONDITIONS
16
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
Special Conditions
2.1 Equipotential bonding
The MFC 400F (field) (remote) converter and the OPTIMASS X400C (compact) must be included
in the equipotential bonding of the installation. Use the bonding terminal on the converter
housing, wall bracket or mass flow meter housing mounting stem.
In separated systems, a screened cable is used and is earthed at the meter and converter ends.
Fit an equalisation cable with a minimum cross section area of 4mm
2
to the equipotential
bonding terminals on the mass flow converter housing bracket and the mass flow sensor
electronics stem.
2.2 Electrostatic charge
To reduce the ignition hazard caused by an electrostatic charge collecting on the instrument, you
must obey the following instructions:
•DO NOT clean the meter and / or converter with a dry cloth.
•DO NOT install the meter and / or converter near to any process that uses an electrostatic
charge, for example a dry powder coating system.
•DO NOT use the meter for applications where the process can generate a strong electrostatic
charge.
•DO NOT install the meter in an area where it will be in contact with airborne particles that can
cause an electrostatic charge.
2.3 Converter orientation (compact version)
DO NOT rotate the converter housing on the meter stem. Rotating the converter housing can
cause damage to the internal wiring.
CAUTION!
Electrostatic charging of the meter and / or converter housing MUST be avoided.
CAUTION!
Damage to the internal wiring could effect the Ex integrity of the meter.
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 16 Thursday, February 4, 2021 12:19 PM

SPECIAL CONDITIONS 2
17
OPTIMASS / 400
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
2.4 Temperature limits
2.4.1 Introduction
Because of the effect that the process temperature has on the meter, mass flow sensors and
compact mass flow meters are not given a fixed temperature class. The tables in this section
give details of the temperature class for each meter.
Notes
•Make sure that the flowmeter is installed and operated as shown in the relevant Handbook.
•Make sure that the flowmeter is not exposed to a source of heat (for example direct sunlight
or heat from adjacent equipment) that causes the ambient temperature to rise above the
ambient temperature range for the meter.
•Make sure that insulation is not preventing ventilation of the meter housing.
2.4.2 MFC 400F
The MFC 400F is defined by the converter VE code VEab…d…f...l…npq…where “f”defines the
hazardous area approval and “ab”= 53 or 54 and “d”= H
The MFC 400F mass flow converter is suitable for temperature classes T6…T1 and has a
maximum surface temperature of 75ºC
Note:
Note:Note:
Note:
These temperature classes are subject to the following temperature limits. For information on
cable parameters, please refer to the ELECTRICAL CONNECTIONS chapter.
Converter housing Ambient temp. T
amb
°C
Standard Converter SIL capable Converter
Aluminium (VE code option "I" = 1) -40...+65°C / -40...+149°F -40...+55°C / -40...+131°F
Stainless Steel (VE code option "I" = 3) -40...+60°C / -40...+140°F -40...+55°C / -40...+131°F
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 17 Thursday, February 4, 2021 12:19 PM

2SPECIAL CONDITIONS
18
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
2.4.3 OPTIMASS 1000F / 1400C
The OPTIMASS 1000F / 1400C is suitable for temperature classes T6...T1
Note:
Note:Note:
Note:
These temperature classes are subject to the following temperature limits. For information on
cable parameters, please refer to the ELECTRICAL CONNECTIONS chapter.
Ambient temp.
T
amb
°C
Max medium
temp. T
m
°C
Temp. class Max. Surface
temp. °C
OPTIMASS 1000F
is defined by the sensor VE code
VEab…k…l…n…where “l”defines the
hazardous areas approval, “ab”= 83, 84, 85, or 86
and “n”= 1 or 2 with (“k”= 1 or 2) or without (“k”=
0 or 3) heating jacket / insulation
-40...+40 45 T6 - T1 T80
60 T5 - T1 T95
95 T4 - T1 T130
130 T3 - T1 T165
150 T3 - T1 T185
-40...+50 60 T5 - T1 T95
95 T4 - T1 T130
130 T3 - T1 T165
150 T3 - T1 T185
-40...+65 95 T4 - T1 T130
130 T3 - T1 T165
150 T3 - T1 T185
Minimum medium temp: -50ºC
OPTIMASS 1400C –aluminium converter
housing
is defined by the sensor VE code
VEab…k…l…n…where “l”defines the
hazardous areas approval, “ab”= 83, 84, 85, or 86
and “n”= 0 –with (“k”= 1 or 2) or without (“k”= 0
or 3) heating jacket / insulation and the converter
VE code VE5b…d…f…l…npq –where “b”= 3 or 4
and “d”= 4 and “l”= 1
-40...+40 45 T6 - T1 T80
60 T5 - T1 T95
95 T4 - T1 T130
130 T3 - T1 T165
150 T3 - T1 T185
-40...+50 60 T5 - T1 T95
95 T4 - T1 T130
130 T3 - T1 T165
150 T3 - T1 T185
-40...+65 65 T4 - T1 T100
Minimum medium temp: -45ºC
OPTIMASS 1400C –SS converter housing
is defined by the sensor VE code
VEab…k…l…n…where “l”defines the
hazardous areas approval, “ab”= 83, 84, 85, or 86
and “n”= 0 –with (“k”= 1 or 2) or without (“k”= 0
or 3) heating jacket / insulation and the converter
VE code VE5b…d…f…l...npq - where “b”= 3 or 4
and “d”= 4 and “l”= 2
-40...+40 45 T6 - T1 T80
60 T5 - T1 T95
95 T4 - T1 T130
130 T3 - T1 T165
150 T3 - T1 T185
-40...+50 60 T5 - T1 T95
95 T4 - T1 T130
-40...+60 60 T5 - T1 T95
Minimum medium temp: -45ºC
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 18 Thursday, February 4, 2021 12:19 PM

SPECIAL CONDITIONS 2
19
OPTIMASS / 400
www.krohne.com02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
2.4.4 OPTIMASS 2000F / 2400C
The OPTIMASS 2000F / 2400C is suitable for temperature classes T6...T1
Note:
Note:Note:
Note:
These temperature classes are subject to the following temperature limits. For information on
cable parameters, please refer to the ELECTRICAL CONNECTIONS chapter.
Ambient temp.
T
amb
°C
Max medium
temp. T
m
°C
Temp. class Max. Surface
temp. °C
OPTIMASS 2000F - with or without heating jacket
/ insulation
is defined by the sensor VE code
VEab…k…l…n…, where “l”defines the
hazardous areas approval, “ab”= 87, 88, 89, or 90
and “n”= 1 or 2 with (“k”= 1, 2, C or D) or without
(“k”= 0, 3 or B) heating jacket / insulation
-40...+40 40 T6 - T1 T70
55 T5 - T1 T85
90 T4 - T1 T120
130 T3 - T1 T160
-40...+50 55 T5 - T1 T85
90 T4 - T1 T120
130 T3 - T1 T160
-40...+65 65 T5 - T1 T95
90 T4 - T1 T120
130 T3 - T1 T160
Minimum medium temp: -50ºC
OPTIMASS 2400C –aluminium converter
housing
is defined by the sensor VE code
VEab…k…l…n…, where “I”defines the
hazardous areas approval, “ab”= 87, 88, 89, or 90
and “n”= 0 –with (“k”= 1, 2, C or D) or without (“k”
= 0, 3 or B) sensor heating jacket / insulation and
the converter VE code code VE5b…d…f…l…npq
–where “b”= 3 or 4 and “d”= 4 and “l”= 1
-40...+40 40 T6 - T1 T70
55 T5 - T1 T85
90 T4 - T1 T120
130 T3 - T1 T160
-40...+50 55 T5 - T1 T85
90 T4 - T1 T120
130 T3 - T1 T160
-40...+60 65 T5 - T1 T95
100 T4 - T1 T130
-40...+65 1 65 T5 - T1 T95
Minimum medium temp: -45ºC
OPTIMASS 2400C –SS converter housing
is defined by the sensor VE code
VEab…k…l…n…, where “l”defines the
hazardous areas approval, “ab”= 87, 88, 89, or 90
and “n”= 0 –with (“k”= 1, 2, C or D) or without (“k”
= 0, 3 or B) heating jacket / insulation and the
converter VE code VE5b…d…f…l...npq…-
where “b”= 3 or 4 and “d”= 4 and “l”= 2
-40...+40 40 T6 - T1 T70
55 T5 - T1 T85
90 T4 - T1 T120
130 T3 - T1 T160
-40...+50 55 T5 - T1 T85
90 T4 - T1 T120
-40...+60 60 T5 - T1 T90
Minimum medium temp: -45ºC
1Depending on I/O option. Please call for more information.
