Lamination Depot TruLam TL-320E User manual

TRULAM is a trusted brand of
WWW.LAMINATIONDEPOT.COM
Volume 719
OPERATION GUIDE
TL-320E
12.5 INCH POUCH LAMINATOR
contact us:
800.925.0054
[email protected]
WARRANTY
PRO TIPS & MAINTENANCE
• Use the reverse button if document jams/wraps around rollers. Always insert document
with sealed edge first. DO NOT attempt to access jam until machine is cooled down and
unplugged.
• Run a test document at the beginning of each new session to ensure proper lamination.
• Required temperature may vary depending on adhesive quality and surrounding
temperature of your room/office.
• If pouch appears cloudy after lamination then the temperature is set too low. Slightly
increase the temperature and insert new pouch. Repeat until the pouch is clear.
• If pouch appears crinkled or warped then the temperature is set too high. Slightly
decrease the temperature and insert pouch. Repeat until the pouch is flat and clear.
• Remove glue residue from rollers by turning on machine and setting to default tempera-
ture of 212ºF. Prepare a sheet of letter-sized paper and fold in half. Insert the folded edge
into throat of machine. Repeat until paper has removed all residue.
• Clean the exterior of the machine with a soft cloth. Always ensure machine is turned off,
unplugged, and cooled down before wiping down.
• Do not allow children to operate this machine.
• Do not attempt to laminate more than indicated capacity, as it may jam or damage the
machine.
• Keep the machine away from moisture.
• To prevent injury and/or damage to the machine, ensure machine is on a flat, stable
surface before using.
Lamination Depot warrants the TL-320E against any defects for 12 months from the date
of original purchase. Warranty does not cover normal wear and tear, nor damage caused
by operator error or misuse. