KYMCO Compagno 110i User manual

To avoid damage from the scooter's electronic fuel injection system, do not remove or
install the battery when the ignition switch is at the "ON" position.
The petrol could be caused the effects of deterioration from non-use or extended storage of the
vehicle that would cause the non-start situation. Service more frequently when operating in severe
conditions: environment, high speed frequent starting/stopping usage or extreme riding habit.
Make sure flammable materials such as dry glass or leaves do not come in contact with the
exhaust system when parking your scooter.
,
To avoid damage from the scooter's electronic fuel injection system, do not remove or
install the battery when the ignition switch is at the "ON" position.
The petrol could be caused the effects of deterioration from non-use or extended storage of the
vehicle that would cause the non-start situation. Service more frequently when operating in severe
conditions: environment, high speed frequent starting/stopping usage or extreme riding habit.
Make sure flammable materials such as dry glass or leaves do not come in contact with the
exhaust system when parking your scooter.
,
WARNING

This Owner’s Manual contains important information on safety, operation and maintenance of your KYMCO
scooter. Any one who operates your scooter should carefully read and understand the
contents of this manual before riding the scooter. For your safety, understand and follow all of the warnings
contained in this Owner’s Manual and the labels applied to your scooter. This Owner’s Manual should be
considered a permanent part of the vehicle, keep it with your scooter at all times. ON-ROAD USE ONLY This
scooter has been designed to be used on the road.
100iCompagno
Read this manual carefully.
The NOTE symbol indicates key information about a procedure or to clarify
an operation.
The SAFETY ALERT symbol with the exclamation point in the triangle
meansATTENTION! BE ALERT! YOUR SAFETY CAN BEAFFECTED.
Failure to follow instructions associated with a WARNING symbol could
result in severe injury or death to the rider, a passenger, a bystander, or a
person inspecting or repairing the scooter.
A CAUTION symbol indicates that special precautions must be taken to
avoid damaging the scooter.
NOTE
WARNING
CAUTION
Particularly important information is called out in this manual by the following icons
and notations:

Identification Numbers Record
1
Record the Vehicle Identification Number (VIN) and Engine Serial Number in the boxes above for future
reference (to assist you in ordering parts from your authorized KYMCO dealer or for reference in case the
vehicle is stolen).
2. ENGINE SERIAL NUMBER (ESN)
1. VEHICLE IDENTIFICATION NUMBER (VIN)
1 2
2

TABLE OF CONTENTS
SECTION 1 - SAFETY .............................1-7
Forward .........................................................1
Scooter Safety.............................................2 - 3
Accessories & Modifications.............................4
Locations of Parts & Controls.........................5 - 7
SECTION 2 - CONTROLS & FEATURES.8 - 15
Ignition Switch ................................................8
Security shutter...............................................9
Instruments...................................................10
Right-hand Handlebar Switch..........................12
Left-hand Handlebar Switch............................12
Fuel Recommendation...................................14
Seat.............................................................15
SECTION 3 - OPERATION.......................16 - 18
Pre-ride Inspection........................................16
Starting the Engine........................................17
SECTION 4 - MAINTENANCE...............19- 33
Maintenance Schedule.............................20 - 22
Engine Oil.....................................................23
Engine Oil Replacement.................................24
Transmission Fluid Change............................26
Air Filter Element Change...............................27
Throttle Operation..........................................27
Spark Plug....................................................28
Brake Fluid Level Inspection...........................29
Brake Lever Adjusters....................................30
Battery & Fuse...............................................32
Tires.............................................................33
How to adjust clock ...............................34
EMISSION CONTROL...........................35
SPECIFICATIONS..............................36
5
6
4
3
1
2
KYMCO SCOOTER
LIMITED WARRANTY.......37
7

