KROHNE UFC 400 Wiring diagram

Signal converter for ultrasonic flowmeters
Description of Foundation Fieldbus interface
Description of Foundation Fieldbus interfaceDescription of Foundation Fieldbus interface
Description of Foundation Fieldbus interface
Electronic Revision: ER 3.0.1_
UFC 400
UFC 400UFC 400
UFC 400 Supplementary Instructions
Supplementary InstructionsSupplementary Instructions
Supplementary Instructions
© KROHNE 12/2015 - 4002813702 - AD FF UFC 400 R02 en
The documentation is only complete when used in combination with the relevant
documentation for the flow sensor.

CONTENTS
2
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
UFC 400
1 Safety instructions 3
1.1 Scope of the document..................................................................................................... 3
1.2 Device description ............................................................................................................ 3
2 Technical data 4
2.1 Foundation Fieldbus data................................................................................................. 4
3 Electrical connections 5
3.1 Cable types ....................................................................................................................... 5
3.2 Shielding and grounding .................................................................................................. 5
3.3 Electrical connection of FOUNDATION Fieldbus ............................................................. 6
3.4 Topology of FF networks .................................................................................................. 7
4 Operation 8
4.1 Settable functions............................................................................................................. 8
4.2 Description of the FF block system.................................................................................. 9
4.3 Used abbreviations ........................................................................................................... 9
4.4 Resource Block (RB) ...................................................................................................... 10
4.5 Analog Input Block (AI 1...4) ........................................................................................... 31
4.6 FLOWTB (Flow Transducer Block) ................................................................................. 39
4.7 DIAGTB (Diagnose Transducer Block) ........................................................................... 48
4.8 Integrator Block (IT) ....................................................................................................... 55
4.9 Proportional Integral Derivative Block (PID) ................................................................. 62

SAFETY INSTRUCTIONS 1
3
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
1.1 Scope of the document
These instructions are supplementary to the standard product documentation of the signal
converter. The details depicted therein, in particular the safety information are valid and should
be adhered to. The present supplementary instructions provide additional information for the
devices when being operated and connected to a Foundation Fieldbus.
1.2 Device description
This ultrasonic flowmeter is designed for the continuous measurement of actual volume flow,
mass flow, flow speed, velocity of sound, gain, SNR and diagnosis value.
Exclusively for bi-directional measuring of conductive and / or non-conductive fluids in closed,
completely filled pipeline circuits.
Your measuring device is supplied ready for operation. The factory settings for the operating
data have been made in accordance with your order specifications.
The following versions are available:
•Remote version (electrical connection to the measuring sensor via signal cable)
INFORMATION!
The present supplementary instruction for the signal converter with Foundation Fieldbus
interface, plus the software with the DD and CCF files are included in our scope of supply, in
addition to those items delivered for the standard device.

2 TECHNICAL DATA
4
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
2.1 Foundation Fieldbus data
Description
Type Ultrasonic flowmeter
Physical layer Foundation Fieldbus protocol that agrees with IEC 61158-2 and FISCO model;
galvanically isolated
Communication standard H1
ITK version 6.1
NAMUR 107 Supported within FF field diagnosis (FF-912)
Data blocks
Function blocks 1 x Enhanced Resource Block (RB)
1 x Customer Flow Transducer Block (FLOWTB)
1 x Customer Diagnose Transducer Block (DIAGTB)
4 x Analog Input Block (AI)
2 x Integrator Block (IT)
1 x Proportional Integral Derivate Block (PID)
Execution time Analog Input Block: 10 ms
Integrator Block: 15 ms
Proportional Integral Derivate Block: 25 ms
Electrical connections
Device power supply Not intrinsically safe: 9...32 VDC
Intrinsically safe: 9...24 VDC
Basic current 10.5 mA
Maximum error current 16.5 mA (= basic current + error current = 10.5 mA + 6 mA)
Start current after 10 ms 14 mA
Polarity sensitivity No
Minimum cycle time 250 ms

ELECTRICAL CONNECTIONS 3
5
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
3.1 Cable types
The cable types are specified according to IEC 61158-2. Shielded cables offer the advantage of
malfunction-free operation with adequate protection against electromagnetic influences, and
make it possible to employ the full performance of the Foundation Fieldbus system.
In non-hazardous locations, a maximum of 32 field devices can be connected to the network. For
more data, refer to the table that follows.
All bus segments must be fitted with a terminator at both ends.
3.2 Shielding and grounding
•For optimum electromagnetic compatibility of systems it is extremely important that the
system components, and particularly the bus cables connecting the components, are
shielded and that such shields - if possible - form an unbroken cover.
•Hence, it follows that, for use in non-hazardous duty systems, the cable shield should be
grounded as often as possible.
•In Ex systems an adequate equipotential bonding in the hazardous and non-hazardous
location along the entire Fieldbus installation is strongly recommended. Multiple grounding
of the shield is of advantage.
•In explosion-proof systems the shielding must at least be connected at one end of the cable.
•NAMUR NE 21 compliance is given, provided the above recommended cable types are used.
Core cross-section 0.8 mm
2
or
AWG 18 0.32 mm
2
or
AWG 22 0.13 mm
2
or
AWG 26 1.25 mm
2
or
AWG 16
Cable type A
AA
A B
BB
B C
CC
C D
DD
D
twisted pair,
individually
shielded
individual or
multiple twisted
pairs with overall
shield
multiple twisted
pairs, without
shielding
multiple non-
twisted cables,
without shielding
Max. length
incl. branch line 1900 m / 6200 ft 1200 m / 3900 ft 400 m / 1300 ft 200 m / 650 ft
Number of devices Cable lengths for number of devices per branch line
1 device 2 devices 3 devices 4 devices
25...32 1m/3.3ft 1m/3.3ft 1m/3.3ft 1m/3.3ft
19...24 30 m / 100 ft 1m/3.3ft 1m/3.3ft 1m/3.3ft
15...18 60 m / 200 ft 30 m / 100 ft 1m/3.3ft 1m/3.3ft
13...14 90 m / 300 ft 60 m / 200 ft 30 m / 100 ft 1m/3.3ft
1..12 120 m / 400 ft 90 m / 300 ft 60 m / 200 ft 30 m / 100 ft
INFORMATION!
The use of twisted and shielded cables is strongly recommended, otherwise EMC protection of
the signal converter cannot be assured.

3 ELECTRICAL CONNECTIONS
6
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
3.3 Electrical connection of FOUNDATION Fieldbus
Connection to a spur
Connection to a trunk
INFORMATION!
The wiring between the device and the FOUNDATION Fieldbus cable is independant of polarity.
The signal converter FOUNDATION Fieldbus interface will operate only if the additional power
supply for the device is connected/available.
For a detailed description of the electrical connections please refer to the standard signal
converter handbook.
or
or
1e.g. incoming data lines
2e.g. outgoing data lines

ELECTRICAL CONNECTIONS 3
7
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
3.4 Topology of FF networks
An example of mixed topology of FF networks is shown in the following example.
Connection is best made via short branch cables and T connectors. This connection type makes it
possible to connect and disconnect the devices without interrupting the bus or the
communication.
1HSE network
2H1 bus
3Intrisically safe, explosive area
B1+B2 Bridge = coupling element for H1 bus
and HSE network
D1-D3 Device = field devices, own power
supply, for non potentially explosive
areas
D4-D6 Intrinsically safe devices, external
power supply, for potentially explosive
areas
I.S. Intrinsically safe barrier
JB Junction box for field devices
PS Power supply
Switch = connection of multiple HSE
sub networks
T Terminator

4 OPERATION
8
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
4.1 Settable functions
•For Foundation Fieldbus the totalizers of the signal converter are not available!
•The following tables describe only the menus, functions and parameters that are different
between the standard signal converter and the Foundation Fieldbus signal converter.
•For the electrical connections of the outputs, inputs and all settings of functions that are not
listed in the following tables refer to the standard product documentation.
No. Displayed text Description and settings
A quick setup
A2 Tag Identifier for the measurement in a plant, appears in the display header
(maximum 8 digits).
Note: Only read, not changeable!
B test
B3.7 Foundation fieldbus Display information about Foundation fieldbus interface.
C setup
C5.1.1 Tag Identifier for the measurement in a plant, appears in the display header
(maximum 8 digits).
Note: Only read, not changeable!
C3 Totalizer Not available for Foundation Fieldbus devices!
C4 I/O HART Not available for Foundation Fieldbus devices!
C5.4 2. meas. page In case of Foundation Fieldbus device, the second measurement page is
meant to check the output values of the different function blocks. Only
Foundation Fieldbus values can be selected here. The analogue inputs are
shown with exactly the value, seen on the bus system.
C5.4.1 measurement 1.line Select: AI1...4 analog inp. / PID / INT1..2 integrator
C5.4.2 format 1.line Fixed number of digits after the decimal point or automatic, where the
number of digits is automatically adjusted to the available space.
C5.4.3 measurement 2.line Select: AI1...4 analog inp. / PID / INT1..2 integrator
C5.4.4 format 2.line Fixed number of digits after the decimal point or automatic, where the
number of digits is automatically adjusted to the available space.
C5.4.5 measurement 3.line Select: AI1...4 analog inp. / PID / INT1..2 integrator
C5.4.6 format 3.line Fixed number of digits after the decimal point or automatic, where the
number of digits is automatically adjusted to the available space.
C5.8 Foundation Field -
C5.8.1 Simulate Select: disabled / enabled
C5.8.2 Information Display information about hardware and software versions, the calibration
and test date of this interface.

