Lacertosus LM-SA2 User manual

- 1 -
Lat Machine Stand Alone 2.0
LM-SA2

- 2 -
EXPLODED DRAWING

- 3 -
PARTS LIST
NO. DESCRIPTION Q'TY NO.
DESCRIPTION
Q'TY
1 Rear Bass Frame 1 30
Leg Cushion
2
2 Top Frame 1 31
Rubber Pedal
2
3 Base Frame 1 32
Rubber Bumper
2
4 Upright Frame 1 33
Big Ru
bber Bumper 2
5 Pedal Frame 1 34
Rubber Feet
2
6 Front Base Tubing 2 35
Rubber Cushion
2
7 Weight Plate Frame 1 36
End Cap 50*50*75
5
8 Foam Frame 1 37
Plug Cap
3
9 Weight Stack Frame 2 38
End Cap
Φ48*2.5 2
10 Hook 3 39
Carabineer Φ8*80
5
11 Knob 1 40
Flat WasherΦ11*Φ20*2
16
12 Magnetic PinΦ10*93 1 41
Flat WasherΦ10.5*Φ30*2.5
2
13 Top Connect Plate 2 42
Flat WasherΦ13.5*Φ24*2.5
30
14 Metal Cover 2 43
Nut M10
7
15 Long Pulley Bracket 2 44
Nut
M12 17
16 Side Connecting Plate 2 45
Hex Bolt M10*25
8
17 Guide Rod 2 46
Hex Bolt M10*45
5
18 Top Weight Stack 1 47
Hex Bolt M10*90
2
19 Weight Stack 20 48
Hex Bolt M12*70
1
20 Selectorized Rod 1 49
Hex Bolt M12*100
4
21 Foam Plate 2 50
Hex Bolt M12
*105 8
22 PulleyΦ95*Φ10.2*24 7 51
Round Head Hex Bolt M5*10
1
23 Pulley Bushing 4 52
Round Head Hex Bolt M10*20
2
24 ChainΦ5*230 2 53
Round Head Hex Bolt M10*50
1
25 High Pulley Handle 1 54
Cross Recess Pan Head Screw M5*10
12
26 Lower Handle Bar 1 55
Pan Head Hex Bol
t M6*15 6
27 Top Cable Assembly 1 56
Pan Head Hex Bolt M8*25
2
28 Lower Cable Assembly 1 57
Pan Head Hex Bolt M12*95
4
29 Seat Cushion 1 58
Hex Bolt M8*12
8

- 4 -
ASSEMBLY
STEP 1
Install Guide Rod (17) to Rear Bass Frame (1) using 2 pieces Hex Bolt M10*25 (45) as drawing.
STEP 2
Assemble Rear Bass Frame (1), Base Frame(3) and Front Base Tubing(6) using 4 pieces Hex Bolt
M12*100(49),8 pieces Flat WasherΦ13.5*Φ24*2.5(12) and 4 pieces Nut M12(44) as drawing.

- 5 -
STEP 3
Put Weight Stack Frame(9), Big Rubber Bumper(33), Weight Stack(19), Top Weight Stack(18) and Weight
Plate Frame(7) on Guide Rod (17) in turn, then fixed Weight Plate Frame(7) to Top Weight Stack(18) using 2
pieces Flat WasherΦ11*Φ20*2(40) and 2 pieces Round Head Hex Bolt M10*20(52) as drawing.
STEP 4
Assemble Top Frame (2), Base Frame (3), Upright Frame (4), Top Connect Plate (13), Side
Connecting Plate (16) and Guide Rod (17) using 2 pieces Flat WasherΦ10.5*Φ30*2.5(41), 16
pieces Flat WasherΦ13.5*Φ24*2.5(42),8 pieces Nut M12(44),2 pieces Hex Bolt M10*25(45) and 8
pieces Hex Bolt M12*105(50) as drawing.

- 6 -
STEP 5
Take Top Cable Assembly (27) and Lower Cable Assembly (28) through Long Pulley Bracket (15);
Bolted the perforated bolt on the Top Cable Assembly (27) to Selectorized Rod (20), and connect
the other end of Top Cable Assembly (27) in turn with the Carabineer Φ8*80(39), ChainΦ5*230(24) ,
Carabineer Φ8*80(39) and High Pulley Handle(25) as drawing; One end of Lower Cable Assembly
(28) connect the Carabineer Φ8*80(39), ChainΦ5*230(24) , Carabineer Φ8*80(39) and Rear Bass
Frame (1) as drawing,the other end of Lower Cable Assembly (28) connect Carabineer
Φ8*80(39).Please remove ChainΦ5*230(24) and Carabineer Φ8*80(39) from High Pulley
Handle(25),then connect the Lower Cable Assembly (28) and Lower Handle Bar(26).

- 7 -
STEP 6
Install Pedal Frame (5) to the required position on the Front Base Tubing (6) using Flat
WasherΦ13.5*Φ24*2.5(42), Nut M12 (44) and Pan Head Hex Bolt M12*95(57);Install Hook (10) to
the correct postion on the Top Frame(2) and Upright Frame(4) as drawing.
STEP 7
Install Foam Frame Assembly (8) to Upright Frame (4) using Flat WasherΦ13.5*Φ24*2.5(42), Nut
M12 (44) and Hex Bolt M12*70(48), then adjust the required position in Knob (11);Install Seat
Cushion(29) to Base Frame(3) using Flat WasherΦ11*Φ20*2(40) and Hex Bolt M10*25(45) as
drawing.
Please tighten all the bolts and nuts.