SECTION 1 -
FORWARD & SAFETY INTRODUCTION
Thank you for purchasing this KYMCO scooter, and welcome to the KYMCO riding
family.
Please read this owner's manual carefully before riding so that you will be thoroughly familiar with the
proper operation of your scooter controls, its features, capabilities, and limitations.
To ensure a long, trouble-free life for your scooter, provide it with the proper care and maintenance as
described in this manual.
For replacement parts and accessories, you should always use genuine KYMCO products, as they have
been specially designed for your vehicle and manufactured to meet KYMCO's demanding standards.
Keep this owner's manual aboard your scooter at all times so that you can refer to it whenever you need
information. This manual should be considered a permanent part of the scooter and should remain with
the scooter when it is sold.
All information, illustrations, photographs and specifications contained in this manual are based on the
latest product information available at the time of publication. Due to improvements or other changes,
there may be information in this manual that differs slightly from your vehicle. KYMCO reserves the right to
make product and publication changes at any time without notice and without incurring any obligation.
Compagno 100i
1

SCOOTER SAFETY
Your scooter can provide you many years of
service and pleasure if you take responsibility for
your own safety and understand the challenges
that you can meet on the road. There is much that
you can do to protect yourself when you ride. You
will find many helpful recommendations
throughout this manual. Here are some very
important safety tips:
IMPORTANT SAFETY INFORMATION
Wear a helmet
Scooter safety equipment starts with a quality
helmet. One of the most serious injuries you can
suffer in a crash is a head injury. Always wear a
properly approved helmet. You should also wear
suitable eye protection.
Make yourself easy to see
To make yourself more visible, wear bright
reflective clothing, position yourself so other
drivers can see you, signal before turning or
changing lanes, and use your horn when it will help
others notice you.
Know your limits
Ride within the boundaries of your own skill at all
times. Knowing these limits and staying within
them will help you to avoid accidents.
For safe riding, it's important to inspect your
scooter before every ride and perform all
recommended maintenance. Never exceed load
limits, and only use accessories that have been
approved by KYMCO for this scooter.
Keep your scooter in safe condition
Do not forget to perform an entire safety inspection
to ensure you, and your passenger's safety, before
each ride.
Inspect your scooter before riding
Riding on bad weather days, especially wet ones,
requires extra caution. Braking distance can
double on a rainy day. Stay off of the painted
surfaces, manhole covers and greasy appearing
areas on the pavement, as they can be especially
slippery. Use extreme caution at railway crossings
and on metal gratings and bridges. Whenever you
are in doubt about the road conditions, slow down.
Be extra safety conscious on bad
weather days
Modification of your scooter, or removal of original
equipment may render the vehicle unsafe or illegal.
Obey all applicable equipment regulations in your
area.
Modification
2

1
SCOOTER SAFETY
For your safety, always wear an approved
motorcycle or scooter helmet, eye protection,
boots, gloves, long pants, and a long- sleeved shirt
or jacket whenever you ride your scooter.
PROTECTIVE APPAREL
Your helmet is your most important piece of riding
gear because it offers the best protection against
head injuries. Your helmet should fit your head
comfortably and securely. Always wear a face
shield or goggles to protect your eyes and to aid
your vision.
Helmets and protection
In addition to a helmet and eye protection, you
should also use:
Additional riding gear
Sturdy boots with nonslip soles to help protect your
feet and ankles.
Leather gloves to keep your hands warm and help
prevent blisters, cuts, burns and bruises.
A motorcycle or scooter riding suit or jacket that has
been designed for comfort as well as protection.
Bright colored and reflective clothing can help make
you more noticeable in traffic. Be sure to avoid loose
clothes that could get caught on any part of your
scooter.
Wear gloves
Clothes should be fit properly (not too tight or
loose)
Always wear a helmet. You should also wear
eye protection
Wear bright or reflective clothing
Footwear should be the proper size, have low
heels, and offer ankle protection
Not wearing a helmet increases your
chance of serious injury or death in a
crash.
WARNING
Be sure you and your passenger always
wear an approved motorcycle helmet
that fits properly. You should also wear
eye protection and other protective
apparel when you ride.
WARNING
4
3
2
1
5
3

