KTI KC-201-W3-S3 User manual

-1-
100BASE-TX TO 100BASE-FX
Single Fiber Media Converters
P/N750-0156-001
DOC.010801-KC201-NK
KC-201-W3-S3
KC-201-W5-S3
InstallationGuide

-2-
The information contained in this document is subject to change without
prior notice.Copyright ãAll Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
FCC NOTICE
This device complies with Class A Part 15 the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received including the interference that may cause.
CE NOTICE
Marking by the symbol indicates compliance of this equipment to
the EMC directive of the European Community. Such marking is indica-
tive that this equipment meets or exceeds the following technical stan-
dards:
EMC Class A
EN 50081-1/1992 : EN55022, EN61000-3-2, EN61000-3-3
EN 50082-1/1998 : EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5,
EN61000-4-6, EN61000-4-11
Table of Contents
1. Introduction.........................................................3
1.1 Specifications ................................................................................ 4
2. Installation...........................................................5
2.1 Unpacking ..................................................................................... 5
2.2 Media Converters .......................................................................... 5
2.3 LED Indicators............................................................................... 6
2.4 Applying Power .............................................................................. 6
2.5 Making Connection........................................................................ 7

-3-
1. Introduction
The100BASE-TXto100BASE-FXsinglefibermediaconverterseriesprovides
a media conversion allowing high-speed integration of fiber optic and twisted-
pair segments.
With WDM technology, the converters uses one single fiber cable instead of
duplexfibercablefordatatransmission. AcompletesetofLEDsallowsforquick
status verification.
The converters also provide the following key features:
• Compliancewith IEEE 802.3ustandard
• Auto-negotiation function built in twisted-pair port that allows to
operate at optimal configuration connecting to an auto-negotiation
capable device
• Extending network span up to 30km over dual wavelength single
strand single mode fiber cabling
• Tremendous cost saving of single mode optic fiber cable
• Providing both MDI jack and MDI-X jack on the twisted-pair
interface for flexible UTP cable selection
The converter series support the following configuration needs:
100BASE-TXto100BASE-FXsinglemodeSC(30Km)
KC-201-W3-S3 Tx1310nm,Rx1550nm
KC-201-W5-S3 Tx1550nm,Tx1310nm

-4-
1.1 Specifications
Twisted-PairInterface
Connectors TwoShielded RJ-45jacks
Pin Assignments MDIand MDI-X
Compliance IEEE802.3u100BASE-TX
Data Speed 100Mbps
Duplex Mode Half-duplexorFull-duplex
Cable Type 100Mbps - Category 5 UTP
Supported Link Length 100meters
FiberOpticInterface
Compliance IEEE802.3u100BASE-FX
Connector SimplexSC
Data Speed 100Mbps
Duplex Mode Full-duplex
Cable Types Singlemode(SM)-8.7/125,9/125,10/125mm
GeneralInformation
Frame Types Supported IEEE802.3Std.64Bytes~1518Bytesframes
& VLAN tagged frames (4 bytes tag)
Power DC Input +12V0.8Amin.
Dimension H28mmxW96mxD151mm
Housing Enclosed metal with no fan
Operating Temperature 0oC~50oC
Storage Temperature -20oC~90oC
RelativeHumidity 5%~ 90%

-5-
2. Installation
2.1 Unpacking
Check that the following components have been included:
• Installation guide
• 100Single Fiber MediaConverter
• One AC power adapter for the converter
2.2 Media Converters
FunctionsofUTPPort(Twisted-PairInterface)
• Auto-negotiation support for connecting to 100M auto-negotiation
devices
• Supports both of half duplex and full duplex operations
• MDI and MDI-X jacks are provided for flexible selection of UTP
connection
Functionsof100BASE-FXPort(FiberOpticInterface)
• Full data rate of 100Mbps for remote fiber connection
• Full-duplexoperation
• Singlemode Single fiber SC interface(up to30Km)
Model Tx Wave Rx Wave Outputpower InputSensitivity
KC-201-W3-S3 1310nm 1550nm -7 dBm -23dBm min.
KC-201-W5-S3 1550nm 1310nm -7 dBm -23dBm min.

-6-
DCInputJack
DC Input +12VDC
DCPower min.0.8A
DC Input Jack
2.3 LED Indicators
Name Status State Interpretation
POWER Power status On Power on
Off Power off
UTP UTP link & Rx status On Link up
Off Link down
FX Fiber link & Rx status On Link up
Off Link down
Note: UTP & FX LED blink to off for 0.1 second for every received packet
2.4 Applying Power
Before you begin the installation, check the AC voltage of your area. The
ACpoweradapterwhichis used tosupply theDC powerfortheunitshould
have the AC voltage matching the commercial power voltage in your area.
The specifications of the AC power adapter are:
• AC input power: AC power voltage of your area
• DC output power: +12VVDC0.8Aminimum
1. Connect power adapter DC plug to the DC input jack located on the
back of the converter before connecting to the AC outlet.
2. Connect the power adapter to the AC outlet.
3.Check Power LEDindication.

-7-
2.5 Making Connection
The converters must be used in pair of 201-W3-S3 and 201-W5-S3. Both
use different wavelengths to transmit and receive data. See the following
example:
The figure below shows the configuration used when connecting to
auto-negotiation device and non-auto-negotiation device.
For proper communication, the UTP connections on both ends must be
insame configuration,either 100M full-duplex or 100M half-duplex.