KTC MCCU14 User manual

1/ 4
Application
Thank you for purchasing DRIVE CHAIN TOOL SET (MCCU14).
In order to use this product safely and correctly, please be sure to read this Instruction Manual
before use. Please store it with the product.
Do not use the product except original intended purpose.
Do not use the product when the product or object to be worked on is defective in any way
such as it has crack or distortion.
Do not use the product for power tool such as impact wrench.
Each bolt is applied molybdenum grease. As for use this product longer, remove dirt and
dust etc. completely and apply molybdenum grease to each bolt again.
For chain sizes: 420・428・520・50(530)・532・630・632
This tool can be used for most domestic motorcycles.
Based on strength analysis, the design is in an optimum shape for durability and lightness
that even professional will approve.
Highly durable cutter pin & caulk pin is made from heat-treated special steel (SK type).
These parts have been designed to facilitate workflow.
・Bolt removal is not required as cutter pins can be replaced from the front of the inner bolt.
・The cutter pin can be used frequently in 40-50 series.
・Press fitting is designed for all sizes (press fitting caulk receiving plate), and as it can also
be used in caulking, this allows for a much smoother operation.
The inner bolt does not need to be set after the joint pin has been removed as the plate
press fitting uses the same outer bolt.
The grip and handle are designed so that strength may be applied easily.
A drive tool such as a separate 3/8”sq. ratchet tool is required when using this tool.
For motorcycle drive chain replacements, removing chain pin,
press fitting joint plates (including clip type) and caulking
joint pins.
Characteristics
DRIVE CHAIN TOOL SET
INSTRUCTION MANUAL

2/ 4
Structure and Part Names
#
No
.
o.
..
Item Number
Product
Main body
Outer Bolt
Ｉnner Bolt
Handle
For Cutter pin 4050
For Cutter guide 4050
For Cutter pin 60
For press fit plate 40
For press fit plate 52
For press fit plate 50
For press fit plate 60
Press Fit Caulking Receival Plate
Caulking pin
How to use
Removing chain
In case of 40, 50
In case of 60
①Ｉｎｓｅｒｔ ｃｕｔｔｅｒ ｐｉｎ 4050 ｉｎｔｏ Ｉｎｎｅｒ Ｂｏｌｔ
ａｎｄ Ｆｉｘ Ｉｎner Bolt into Outer Bolt.
For cutter pin
4050
Inner Bolt
②Install For cutter guide 4050 to Outer Bolt.
For cutter guide
4050
Outer Bolt
Inner Bolt
For cutter pin 60
Outer Bolt
①Insert cutter pin 60 into Inner Bolt and fix in Outer Bolt.

3/ 4
Chain
Cutting Receival plate
④Tighten Inner Bolt with3/8”sq.rachet handle etc. and
remove Chain pin.
SPARE PARTS
Though the product number of any parts of this page is
GOD-XXXX, “GOD-“is omitted to save space in the picture.
Pressing in of Joint Plate
Outer Bolt
Inner Bolt
Inner Bolt
Chain
Chain
Chain
Outer Bolt
Inner Bolt
Outer Bolt
Press Fit Caulking
Receival Plate
3/8”sq. Ratchet handle
3/8”sq. Ratchet handle
Outer Bolt
For cutter
guide 4050
Cutter Receival Plate
Outer Bolt
Outer Bolt
Outer Bolt
Joint Plate
Joint pin
Press Fit Plate
Press Fit Caulking
Receival Plate
Press Fit Plate
Cutter Receival
Plate
Roller Ring
Be careful not too tight when pressing in.
③Tighten the Outer Bolt by fingers, and maintain the pin
of the chain which is cut with the hole part of the Main
body Cutting Receival Plate and the hole part of For cutter
guide 4050.
③Tighten Inner Bolt with3/8”sq.rachet handle etc. and
remove Chain pin.
②Tighten the Outer Bolt by fingers, and maintain the pin
of the chain which is cut with the hole part of the Main
body Cutter Receival Plate and the hole part of the Outer
Bolt.
①Remove Inner Ｂｏｌｔ and in case of 40, 50, remove Inner
Bolt For Cutter guide 4050 which is used when cutting.
③Apply grease etc. to the depressed portion of
Press fit plate, and put Joint Plate on it.
②. Install Press Fit Caulking Receival Plate on Main body,
and suitable Press fit plate for chain on Outer Bol.
Adaptation size
④Connect Chain to Joint Pin, and fit the back of the
Joint Pin into the depressed portion of Press Fit
Caulking Receival Plate. Then, Tighten Outer Bolt by
fingers and make sure that Joint Pin and the hole of
the Joint Plate are fitted.

4/ 4
Pressing in fit of Joint Plate
Outer Bolt
Handle
Outer Bolt
Outer Bolt
Outer Bolt
Outer Bolt
Chain
Joint pin
Joint pin
Handle
Caulking pin
Press Fit Plate
Press Fit Plate
Caulking pin
Press fit plate
Until hitting
Until hitting
⑤Place Handle onto Outer Bolt, and tighten it until both
ends of the Press fit plate hit the next plate.
・Spreading too thin causes cracks.
・This product is for Flare caulking exclusive use. Cannot use for Cruciform caulking.
・
③Place Joint pin on the centre of Press Fit Caulking Receival Plate,
and make the pinpoint of Caulking pin and Joint pin stick together by
tightening Outer Bolt by hand.
①Uninstall the press fit plate is used when pressing in. Use Press
Fit Caulking Receival Plate as Caulking Receival Plate.
②Install Caulking pin on edge of Outer Bolt .
④Place Handle onto Outer Bolt, and tighten it until
the point of the joint pin extends.
Caulking condition