4
ACCESSORIES & MODIFICATION
There is a large variety of accessories available to KYMCO scooter owners. KYMCO cannot have direct
control over the quality or suitability of accessories you may wish to purchase. The addition of unsuitable
accessories to your scooter can lead to unsafe operating conditions. It is not possible for KYMCO to
test each accessory on the market or combinations of all the available accessories; however, your
KYMCO dealer can assist you in selecting quality accessories and then install them correctly.
Use extreme caution when selecting and installing the accessories for your
scooter.
No modifications
KYMCO strongly advises you against removing any original equipment or modifying your scooter in any
way that would change its design or operation.
WARNING
WARNING
WARNING
WARNING
WARNING
Improper accessories or modifications can make your scooter unsafe and can lead to an accident.
Never modify your scooter through the improper installation or use of accessories. All parts and
accessories added to this vehicle should be genuine KYMCO or equivalent components designed for use
on this scooter and should be installed and used according to instruction. If you have any questions,
consult an authorized KYMCO dealer.
WARNING

5
LOCATIONOFPARTS&CONTROLS
Taillamp/Stoplamp
6
7
Air Filter
8
9
Side Stand
Engine Number
11
Helmet Buckle
Headlamp
1
Front Left Turn Signal Lamp
2
Rear Left Turn Signal Lamp
3
Rear Brake Lever
4
5
NOTE: Your scooter may differ slightly in appearance from the images in this manual.
1
10
Vehicle Identification Number(VIN)
Fuel Filler Cap
24
3 5
11
6 8 7
10
9

6
LOCATIONOFPARTS&CONTROLS
NOTE: Your scooter may differ slightly in appearance from the images in this manual.
Ignition Switch
16
14
17
18
Oil Filler Cap/Dipstick
15
Front Brake Lever
19
Muffler
20
Rear Passenger Footpeg
17
15 12
13
16 19 18 21 1420
21
Center Stand
Front Luggage Hook
Middle Luggage Hook
Front Right Turn Signal Lamp
Rear Right Turn Signal Lamp
13
12

7
LOCATIONOFPARTS&CONTROLS
NOTE: Your scooter may differ slightly in appearance from the images in this manual.
24
Left HandleBar Switch
Right Handlebar Switch
24
23
Instruments
22
232225
25
Position Lamp

8
SECTION 2 -
CONTROLS&FEATURES
To operate the ignition switch and it s functions:'
IGNITION SWITCH
All electrical circuits are off. The engine will not
start or run.
“ ” Position:
The ignition circuit is "ON" and engine can now be
started. The key can not be removed from the
ignition switch in this position.
“ ” Position:
“ ” Position:
To lock the steering, turn the handlebar all the way
to the left, push down and turn the key to the " "
position and remove the key. All electrical circuits
are off.
“ ” Position:
With the ignition key at the " " position (the
engine is running), push the key in and turn it
counterclockwise from " " to the position.
""
With the ignition key in the " " position (the
engine is not running), turn the counterclockwise
from the " " to the position.
Pull up on the back portion of the seat to lift it up.
""
To open the fuel filler cap, turn the key to the " "
position. Make sure that the key is at the " "
position when starting the engine.
“ ” Position:

9
CONTROLS & FEATURES
Push the shut-button on the ignition switch cover
and then the shutter should be closed.
To open the ignition switch security
shutter:
To shut the ignition switch security
shutter:
Insert the specific key until the fillister is
facing the pin.
Turn clockwise and then the security shutter
should be opened.
The keys have a unique code that is stamped on
the tab supplied with the keys. This code is not
stamped on the scooter and is not recorded in the
vehicle's basic documentation for security
reasons. Since this code is required if you need
replacement keys, record this important code in
the box provided on the inside, rear cover of this
Owner's Manual.
SECURITY SHUTTER

10
CONTROLS & FEATURES
Instruments
Odometer/Tripmeter: Press the mode button
to toggle between the overall and trip mileage,
or to reset the tripmeter.
""
Press the “ADJ.” button for two second, then
displays the ODO, TRIP or empty mode.
Press the “ADJ.” and “MODE” button
simultaneously at the TRIP mode, then the
figure reset automatically.
MODE ADJ.
Speedometer: Indicates the road speed in K/PH
(kilometers per hour).
Turn Signal Indicator Light: Flashes when either
turn signal is being used.
High Beam Indicator Light:This light is
illuminated when the headlight high beam is on.
Clock
Fuel refill indicator “ “: This indicator lights
when the fuel tank is near empty to alert the rider
to refill the fuel tank as soon as possible.
1
2
34
56