OPERATION 4
9
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
4.2 Description of the FF block system
The Foundation Fieldbus is a Local Area Network (LAN) for connecting field devices like sensors
and actuators. One of the main benefits of Foundation Fieldbus is line saving in comparison to
the traditional 4...20 mA technology.
The different device functions are implemented in a block-based scheme within a user
application. In this block scheme, a distinction is made between the Resource Block, Transducer
Block and Function Block.
4.3 Used abbreviations
1 Resource Block (RB)
2 Transducer Block (TB)
3 Function Block (FB)
4 Device FF communication
5 Foundation Fieldbus
AI Analogue Input Block BLK Block mode
IT Integrator Block MAN Manual mode
PID Proportional Integral Derivate Block Mix Mix mode (R, W and R/W)
RB Resource Block Auto Automatic mode
TB Transducer Block OOS Out Of Service mode
RRead OD Object Directory
WWrite SP Set Point
R/W Read and Write IV Initial Value
PV Process Value (factory settings)

4 OPERATION
10
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
4.4 Resource Block (RB)
The following tables list the Resource Block parameters in alphabetical order.
It describes characteristics of the Fieldbus device (e.g. device name, serial number, etc.) and is
not included in the functional tasks of the signal converter for FF.
The following tables contain short parameter description, factory settings (Initial Value (IV)) and
possible settings.
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value
ALERT_KEY
ALERT_KEYALERT_KEY
ALERT_KEY
Alert Key
Alert KeyAlert Key
Alert Key R/W The identification number of the plant unit. This information may be used in the host for sorting alarms, etc. 0
Setting:
1...255
BLOCK_ERR
BLOCK_ERRBLOCK_ERR
BLOCK_ERR
Block Error
Block ErrorBlock Error
Block Error RThis parameter reflects the error status associated with the hardware or software components associated with a block. It
is a bit string, so that multiple errors may be shown.
OOS (Out of
Service)
Setting:
• Other: Non-specific error active
• Block Configuration: Error detected in block configuration
• Link Configuration: Error detected in link configuration
• Simulation Active: Simulation enabled in this block
• Local Override: Output tracking of faultstate active
• Device Fault State: Device faultstate set
• Device Maintenance: Device needs maintenance soon
• Input Failure: Process variable has bad status
• Output Failure: Failure detected in output hardware
• Memory Failure: Memory error detected
• Lost Static Data: Static parameters cannot be recovered
• Lost NV Data: Non-volatile parameters cannot be recovered
• Readback Check: Failure detected in READBACK
• Maintenance Needed: Device NEEDS maintenance NOW
• Power Up: Recovery from power failure
• Out Of Service: Block actual mode is out of service
MODE_BLK
MODE_BLKMODE_BLK
MODE_BLK
Block Mode
Block ModeBlock Mode
Block Mode Mix The actual, target, permitted and normal modes of the block. -
TARGET
Target R/W This is the mode requested by the operator. Only one mode from those allowed by the permitted mode parameter may be
requested.
OOS
Setting:
Auto / OOS
ACTUAL
Actual RThis is the current mode of the block, which may differ from the target based on operating conditions. Its value is
calculated as part of block execution.
OOS
Setting:
Auto / OOS
PERMITTED
Permitted R/W Defines the modes which are allowed for an instance of the block. The permitted mode is configured based on application
requirement.
Auto
OOS
Setting:
Auto / OOS

OPERATION 4
11
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
NORMAL
Normal R/W This is the mode which the block should be set to during normal operating conditions. Auto
Setting:
Auto / OOS
ST_REV
ST_REVST_REV
ST_REV
Static Revision
Static RevisionStatic Revision
Static Revision RThe revision level of the static data associated with the function block. The revision value will be incremented each
time a static parameter value in the block is changed.
0
Setting:
0...65535
STRATEGY
STRATEGYSTRATEGY
STRATEGY
Strategy
StrategyStrategy
Strategy R/W The strategy field can be used to identify grouping of blocks. This data is not checked or processed by the block. 0
Setting:
0...65535
TAG_DESC
TAG_DESCTAG_DESC
TAG_DESC
Tag Description
Tag DescriptionTag Description
Tag Description R/W The user description of the intended application of the block. blanks
Setting:
≤32 digits
ACK_OPTION
ACK_OPTIONACK_OPTION
ACK_OPTION
Acknowledge Option
Acknowledge OptionAcknowledge Option
Acknowledge Option R/W Selection of whether alarms associated with the function block will be automatically acknowledged. Uninitialized
Setting:
Disc Alm Auto Ack / Blk Alm Auto Ack / Fail Alm Auto Ack / Off
Spec Alm Auto Ack / Maint Alm Auto Ack / Check Alm Auto Ack
ALARM_SUM
ALARM_SUMALARM_SUM
ALARM_SUM
Alarm Summary
Alarm SummaryAlarm Summary
Alarm Summary RThe current alert status, unacknowledged states, unreported states and disabled states of the alarms associated with the
function block.
-
Current RThe active status of each alarm. Uninitialized
Setting:
Discrete Alarm / Block Alarm / Fail Alarm / Off Spec Alarm /
Maintenance Alarm / Check Alarm
Unacknowledged RThe unacknowledged state of each alarm. Uninitialized
Setting:
Disc Alm Unack / Block Alm Unack / Fail Alm Unack / Off Spec
Alm Unack / Maint Alm Unack / Check Alm Unack
Unreported RThe unreported status of each alarm. Uninitialized
Setting:
Disc Alm Unrep / Block Alm Unrep / Fail Alm Unrep / Off Spec
Alm Unrep / Maint Alm Unrep / Check Alm Unrep
Disabled R/W The disabled state of each alarm. Uninitialized
Setting:
Disc Alm Disabled / Block Alm Disabled / Fail Alm Disabled /
Off Spec Alm Disabled / Maint Alm Disabled / Check Alm
Disabled
BLOCK_ALM
BLOCK_ALMBLOCK_ALM
BLOCK_ALM
Block Alarm
Block AlarmBlock Alarm
Block Alarm The block alarm is used for all configuration, hardware, connection failure or system problems in the block. The cause
of the alert is entered in the subcode field. The first alert to
become active will set the "Active" status in the "Status"
attribute. As soon as the "Unreported" status is cleared by the
alert reporting task, another block alert may be reported
without clearing the "Active" status, if the subcode has
changed.
-
Unacknowledged R/W A discrete enumeration which is set to "Unacknowledged"
when an alarm occurs, and set to "Acknowledged" by a write
from a human interface device or other entity which can
acknowledge that the alarm/event has been noticed.
Uninitialized
Setting:
Uninitialized / Acknowledged / Unacknowledged
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

