Kusam-meco KM-2006 User manual

Preliminary Data
An ISO 9001:2008 Company
Model KM 2006
NEW
GENERAL SPECIFICATIONS :
FEATURES :
0.1 mA Current Resolution.
True RMS Measurement for all applications.
Backlight function.
MAX MIN measurement function.
Data Hold function &
CAT IV 300V.
Auto Power Off.
Autoranging.
—
—
— LED
—
—
—
—
—
Zero function.
Display : 4 Digit 5000 counts liquid crystal LCD display.
Jaw size : 23mm.
Sampling rate : 2 times/sec.
Accessories : Test lead, User manual, Batteries & Carrying case.
—
—
—
—
—
—
—
—
—
—
—
—
Operating Temperature & Humidity : 0 ~ 40°C (32 ~ 104°F); < 80% RH.
Storage Temperature & Humidity : -10 ~ 60°C (14 ~ 140°F); < 80% RH.
Low battery indication.
Continuity < 100W.
Auto power off 30 minute.
Power Supply : 1.5V AAA battery x 2.
Dimension : 206(L) x 76(W) x 33.5(H)mm
Weight : Approx. 270g.
ELECTRICAL SPECIFICATIONS :
All Specifications are subject to change without prior notice.
G-17, Bharat Industrial Estate, T. J. Road, Sewree (W), Mumbai - 400 015. INDIA.
Sales Direct.: 022-24156638, Tel. : [phone], Fax : [phone]
Email : [email protected], Website : www.kusamelectrical.com
An ISO 9001:2008 Company
®
Chhaya com/D/chhaya/my documents/chhaya/backup/catlog/New catlog/2015 new arrival catalogs/KM 2006.cdr
300.0 mA
3000 mA
10.00 A
± (1%rdg + 10dgts)
DC CURRENT
Accuracy
Resolution
Range
0.1 mA
1 mA
0.01 A
300.0 mA
3000 mA
20.00 A
± (1%rdg + 5dgts)
AC CURRENT
Accuracy
Resolution
Range
0.1 mA
1 mA
0.01 A
50 V
300 V ± (1%rdg + 2dgts)
0.01 V
0.1 V
DC VOLTAGE
Accuracy
Resolution
Range
50 V
300 V ± (1%rdg + 5dgts)
0.01 V
0.1 V
AC VOLTAGE
Accuracy
Resolution
Range
500 W
5 KW± (1%rdg + 2dgts)
0.1 W
1 W
OHM
Accuracy
Resolution
Range
50 KW
500 KW
10 W
100 W
AC/DC TRMS LEAKAGE
CLAMPMETER

17, Bharat Industrial Estate, T. J. Road, Sewree (W),
Mumbai-400015. INDIA
Sales Direct: 24156638 Tel.:[phone] Fax:[phone]
E-mail : [email protected], Website : www.kusamelectrical.com
www.kusam-meco.co.in
Digital Multimeter
Digital AC & AC/DC Clampmeter
AC Clamp Adaptor
AC/DC Current Adaptor
Transistorised Electronic Analog & Digital
Insulation Resistance Testers
Digital Sound Level Meter & Sound Level
Calibrator
Digital contact & Non-contact Type
Tachometer
Digital Non-contact (infrared) Thermometer
Thermo Hygrometer
Thermo Anemometer
Wood Moisture Meter
Distance Meter
Digital Hand Held Temperature Indicators
Digital Lux Meter
Network Cable Tester
Power Factor Regulator
Maximum Demand Controller/Digital Power
Meter
LIST OF PRODUCTS
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
OPERATION
MANUAL
KM-2006
MILLIAMP CLAMP
METER