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 19 Thursday, February 4, 2021 12:19 PM

2SPECIAL CONDITIONS
20
OPTIMASS / 400
www.krohne.com 02/2021 - 4003491805- AD OPTIMASS 400 Atex R05 en
2.4.5 OPTIMASS 3000F / 3400C
The OPTIMASS 3000F / 3400C is suitable for temperature classes T6...T1
Note:
Note:Note:
Note:
These temperature classes are subject to the following temperature limits. For information on
cable parameters, please refer to the ELECTRICAL CONNECTIONS chapter.
Ambient temp.
T
amb
°C
Max medium
temp. T
m
°C
Temp. class Max. Surface
temp. °C
OPTIMASS 3000F
is defined by the sensor VE code
VEab…k…l…n…, where “l”defines the
hazardous areas approval, “ab”= 01, 03 or 04 and
"n" = 1 or 2 - with ("k" = 2) or without ("k" = 0 or 3)
heating jacket / insulation
-40...+40 65 T6 - T1 T80
80 T5 - T1 T95
115 T4 - T1 T130
150 T3 - T1 T165
-40...+50 65 T6 - T1 T80
80 T5 - T1 T95
115 T4 - T1 T130
150 T3 - T1 T165
-40...+65 65 T6 - T1 T80
80 T5 - T1 T95
115 T4 - T1 T130
130 T3 - T1 T145
Minimum medium temp: -50ºC
OPTIMASS 3400C –aluminium converter
housing
is defined by the sensor VE code
VEab…l…k...n…, where “I”defines the
hazardous areas approval, “ab”= 01,03 or 04 and
“n”= 0 –with (“k”= 2) or without (“k”= 0 or 3)
sensor heating jacket / insulation and the
converter VE code VE5b…d…f…l…npq –where
“b”= 3 or 4 and “d”= 4 and “l”= 1
-40...+40 65 T6 - T1 T80
80 T5 - T1 T95
115 T4 - T1 T130
150 T3 - T1 T165
-40...+50 65 T6 - T1 T80
80 T5 - T1 T95
115 T4 - T1 T130
150 T3 - T1 T165
-40...+65 65 T6 - T1 T80
Minimum medium temp: -45ºC
OPTIMASS 3400C –SS converter housing
is defined by the sensor VE code
VEab…l…k…n…, where “l”defines the
hazardous areas approval, “ab”= 01, 03 or 04 and
“n”= 0 –with (“k”= 2) or without (“k”= 0 or 3)
heating jacket / insulation and the Converter VE
Code VE5b…d…f…l...npq…- where and “b”= 3
or 4 and “d”= 4 and “l”= 2
-40...+40 65 T6 - T1 T80
80 T5 - T1 T95
115 T4 - T1 T130
150 T3 - T1 T165
-40...+50 65 T6 - T1 T80
80 T5 - T1 T95
115 T4 - T1 T130
130 T3 - T1 T145
-40...+60 60 T6 - T1 T75
Minimum medium temp: -45ºC
AD_OPTIMAS_400_Haz_Areas_en_210201_4003491805_R05.book Page 20 Thursday, February 4, 2021 12:19 PM