11
CONTROLS & FEATURES
CELP indication: If flashing, it indicates that a
fault has been detected in the scooter’s EFI or
electrical system. Requires immediate
inspection by a KYMCO dealer.
Press the ADJ. button for two second, then
displays the ODO TRIP or empty mode.
Press the ADJ. and MODE button
simultaneously at the empty mode, then the
indicator go out automatically.
,
NOTE: The CELP indicator lights momentarily
when the scooter is turned ON before the
engine is running.
,
Oil service indicator: Lights when the scooter
has reached the oil service interval mileage.
The indicator also lights when the ignition is
turned ON but should go out once the engine is
running.
8
Battery voltage too low warning Indicator:
While user starting the engine, if the battery
voltage is too low. The indicator will Bright light.
Reminded user wanted to charge or replace new
battery .
MODE ADJ.
78
7
9
9

12
CONTROLS & FEATURES
Right handlebar switch
Electric starter button " " position:
Press the electric starter button to activate the
starter motor.
NOTE: The starter motor will not engage unless
a brake lever is squeezed at the same time the
starter button is pressed.
Left handlebar switch
Turn signal switch :
Use the turn signal indicator to signal to other traffic
your intention to turn or change lanes. The turn
signal light on the dash will flash to alert the rider
that the switch is engaged.
for turning to the "left".
for turning to the "right".
To cancel the turn signal, press the switch in when
it is in the center position.
""
""
Press the horn button to sound the horn.
Horn button :

13
CONTROLS & FEATURES
""
""
switch position turns the headlight low beam
on.
switch position turns the headlight high beam
on and the high beam indicator light on the dash is
activated as well.
Apply the rear brake only by squeezing the left
hand brake lever gently towards the grip. The
brake light will illuminate when the lever is
squeezed.
4
4
Apply the front brake only by squeezing the right
hand brake lever gently towards the grip. The
brake light will illuminate when the lever is
squeezed.
Rear brake lever (left handlebar)
Front brake lever (right handlebar)
Dimmer switch :

14
CONTROLS & FEATURES
If the low fuel indicator on the dash begins to
flash,refill the fuel tank with unleaded gasoline
as soon possible.
Use unleaded gasoline with a research octane
number of 91 or higher to prevent from spark plug
and exhaust component damaged.
After refueling, be sure to close the filler cap
securely.
Fuel level inspection / Refilling
Fuel tank filler :
Fuel recommendation
To add fuel to your scooter, follow this procedure:
Use the ignition key to unlock the cap.
Turn the key clockwise to the position “ “.
The fuel filler cap will open automatically. Fill the fuel.
Close the filler cap after filling the fuel.
1
2
3
4
1
3
4
2

15
3
CONTROLS & FEATURES
Seat
WARNING
Use the helmet buckles only when your scooter
is parked. Do not ride with a helmet hanging from
the holder.
With the ignition key at the " " position (the
engine is running), push the key in and turn it
counterclockwise from " " to the position.
With the ignition key in the " " position (the
engine is not running), turn the counterclockwise
from the " " to the position.
Pull up on the back portion of the seat to lift it up.
Helmet Buckles
To use the helmet buckles, open the seat and hook
your helmet's fastener ring to the buckles and
close the seat securely.
7
7
""
""
To unlock the seat

16
SECTION 3 -
OPERATION
Pre-ride inspection
For your safety, it is very important to take a few
moments before each ride to walk around your
scooter and check its condition. If you detect any
problem, be sure to address it immediately, or have
it corrected by your KYMCO dealer.
WARNING
Improperly maintaining your scooter or failing to
correct a problem before riding can cause a
crash in which you can be seriously hurt or killed.
Always perform a pre-ride inspection before
every ride and correct any problems.
Engine oil level: Add engine oil if required (page
23). Check for leaks.
Fuel level: Fill fuel tank when necessary (page
14). Check for leaks.
Front and rear brakes: Check operation, make
sure there is no brake fluid leakage (page 29).
Tires: Check condition and inflation pressure
(page 33).
Throttle: Check for smooth operation and that it
closes completely in all steering positions (page
27).
Lights and horn: Check that headlight, tail/brake
light, turn signals, indicators and horn function
properly.
Steering: Check for condition and smoothness.
1.
2.
3.
4.
5.
6.
7.