4 OPERATION
12
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
Alarm State RA discrete enumeration which gives an indication of whether
the alert is active and whether it has been reported. Uninitialized
Setting:
Uninitialized / Clear - reported / Clear - not reported / Active -
reported / Active - not reported
Time Stamp RThe time when evaluation of the block was started and a
change in alarm/event state was detected that is unreported.
The time stamp value will be maintained constant until alert
confirmation has been received - even if another change of
state occurs.
Uninitialized
Setting:
MM / DD / YY (Month / Day / Year)
HH:MM:SS (Hour:Minute:Second)
Subcode RAn enumeration specifying the cause of the alert to be
reported. Other
Setting:
Other / Block Configuration / Link Configuration / Simulation
Active / Local Override / Device Fault State / Device
Maintenance / Input Failure / Output Failure / Memory
Failure / Lost Static Data / Lost NV Data / Readback Check /
Maintenance Needed / Power Up / Out Of Service
Value RThe value of the associated parameter at the time the alert
was detected. 0
Setting:
0...255
CLR_FSTATE
CLR_FSTATECLR_FSTATE
CLR_FSTATE
Clear Fault State
Clear Fault StateClear Fault State
Clear Fault State R/W Writing a "Clear" to this parameter will clear the device fault state if the field condition, if any, has cleared. Off
Setting:
Uninitialized / Off / Clear
CONFIRM_TIME
CONFIRM_TIMECONFIRM_TIME
CONFIRM_TIME
Confirm Time
Confirm TimeConfirm Time
Confirm Time R/W The minimum time between retries of alert reports. 640000
Setting:
0...4294967295 in [1/32 ms]
CYCLE_SEL
CYCLE_SELCYCLE_SEL
CYCLE_SEL
Cycle Selection
Cycle SelectionCycle Selection
Cycle Selection R/W Used to select the block execution method for this resource. Uninitialized
Setting:
Scheduled / Block execution
CYCLE_TYPE
CYCLE_TYPECYCLE_TYPE
CYCLE_TYPE
Cycle Type
Cycle TypeCycle Type
Cycle Type RIdentifies the block execution methods available for this resource. Scheduled Block execution
Setting:
Scheduled / Block execution
DD_RESOURCE
DD_RESOURCEDD_RESOURCE
DD_RESOURCE
DD Resource
DD ResourceDD Resource
DD Resource RString identifying the tag of the resource which contains the Device Description for this resource. blanks
Setting:
≤32 digits
DD_REV
DD_REVDD_REV
DD_REV
DD Revision
DD RevisionDD Revision
DD Revision RRevision of the DD associated with the resource - used by an interface device to locate the DD file for the resource. Dependent on device version.
Setting:
Dependent on device version.
DEV_REV
DEV_REVDEV_REV
DEV_REV
Device Revision
Device RevisionDevice Revision
Device Revision RManufacturer revision number associated with the resource - used by an interface device to locate the DD file for the
resource.
Dependent on
device version.
Setting:
Dependent on device version.
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