WARRANTY
14
KM 2006
MILLIAMP CLAMP METER

Table of Contents
1. SAFETY INFORMATION................................1
2. GENERAL SPECIFICATION............................1
3. Electrical SPECIFICATION.............................. 2
3.1 Direct Voltage ..............................................3
3.2 Alternating Voltage ......................................3
3.3 Direct Current ..............................................3
3.4 Alternating Current ......................................3
3.5 Resistance(W) .............................................3
3.6 Continuity ( ) ...............................................3
4. DESCRIPTION OF THE INSTRUMENT...........4
4.1 Description of the display..............................4
4.2 Description of front & rear.............................5
5.BUTTON INSTRUCTION..................................6
5.1 HOLD Function.............................................6
5.2 MAX/MIN Function ......... ............................6
5.3 ZERO Function ...........................................6
5.4 BACKLIGHT Function..................................6
6. MEASURING INSTRUCTION .........................7
6.1 ACA Measurement........................................8
6.2 DCA Measurement ......................................9
6.3 ACV Measurement ......................................11
6.4 DCV Measurement.......................................11
6.5 Continuity Measurement .............................11
6.6 Resistance Measurement.............................11
7. BATTERY CHANGING.....................................11
8. MAINTENANCE ..............................................12
9.TEST CERTIFICATE........................................13
10.WARRANT .....................................................14
Title Page
2. GENERAL SPECIFICATIONS
1
1. SAFETY INFORMATION
!
Do not operate the tester if the body of meter or the
test lead look broken.
Check the main function dial and make sure it is at
the correct position before each measurement.
Do not perform resistance and continuity test on a
live power system.
Do not apply voltage between the test terminals and
test terminal to ground that exceed the maximum
limit record in this manual.
Keep the fingers after the protection ring when mea-
suring through the test lead.
Chang the battery when the symbol appears to
avoid incorrect data.
+
Environment Conditions
Operation Temperature : 0°C to 40°C (32°F to 104°
F); 80%RH
V
Storage Temperature : -10°C to 60°C (14°F to 140°
F); 80%RH
V
Explanation Symbols
Attention refer to operation Instructions.
Dangerous voltage may be present at terminals.
This instrument has double insulation.
!
Approvals: C C En61010 300V CAT IV
Digital Display : 4 digital liquid crystal (LCD),
Maximum reading 5000.
Polarity : When a negative signal is applied, the
signal appears.

2
Low Battery Indication : When the battery is under
the proper operation range, will appear on the
LCD display.
Sample Rate : 2 times/sec for digital data.
Power Source: 1.5V size AAA battery X 2
Typical battery Life: (without buzzer, backlight)
Type: 15 hours at DCA function;
60 hours at ACA and ACV function:
100 hours at DCV and Ohm function.
Auto Power Off : If there is no key or dial operation
for 30 minutes, the meter will power itself off to save
battery consumption. This function can be disabled
by press and hold the HOLD " button then power the
unit on
Over Load: When the signal larger than the maximum
will be show 0L.
Maximum jaw opening: 23mm
Dimensions: 206 x 76 x 33.5 mm
Weight : 262g (with battery)
Accessories: Carrying case. Batteries, Test Lead &
Instruction Manual.
3. ELECTRICAL SPECIFICATION
The accuracy specification is defined as ± ( percent
of reading + digit ) At 23±5°C, 80 %RH.
V
=
3.1 Direct Voltage
Range Resolution Accuracy
50V / 300V 0.01V/0.1V 1.0% + 2dgts
Input impedance: 1 MW
3
3-2 Alternating Voltage (True RMS)
Range Resolution Accuracy(40~1KHz)
50V / 300V 0.01V/0.1V 1.2% ± 5dgts
Input impedance: 1 MW
3-3 Direct Current
Range Resolution Accuracy
300.0mA
3.000A
10.00A
Influence of terrestrial magnetism : Less than ± 1.0mA
Influence of CT opening & closing : Less than ± 1.0mA
0.1mA
0.001A
0.01A
1.0% + 10dgts
3.0% + 10dgts
3-4 Alternating Current (True RMS)
0.1mA
0.001A
0.01A
1.0% + 5dgts
Range Resolution Accuracy
300.0mA
3.000A
20.00A
0.1W
1W
10W
100W
1.0% + 2dgts
Range Resolution Accuracy
500W
5KW
50KW
500KW
3-5 Resistance (W)
3-6 Continuity
Range Buzzer Function
Ohm 100W
V

4
~
4.DESCRIPTION OF THE INSTRUMENT
4-1 Description of The Display
+
A
V
ZERO
HOLD
MAX
MIN
K
W
m
Auto power off indication
Polarity indication
Low battery indication
Alternative source indication
Direct source indication
Current measurement indication
Voltage measurement indication
ZERO indication
Data hold indication
Maximum indication
Minimum indication
Continuity test indication
Measurement unit
Resistance measurement indication
Measurement unit
5
4-2 Description of Front And Rear
1. Current Sensing Clamp
2. Safety protection ring
3. Backlight button
4. Clamp opening handle
5. Function select dial
6. ZERO button
7. Max/Min button
8. Data hold button
9 LCD display
10. COM input terminal
11. Positive input terminal
12. Battery cabinet

