La Crosse 519-1416 User manual

Model: 519-1416 www.lacrossetechnology.com/support Page | 1
Model: 519-1416
Quick Setup Guide
MULTIFUNCTIONAL ATOMIC CLOCK
STOPWATCH | TIMER | EVENT COUNTDOWN
1
2
3
4
5
6
7
Battery
Compartment
3 “AA”
Battery Cover
BACK
VIEW
FOLDABLE
STAND
FRONT
VIEW
Buttons

Model: 519-1416 www.lacrossetechnology.com/support Page | 2
Alarm
Bell Icon
GET STARTED
Step 1: Insert 3 new AA Alkaline batteries (not included) into the clock.
Observe the correct polarity.
Restart: If the time (12:00) is not displayed after 30 seconds, first, check the battery
polarity. Second, remove batteries from the clock for 15 minutes. Return to Step 1 above.
SET TIME
1. Hold button 7 (MODE)to enter time set mode.
2. Press button 2 or 6 (DOWN or UP) to adjust values.
3. Press button 7 (MODE) to confirm adjustments and move to the next item.
TIME SET ORDER:
1. WWVB time signal (On/Off)
2. Time Zone - 7 time zones
3. DST (Daylight Saving Time On/Off)
4. 12/24 hour time format
5. Hour
6. Minutes
7. Seconds
8. Month
9. Date
10. Year
Note: When you select WWVB OFF, Time Zone and DST disappear from the time setting
order.
Press button 7 (MODE)to exit, or wait 30 seconds without pressing buttons to
return to the normal time display.
TIME ALARM (“AL” will show in place of seconds)
1. Hold button 3 (ALARM) to enter alarm time set mode.
2. Press button 2 or 6 (DOWN or UP) to adjust ALARM TIME.
3. Press button 3 (ALARM) to confirm adjustments and move to the next item.
ALARM TIME SETTING ORDER:Hours, Minutes
Activate/Deactivate TimeAlarm
•Press button 3 (ALARM) once to view alarm time.
•Press button 3 (ALARM) again to activate the alarm.
Once activated the bell icon appears.
•Press button 3 (ALARM) again to deactivate the alarm.
The bell icon will disappear.
Snooze (silences alarm temporarily)
•When alarm sounds, press button 4(SNOOZE) to silence the alarm for 10
minutes. The snooze icon Zz and the alarm icon will flash.
•In snooze mode, press any button to stop alarm for one day.
Note: The alarm is crescendo sound. The alarm will sound for 2 minutes and then shuts off
completely.

Model: 519-1416 www.lacrossetechnology.com/support Page | 3
STOPWATCH (Count up, tracks duration of events)
1. Press button 7 (MODE) to switch to Timer Mode.
2. Press button 1 (START/STOP) to begin count up.
3. Hold button 1 (START/STOP) to reset and start again from zero.
Note: This clock has count up capacity of 9 years, 364 days, 23:59:59.
•At 24 hours, a DAY indicator will show
•At 365 days a YEAR indicator will show
COUNTDOWN TIMER (cooking, exercising, preset times)
Note: The timers will continue to run if you change modes, allowing full clock and time
alarm function.
The countdown timer is programmable up to 23 hours, 59 minutes and 59
seconds.
Set Timer:
1. Press button 7 (MODE) to switch to timer mode.
2. Hold button 7 (MODE) to enter timer set mode.
3. Press button 2 or 6 (DOWN or UP) to adjust countdown timer.
4. Press button 7 (MODE) to confirm adjustments and move to the next item.
TIMER SETTING ORDER: Seconds, Minutes, Hours
1. Press button 1 (START/STOP) to start or stop the timer.
2. Hold button 1 (START/STOP) to clear the timer numbers.
Timer Alarm
•When the timer reaches zero, the alarm will sound for 20 seconds.
•The timer icon will flash.
•The clock will start counting up and display the +icon.
•Press any button to stop the alarm.
The Timer icon with arrow pointing up will be displayed,
Once the timer start the arrow will flash
The Timer icon with arrow pointing down will be displayed,
Once the timer start the arrow will flash

Model: 519-1416 www.lacrossetechnology.com/support Page | 4
Countdown Timer Memory
•In timer mode, press button 5 (MEM) to select from 5 preset values from 5
minutes to 30 minutes: (MEM1: 5 min, MEM 2: 10min, MEM 3: 15 min,
MEM 4: 20 min, MEM 5: 30 min).
•Press button 1 (START/STOP) to start or stop the timer.
Change any preset memory value:
1. Press button 5 (MEM) to select timer memory.
2. Hold button 7 (MODE) to enter timer set mode.
3. Press button 2 or 6 (DOWN or UP) to adjust countdown timer.
4. Press button 7 (MODE) to confirm adjustments and move to the next item.
TIMER SETTING ORDER: Seconds, Minutes, Hours
EVENT TIMER (holiday/appointment countdown, up to 5 events)
The event timer is programmable up to 9 years, 364 days, 23 hours 59 minutes
and 59 seconds.
1. Press button 7 (MODE) to switch to event timer.
2. Hold button 7 (MODE) to enter event timer set mode.
3. Press button 2 or 6 (DOWN or UP) to adjust event timer.
4. Press button 7 (MODE) to confirm adjustments and move to the next item.
EVENT TIMER SETTING ORDER: Month, Date, Year, Hours, Minutes, Seconds
•Note: The date information (month date, year) will show next to the event ico
1. Press button 1 (START/STOP) to start or stop the event timer.
2. Hold button 1 (START/STOP) to clear the event timer.
Event Alarm
•When the event timer reaches zero, the alarm will sound for 20 seconds.
•The event icon will flash.
•The clock will start counting up and display the +icon.
•Press any button to stop the alarm.
Memory
Number

Model: 519-1416 www.lacrossetechnology.com/support Page | 5
Event Timer Memory
The event timer does not have preset values. When you set events, they will
store into memory for easy recall with button 6 (MEM).
The first event will store in MEM 1. The next events will store MEM 2, MEM 3,
MEM 4, and MEM 5. Then the next time an event is saved it will replace MEM 1
and start the sequence again.
MEMand a number (MEM 1) will display above the event timer, when you use a
preset event timer memory.
Note: Multiple timers (event, stopwatch or countdown) can run at the same time.
The timers will continue to run in the background, when the clock is displayed.
MANUAL WWVB RADIO-CONTROLLED TIME SEARCH
•Press button 6 (+ UP) button to start or stop a manual signal search.
•WWVB Icon will flash
For information about WWVB, visit:
www.nist.gov/pml/div688/grp40/wwvb.cfm
LOW BATTERY ICON
•Low battery icon indicates low battery for the clock.
•If the icon is displayed replace batteries.
SPECIFICATIONS
Operating Temperature:32°F to 122°F (0°C to 50°C)
Power: 3-AA, IEC, LR6 batteries (not included)
Battery Life: Battery life is over 24 months when using
reputable battery brands.
Dimensions: 11.81”L x 6.49”H
(29.97cm x 16.51cm)
CARE AND MAINTENANCE
•Do not mix old and new batteries
•Do not mix Alkaline, Standard, Lithium or Rechargeable Batteries
•Do not expose to extreme temperature, vibration or shock.
•Clean with a soft damp cloth. Do not use solvents.
•The product is not a toy. Keep it out of reach of children.
•The product is not to be used for medical purpose or for public information. It
is intended for home use only.
•The specs of this product may change without prior notice.
•Improper use or unauthorized opening of housing voids warranty.
Low Battery
Icon
WWVB
Icon

Model: 519-1416 www.lacrossetechnology.com/support Page | 6
WARRANTY AND SUPPORT INFORMATION
La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of
purchase) on this product relating to manufacturing defects in materials &
workmanship.
View full warranty details online at:
www.lacrossetechnology.com/warranty_info.pdf
For warranty work, technical support or other information contact:
La Crosse Technology, Ltd
2817 Losey Blvd. S.
La Crosse, WI 54601
Contact Support:
1-608-782-1610
Product Registration:
www.lacrossetechnology.com/support/register
Online Product Support:
www.lacrossetechnology.com/519-1416
Protected under U.S. Patents: 5,978,738, 6,076,044, 6,597,990
FCC STATEMENT
This Device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) the device must accept any interference received, including interference that
may cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR
TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY
TO OPERATE THE EQUIPMENT
All rights reserved. This handbook must not be reproduced in any form, even in
excerpts, or duplicated or processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors. The information in this
handbook is regularly checked and corrections made in the next issue. We
accept no liability for technical mistakes or printing errors, or their consequences.
Scan for full
manual online