OPERATION 4
13
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
DEV_TYPE
DEV_TYPEDEV_TYPE
DEV_TYPE
Device Type
Device TypeDevice Type
Device Type RManufacturer's model number associated with the resource - used by interface devices to locate the DD file for the
resource.
UFC400
Setting:
UFC400
FAULT_STATE
FAULT_STATEFAULT_STATE
FAULT_STATE
Fault State
Fault StateFault State
Fault State RCondition set by loss of communication to an output block, failure promoted to an output block or a physical contact.
When fault state condition is set, then output function blocks
will perform their "FSTATE" actions.
Clear
Setting:
Uninitialized / Off / Clear
FD_CHECK_ACTIVE
FD_CHECK_ACTIVEFD_CHECK_ACTIVE
FD_CHECK_ACTIVE
Check Active RThis parameter reflects the error conditions that are being detected as active as selected for this category. It is a bit
string, so that multiple conditions may be shown. See section
2.9.
-
Setting:
(00) Check / (01) Electronics : Operation Info /
(08) Electronics : Power Fail / (10) Configuration : Totaliser /
(11) Process : Signal Unreliable / (12) Process : Signal Lost /
(13) Process : Empty Pipe / (14) Electronics : IO Connection /
(15) Process : Current input / (16) M Process /
(17) M Configuration / (18) M Electronics / (19) M Sensor /
(20) S Process / (21) S Configuration / (22) S Electronics /
(23) S Sensor / (24) C Process / (25) C Configuration /
(26) C Electronics / (27) C Sensor / (28) F Process / (29) F
Configuration / (30) F Electronics / (31) F Sensor
FD_CHECK_ALM
FD_CHECK_ALMFD_CHECK_ALM
FD_CHECK_ALM
Check Alarm This parameter is used primarily to broadcast a change in the associated active conditions, which are not masked, for this
alarm category to a Host System.
-
Unacknowledged R/W A discrete enumeration which is set to "Unacknowledged"
when an alarm occurs, and set to "Acknowledged" by a write
from a human interface device or other entity which can
acknowledge that the alarm/event has been noticed.
Uninitialized
Setting:
Uninitialized / Acknowledged / Unacknowledged
Alarm State RA discrete enumeration which gives an indication of whether
the alert is active and whether it has been reported. Uninitialized
Setting:
Uninitialized / Clear - reported / Clear - not reported /
Active - reported / Active - not reported
Time Stamp RThe time when evaluation of the block was started and a
change in alarm/event state was detected that is unreported.
The time stamp value will be maintained constant until alert
confirmation has been received - even if another change of
state occurs.
Uninitialized
Setting:
MM / DD / YY (Month / Day / Year)
HH:MM:SS (Hour:Minute:Second)
Subcode RAn enumeration specifying the cause of the alert to be
reported. -
Value RThe value of the associated parameter at the time the alert
was detected. -
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

4 OPERATION
14
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
FD_CHECK_MAP
FD_CHECK_MAPFD_CHECK_MAP
FD_CHECK_MAP
Check Map R/W This parameter enables or disables conditions to be detected as active for this alarm category. (24) (25) (26) (27)
Setting:
(00) Check / (01) Electronics : Operation Info /
(08) Electronics : Power Fail / (10) Configuration : Totaliser /
(11) Process : Signal Unreliable / (12) Process : Signal Lost /
(13) Process : Empty Pipe / (14) Electronics : IO Connection /
(15) Process : Current input / (16) M Process /
(17) M Configuration / (18) M Electronics / (19) M Sensor /
(20) S Process / (21) S Configuration / (22) S Electronics /
(23) S Sensor / (24) C Process / (25) C Configuration /
(26) C Electronics / (27) C Sensor / (28) F Process /
(29) F Configuration / (30) F Electronics / (31) F Sensor
FD_CHECK_MASK
FD_CHECK_MASKFD_CHECK_MASK
FD_CHECK_MASK
Check Mask R/W This parameter allows the user to suppress any single or multiple conditions that are active, in this category, from
being broadcast to the host through the alarm parameter.
Setting:
(00) Check / (01) Electronics : Operation Info /
(08) Electronics : Power Fail / (10) Configuration : Totaliser /
(11) Process : Signal Unreliable / (12) Process : Signal Lost /
(13) Process : Empty Pipe / (14) Electronics : IO Connection /
(15) Process : Current input / (16) M Process /
(17) M Configuration / (18) M Electronics / (19) M Sensor /
(20) S Process / (21) S Configuration / (22) S Electronics /
(23) S Sensor / (24) C Process / (25) C Configuration /
(26) C Electronics / (27) C Sensor / (28) F Process /
(29) F Configuration / (30) F Electronics / (31) F Sensor
FD_CHECK_PRI
FD_CHECK_PRIFD_CHECK_PRI
FD_CHECK_PRI
Check Priority R/W This parameter allows the user to specify the priority of this alarm category. 0
Setting:
0...15
FD_FAIL_ACTIVE
FD_FAIL_ACTIVEFD_FAIL_ACTIVE
FD_FAIL_ACTIVE
Fail Active RThis parameter reflects the error conditions that are being detected as active as selected for this category. It is a bit
string, so that multiple conditions may be shown. See section
2.9.
Uninitialized
Setting:
(00) Check / (01) Electronics : Operation Info /
(08) Electronics : Power Fail / (10) Configuration : Totaliser /
(11) Process : Signal Unreliable / (12) Process : Signal Lost /
(13) Process : Empty Pipe / (14) Electronics : IO Connection /
(15) Process : Current input / (16) M Process /
(17) M Configuration / (18) M Electronics / (19) M Sensor /
(20) S Process / (21) S Configuration / (22) S Electronics /
(23) S Sensor / (24) C Process / (25) C Configuration /
(26) C Electronics / (27) C Sensor / (28) F Process /
(29) F Configuration / (30) F Electronics / (31) F Sensor
FD_FAIL_ALM
FD_FAIL_ALMFD_FAIL_ALM
FD_FAIL_ALM
Fail Diagnostic Alarm This parameter is used primarily to broadcast a change in the associated active conditions, which are not masked, for this
alarm category to a Host System.
-
Unacknowledged R/W A discrete enumeration which is set to "Unacknowledged"
when an alarm occurs, and set to "Acknowledged" by a write
from a human interface device or other entity which can
acknowledge that the alarm/event has been noticed.
Uninitialized
Setting:
Uninitialized / Acknowledged / Unacknowledged
Alarm State RA discrete enumeration which gives an indication of whether
the alert is active and whether it has been reported. Uninitialized
Setting:
Uninitialized / Clear - reported / Clear - not reported / Active -
reported / Active - not reported
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