6
5. BUTTON INSTRUCTION
5-1. HOLD Function
It is possible to freeze the value displayed by pressing
on the “HOLD” button.
Press the “HOLD” button again to exit the Hold mode.
5-2. MAX/MIN Function
When the “MAX/MIN” button is pressed, the meter
enter MAX/MIN mode.
Press the button, to read MAX, MIN sequence. Press
the button for 1 sec. or more to exit the MAX/MIN
mode.
When you turn the rotary switch on the Continuity
Test.
Press the “MAX/MIN” button to select Resistance
measurement,
Press the “MAX/MIN” button again to select
continuity test with buzzer.
5-3. ZERO Function
Press “ZERO” button to enter the Zero mode, ZERO
Annunciate will appear and Zero the display. The
reading is stored as reference value for subsequent
measurement.
5-4 BACKLIGHT Function
When the “ ” button is pressed, the backlight will be
turned on.
To disable the function, the button is pressed again.
The backlight will be automatically turned off about
30 seconds after it turned on.
7
6. MEASURING INSTRUCTION
6-1 ACA Measurement : With the clamp disconnected
from any conductor, switch the function selector to
A range.
~
Open the clamp by pressing the jaw-opening handle
and insert the Cable to be measured into the jaw.
Close the clamp and get the reading from the LCD
panel.
Note :
Before this measurement, disconnect any test lead
with the meter for safety.
In some cases where reading is difficult, press the
HOLD button and read the result later.

!
9
Switch the main function selector to V range.
~
Connect red test lead to “+” terminal and black one to
the “COM” terminal.
Measure the voltage by touch the test lead tips to the
test circuit where the value of voltage is needed.
Read the result from the LCD panel.
6-4 DCV Measurement :
Switch the main function selector to V range.
~
Connect red test lead to “+” terminal and black one to
the “COM” terminal.
Measure the voltage by touch the test lead tips to the
test circuit where the value of voltage is needed.
Read the result from the LCD panel.
8
6.2 DCA Measurement :
With the clamp disconnected from any conductor,
switch the function selector to A range.
—
---
Press “ZERO” button to enter the zero reading.
Open the clam by pressing the jaw-opening handle
and insert the cable to be
measured into the jaw. close the clamp and get the
reading from the LCD panel.
Note : Before this measurement, disconnect any test
lead from the meter for safety.
In some cases where reading is difficult, press the
“HOLD” button and read the result later.
6-3 ACV Measurement :
WARNING !
!
Maximum Input Voltage is 300V AC/DC. Do not attempt
to Take any voltage measurement that may exceed this
maximum to avoid Electrical shock hazard and/or damage
to this instrument.

10
Connect tip of the test leads to the point where the
conduction condition needed.
If the resistance is under 100W, the beeper will sound
continuously.
6-5 Continuity Test With Buzzer :
Switch the main function to W range.
Connect red test lead to “+” terminal and black one to
the “COM” terminal.
6-6 Resistance Measurement
Switch the main function to W range.
Connect red test lead to “+” terminal and black one to
the “COM” terminal.
Connect tip of the test leads to the point where the
value of the resistance is needed.
Read the result from the LCD panel.
11
7. BATTERY CHANGING
When the battery voltage drop below proper operation
range the symbol will appear on the LCD display and
the battery needs to be changed.
Before changing the battery, switch the main dial to
“OFF” and disconnect test leads.
Open the back cover by a screwdriver.
Replace the old batteries with two new 1.5V (AAA
size) battery.
Close the back cover and fasten the screw.

Before open the meter, disconnect both test lead
& never uses the meter before the cover is closed.
To avoid contamination or static damage, do not
touch the circuit board without proper static protection.
• If the meter is not going to be used for a long time,
take out the battery and do not store the meter in
high temperature or high humidity environment.
• When take current measurement, keep the cable at
the center of the clamp will get more accurate test
result.
• Repairs or servicing not covered in this manual
should be performed only by qualified personal.
Periodically wipe the case with a dry cloth. Do not
use abrasives or solvents on these instruments.
12
8. MAINTENANCE
WARNING !
!
CAUTION !
8-1 REMARK :
8-2 CLEANING :
TEST CERTIFICATE
MILLIAMP CLAMP METER
This Test Certificate warranties that
the product has been inspected and
tested in accordance with the published
specifications.
The instrument has been calibrated by
using equipment which has already
been calibrated to standards traceable
to national standards.
MODEL NO. ___________
SERIAL NO. ___________
DATE: ___________
ISO 9001
REGISTERED
13
MUMBAI
KM 2006
QC
PASS
KUSAM-MECO