La Crosse 513-1311OT User manual

Model: 513-1311OT www.lacrossetechnology.com/support Page | 1
Large Atomic Digital Wall Clock
with Indoor/Outdoor Temperature and Date
Buttons
Model: 513-1311OT
Quick Setup Guide
DC: 041614
Time, Alarm, Time Zone + WWVB Reception Icon
Indoor Temperature, Month, Date,
Weekday + Outdoor temperature
Battery Compartment
3 “C” batteries
KW5012FSK
Temperature Sensor

Model: 513-1311OT www.lacrossetechnology.com/support Page | 2
Get Started
Step 1: Insert 3 “C” LR14 Alkaline batteries (not included) into the clock.
Observe the correct polarity.
Step 2: Insert 2 “AA” LR6 batteries into the outdoor sensor. Observe the
correct polarity. The red LED will flash when transmitting.
Restart: If the outdoor temperature is not displayed after 3
minutes, remove batteries from the clock & outdoor sensor. Press
any button on the wireless thermometer 20 times. After 15
minutes, return to Step 1 above.
Set Time, Calendar, DST Indicator
•Hold the MODE/SET button to enter the
setting mode.
•Press the +or –buttons to adjust a value.
•Press the MODE/SET button to confirm
adjustment and move to the next item.
Setting order:
1. Hour
2. Minutes
3. Seconds
4. Year
5. Month/Date format (M/D or D/M)
6. Month
7. Date
8. DST indicator
Note:The clock will default back to time display if no buttons are pressed
for 30 seconds.
Battery
Compartment
2-AA batteries
MODE/SET + 12/24 - °C/°F

Model: 513-1311OT www.lacrossetechnology.com/support Page | 3
Fahrenheit/Celsius Selection
Press the - °C/°F button to change the temperature display from
Fahrenheit to Celsius.
Time Zone Selection/12/24 Hour time Format
•Press the + 12/24 button to select 12 hour or 24 hour time
format. Default is 12 hour time.
•Hold the +12/24 button to select the time zone. There are
four time zones:
oP= Pacific
oM= Mountain
oC= Central
oE= Eastern
Alarm Set
•Press the MODE/SET button to enter
Alarm Mode. “AL” will show on the display.
•Hold the MODE/SET button to enter alarm
set mode.
•Press the +or –buttons to adjust a value.
•Press the MODE/SET button to confirm
adjustment and move to the next item
Setting Order:
1. Hour
2. Minutes
Activate/Deactivate Alarm
•Press the AL ON/OFF button to activate the alarm.
•The bell icon will appears when alarm is active.
•Press the ALARM ON/OFF button to deactivate the alarm.
•The bell icon will disappear.
Snooze
•When the alarm sounds, press the SNOOZE button to
trigger snooze alarm for 5 minutes.
•The snooze icon Zz will flash above the time.
•The snooze function can be repeated up to seven times.
- °C/°F
+ 12/24
MODE/SET + 12/24 - °C/°F
AL ON/OFF

Model: 513-1311OT www.lacrossetechnology.com/support Page | 4
Outdoor Temperature Alert
•Hold the ALERT button for 3 seconds to
enter high alert setting.
•Press the + or -button to select the high
alert value.
•Press the ALERT button to enter low alert setting.
•Press the + or -button to select the low alert value.
•Press and release the ALERT button to confirm and
exit.
•Press the ALERT button to turn the outdoor
temperature alert OFF or ON.
Outdoor Temperature Search
•Hold the SEARCH button to search for the
outdoor sensor.
•Press the TX button on the sensor.
•The outdoor reception icon will flash while searching.
Reset Button
•If the clock display appears distorted or is not responding to
buttons, use a pen or paperclip to press RESET one time.
•This will reset the clock to default settings.
WWVB Radio-controlled Time
•Hold the - °C/°F button to search for the WWVB time signal.
•WWVB Icon will flash when searching.
For information about WWVB visit:
www.nist.gov/pml/div688/grp40/wwvb.cfm
ATOMIC SIGNAL SEARCH:
The atomic clock will search for 1 hour between midnight and 6am until
the WWVB time signal is received. After reception, the atomic clock will
only search for the atomic signal after midnight.
Position Outdoor Sensor
•Mount the outdoor sensor on a north-facing wall or in any well
shaded area. Under an eave or deck rail is preferred.
ALERT + 12/24 - °C/°F
High
Alert
Icon
Low
Alert
Icon
SEARCH
Outdoor
Reception
Icon
WWVB
Atomic Icon
- °C/°F

Model: 513-1311OT www.lacrossetechnology.com/support Page | 5
•The maximum transmitting range to the wireless thermometer is
over 330 feet (100 meters) in open air, not including walls.
Specifications
Temperature Range:
Indoor:
Outdoor:
+32°F to +122°F (0 ºC to 50 ºC)
-4°F to 122°F (-20°C to 50°C)
Power Requirements:
Atomic Clock:
KW5012FSK Sensor:
3-C, IEC, LR14 batteries (not included)
2-AA, IEC, LR6 batteries (not included)
Battery Life:
Atomic Clock &
KW5012FSK Sensor:
Battery life is over 12 months when using
reputable battery brands
Dimensions:
Atomic clock:
KW5012FSK Sensor
16.14” W x 1.69” D x 10.63” H
(410 x 43 x 270 mm)
4” H x 2.44” W x .88” D
(101.6 x 61.98 x 22.35mm)
Care and Maintenance
•Do not mix old and new batteries
•Do not mix Alkaline, Standard, Lithium or Rechargeable
Batteries
•Do not expose to extreme temperature, vibration or shock.
•Clean with a soft damp cloth. Do not use solvents.
•The product is not a toy. Keep it out of reach of children.
•The product is not to be used for medical purpose or for public
information. It is intended for home use only.
•The specifications of this product may change without prior notice.
•Improper use or unauthorized opening of housing voids warranty.
Warranty and Support Information
La Crosse Technology, Ltd. provides a 1-year limited time warranty (from
date of purchase) on this product relating to manufacturing defects in
materials & workmanship.
View full warranty details online at:
www.lacrossetechnology.com/warranty_info.pdf

Model: 513-1311OT www.lacrossetechnology.com/support Page | 6
For warranty work, technical support or other information contact:
La Crosse Technology, Ltd
2830 26th Street S.
La Crosse, WI 54601
Contact Support:
1-608-782-1610
Product Registration:
www.lacrossetechnology.com/support/register
Online Product Support:
www.lacrossetechnology.com/513-1311ot
Protected under U.S. Patents:
5,978,738 / 6,076,044 / 6,597,99
FCC Statement
This Device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) the device must accept any interference received,
including interference that may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY
RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER AUTHORITY TO OPERATE THE
EQUIPMENT
All rights reserved. This handbook must not be reproduced in any form,
even in excerpts, or duplicated or processed using electronic,
mechanical or chemical procedures without written permission of the
publisher.
This handbook may contain mistakes and printing errors. The information
in this handbook is regularly checked and corrections made in the next
issue. We accept no liability for technical mistakes or printing errors, or
their consequences.
Scan for full
manual