OPERATION 4
15
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
Time Stamp RThe time when evaluation of the block was started and a
change in alarm/event state was detected that is unreported.
The time stamp value will be maintained constant until alert
confirmation has been received - even if another change of
state occurs.
Uninitialized
Setting:
MM / DD / YY (Month / Day / Year)
HH:MM:SS (Hour:Minute:Second)
Subcode RAn enumeration specifying the cause of the alert to be
reported. -
Value RThe value of the associated parameter at the time the alert
was detected. -
FD_FAIL_MAP
FD_FAIL_MAPFD_FAIL_MAP
FD_FAIL_MAP
Fail Map R/W This parameter enables or disables conditions to be detected as active for this alarm category. (28) (29) (30) (31)
Setting:
(00) Check / (01) Electronics : Operation Info /
(08) Electronics : Power Fail / (10) Configuration : Totaliser /
(11) Process : Signal Unreliable / (12) Process : Signal Lost /
(13) Process : Empty Pipe / (14) Electronics : IO Connection /
(15) Process : Current input / (16) M Process /
(17) M Configuration / (18) M Electronics / (19) M Sensor /
(20) S Process / (21) S Configuration / (22) S Electronics /
(23) S Sensor / (24) C Process / (25) C Configuration /
(26) C Electronics / (27) C Sensor / (28) F Process /
(29) F Configuration / (30) F Electronics / (31) F Sensor
FD_FAIL_MASK
FD_FAIL_MASKFD_FAIL_MASK
FD_FAIL_MASK
Fail Mask R/W This parameter allows the user to suppress any single or multiple conditions that are active, in this category, from
being broadcast to the host through the alarm parameter.
(28) (29) (30) (31)
Setting:
(00) Check / (01) Electronics : Operation Info / (08) Electronics
: Power Fail / (10) Configuration : Totaliser / (11) Process :
Signal Unreliable / (12) Process : Signal Lost / (13) Process :
Empty Pipe / (14) Electronics : IO Connection / (15) Process :
Current input / (16) M Process / (17) M Configuration /
(18) M Electronics / (19) M Sensor / (20) S Process /
(21) S Configuration / (22) S Electronics / (23) S Sensor /
(24) C Process / (25) C Configuration / (26) C Electronics /
(27) C Sensor / (28) F Process / (29) F Configuration /
(30) F Electronics / (31) F Sensor
FD_FAILK_PRI
FD_FAILK_PRIFD_FAILK_PRI
FD_FAILK_PRI
Fail Priority R/W This parameter allows the user to specify the priority of this alarm category. 0
Setting:
0...15
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_1
ACTIVE_1ACTIVE_1
ACTIVE_1
FD_EXTENDED_
ACTIVE_1
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Optical Interf. Active / (01) Disp. 2 Overrange / (02) Disp. 1
Overrange / (06) RB is set to OOS / (07) Fieldbus No
Connection / (11) Status Out B Active / (13) Status Out A
Active / (14) Control In B Active / (15) Control In A Active / (30)
Sensor Starting up / (31) Zero Calibr. Running
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_2
ACTIVE_2ACTIVE_2
ACTIVE_2
FD_EXTENDED_
ACTIVE_2
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(20) Disp. 2 no measure values / (21) Dsp. 1 no measure
values / (28) IO B No Value for Binary Output / (29) IO B No
Value for Current Output / (30) IO A No Value for Binary
Output / (31) IO A No Value for Current Output
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

4 OPERATION
16
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_3
ACTIVE_3ACTIVE_3
ACTIVE_3
FD_EXTENDED_
ACTIVE_3
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_4
ACTIVE_4ACTIVE_4
ACTIVE_4
FD_EXTENDED_
ACTIVE_4
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_5
ACTIVE_5ACTIVE_5
ACTIVE_5
FD_EXTENDED_
ACTIVE_5
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_6
ACTIVE_6ACTIVE_6
ACTIVE_6
FD_EXTENDED_
ACTIVE_6
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_7
ACTIVE_7ACTIVE_7
ACTIVE_7
FD_EXTENDED_
ACTIVE_7
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_8
ACTIVE_8ACTIVE_8
ACTIVE_8
FD_EXTENDED_
ACTIVE_8
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_9
ACTIVE_9ACTIVE_9
ACTIVE_9
FD_EXTENDED_
ACTIVE_9
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_10
ACTIVE_10ACTIVE_10
ACTIVE_10
FD_EXTENDED_
ACTIVE_10
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_11
ACTIVE_11ACTIVE_11
ACTIVE_11
FD_EXTENDED_
ACTIVE_11
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(28) Time of Flight / (29) Path 3 unreliable /
(30) Path 2 unreliable / (31) Path 1 unreliable
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_12
ACTIVE_12ACTIVE_12
ACTIVE_12
FD_EXTENDED_
ACTIVE_12
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(29) Signal lost path 3 / (30) Signal lost path 2 /
(31) Signal lost path 1
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

OPERATION 4
17
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_13
ACTIVE_13ACTIVE_13
ACTIVE_13
FD_EXTENDED_
ACTIVE_13
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(31) Empty Pipe
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_14
ACTIVE_14ACTIVE_14
ACTIVE_14
FD_EXTENDED_
ACTIVE_14
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(28) IO B Connect. Control Input / (29) IO B Connect. Current
In-/Output / (30) IO A Connect. Control Input / (31) IO A
Connect. Current In-/Output
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_15
ACTIVE_15ACTIVE_15
ACTIVE_15
FD_EXTENDED_
ACTIVE_15
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(30) IO B Error Current / (31) IO A Error Current
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_16
ACTIVE_16ACTIVE_16
ACTIVE_16
FD_EXTENDED_
ACTIVE_16
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_17
ACTIVE_17ACTIVE_17
ACTIVE_17
FD_EXTENDED_
ACTIVE_17
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(30) Backup 2 Data Faulty / (31) Backup 1 Data Faulty
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_18
ACTIVE_18ACTIVE_18
ACTIVE_18
FD_EXTENDED_
ACTIVE_18
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(29) Backplane Difference / (30) Factory Data Faulty / (31)
Backplane Data Faulty
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_19
ACTIVE_19ACTIVE_19
ACTIVE_19
FD_EXTENDED_
ACTIVE_19
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_20
ACTIVE_20ACTIVE_20
ACTIVE_20
FD_EXTENDED_
ACTIVE_20
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(31) Velocity Out of Range
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_21
ACTIVE_21ACTIVE_21
ACTIVE_21
FD_EXTENDED_
ACTIVE_21
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(03) IO B Overrange Binary Output / (04) IO B Overrange
Current Output / (05) IO B Overrange Current In-/Output / (06)
IO A Overrange Binary Output / (07) IO A Overrange Current
Output / (09) IO A Overrange Current In-/Output
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_22
ACTIVE_22ACTIVE_22
ACTIVE_22
FD_EXTENDED_
ACTIVE_22
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(29) Conv. Zero too large
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

4 OPERATION
18
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_23
ACTIVE_23ACTIVE_23
ACTIVE_23
FD_EXTENDED_
ACTIVE_23
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_24
ACTIVE_24ACTIVE_24
ACTIVE_24
FD_EXTENDED_
ACTIVE_24
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_25
ACTIVE_25ACTIVE_25
ACTIVE_25
FD_EXTENDED_
ACTIVE_25
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(06) IO B Simulation Active / (07) IO B Sim. Binary Output / (08)
IO B Sim. Current In-/Output / (09) IO B Sim. Limit Sw./Current
Out / (10) IO A Sim. Binary Output /
(11) IO A Sim. Current In-/Output / (12) IO A Sim. Limit
Sw./Current Out / (30) VoS Simulation Active /
(31) Flow Simulation Active
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_26
ACTIVE_26ACTIVE_26
ACTIVE_26
FD_EXTENDED_
ACTIVE_26
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_27
ACTIVE_27ACTIVE_27
ACTIVE_27
FD_EXTENDED_
ACTIVE_27
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_28
ACTIVE_28ACTIVE_28
ACTIVE_28
FD_EXTENDED_
ACTIVE_28
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_29
ACTIVE_29ACTIVE_29
ACTIVE_29
FD_EXTENDED_
ACTIVE_29
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(02) IO B Binary Output Config / (03) IO B Current In-/Output
Config / (04) IO A Binary Output Config / (05) IO A Current In-
/Output Config. / (10) IO2 Configuration /
(11) IO1 Configuration / (12) Display Config. / (26) Process
Input Config. / (30) DM Configuration / (31) BM Configuration
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_30
ACTIVE_30ACTIVE_30
ACTIVE_30
FD_EXTENDED_
ACTIVE_30
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(01) IO B Failure / (02) IO A Failure / (07) IO 2 Failure / (08) IO 1
Failure / (18) Sensor Driver Failure / (19) DSP Failure / (20)
uProc. Failure / (21) FrontEnd Failure / (26) DM Failure / (27)
BM Failure / (28) HW Combination Error / (31) System Error
FD_EXTENDED_
FD_EXTENDED_FD_EXTENDED_
FD_EXTENDED_
ACTIVE_31
ACTIVE_31ACTIVE_31
ACTIVE_31
FD_EXTENDED_
ACTIVE_31
RAn optional parameter to allow the user finer detail on
conditions causing an active condition in the FD_*_ACTIVE
parameter.
Uninitialized
Setting:
(31) Crossed Cabling
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

OPERATION 4
19
UFC 400
www.krohne.com12/2015 - 4002813702 - AD FF UFC 400 R02 en
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
1
11
1
FD_EXTENDED_MAP_
1
R/W Field Diagnostics of "Electronics : Operation Info" Uninitialized
Setting:
(00) Optical Interf. Active / (01) Disp. 2 Overrange / (02) Disp. 1
Overrange / (06) RB is set to OOS / (07) Fieldbus No
Connection / (11) Status Out B Active / (13) Status Out A
Active / (14) Control In B Active / (15) Control In A Active / (30)
Sensor Starting up / (31) Zero Calibr. Running
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
2
22
2
FD_EXTENDED_MAP_
2
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(20) Disp. 2 no measure values / (21) Dsp. 1 no measure
values / (28) IO B No Value for Binary Output / (29) IO B No
Value for Current Output / (30) IO A No Value for Binary
Output / (31) IO A No Value for Current Output
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
3
33
3
FD_EXTENDED_MAP_
3
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
4
44
4
FD_EXTENDED_MAP_
4
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
5
55
5
FD_EXTENDED_MAP_
5
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
6
66
6
FD_EXTENDED_MAP_
6
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
7
77
7
FD_EXTENDED_MAP_
7
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
8
88
8
FD_EXTENDED_MAP_
8
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
9
99
9
FD_EXTENDED_MAP_
9
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
10
1010
10
FD_EXTENDED_MAP_
10
RAn optional parameter to allow the user finer control on
enabling conditions contributing to the conditions in
FD_*_ACTIVE parameter.
Uninitialized
Setting:
(00) Reserved
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value

4 OPERATION
20
UFC 400
www.krohne.com 12/2015 - 4002813702 - AD FF UFC 400 R02 en
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
11
1111
11
FD_EXTENDED_MAP_
11
R/W Field Diagnostics of "Process : Signal Unreliable" Uninitialized
Setting:
(28) Time of Flight / (29) Path 3 unreliable /
(30) Path 2 unreliable / (31) Path 1 unreliable
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
12
1212
12
FD_EXTENDED_MAP_
12
R/W Field Diagnostics of "Process : Signal Lost" Uninitialized
Setting:
(29) Signal lost path 3 / (30) Signal lost path 2 /
(31) Signal lost path 1
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
13
1313
13
FD_EXTENDED_MAP_
13
R/W Field Diagnostics of "Process : Empty Pipe" Uninitialized
Setting:
(31) Empty Pipe
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
14
1414
14
FD_EXTENDED_MAP_
14
R/W Field Diagnostics of "Electronics : IO Connection" Uninitialized
Setting:
(28) IO B Connect. Control Input / (29) IO B Connect. Current
In-/Output / (30) IO A Connect. Control Input / (31) IO A
Connect. Current In-/Output
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
15
1515
15
FD_EXTENDED_MAP_
15
R/W Field Diagnostics of "Process : Current input" Uninitialized
Setting:
(30) IO B Error Current / (31) IO A Error Current
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
16
1616
16
FD_EXTENDED_MAP_
16
RField Diagnostics of "M Process" Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
17
1717
17
FD_EXTENDED_MAP_
17
R/W Field Diagnostics of "M Configuration" Uninitialized
Setting:
(30) Backup 2 Data Faulty / (31) Backup 1 Data Faulty
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
18
1818
18
FD_EXTENDED_MAP_
18
R/W Field Diagnostics of "M Electronics" Uninitialized
Setting:
(29) Backplane Difference / (30) Factory Data Faulty / (31)
Backplane Data Faulty
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
19
1919
19
FD_EXTENDED_MAP_
19
RField Diagnostics of "M Sensor" Uninitialized
Setting:
(00) Reserved
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
20
2020
20
FD_EXTENDED_MAP_
20
R/W Field Diagnostics of "S Process" Uninitialized
Setting:
(31) Velocity Out of Range
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
21
2121
21
FD_EXTENDED_MAP_
21
R/W Field Diagnostics of "S Configuration" Uninitialized
Setting:
(03) IO B Overrange Binary Output / (04) IO B Overrange
Current Output / (05) IO B Overrange Current In-/Output / (06)
IO A Overrange Binary Output / (07) IO A Overrange Current
Output / (09) IO A Overrange Current In-/Output
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
22
2222
22
FD_EXTENDED_MAP_
22
R/W Field Diagnostics of "S Electronics" Uninitialized
Setting:
(29) Conv. Zero too large
FD_EXTENDED_MAP_
FD_EXTENDED_MAP_FD_EXTENDED_MAP_
FD_EXTENDED_MAP_
23
2323
23
FD_EXTENDED_MAP_
23
RField Diagnostics of "S Sensor" Uninitialized
Setting:
(00) Reserved
Parameter
ParameterParameter
Parameter
DD name
Access Description and settings Initial Value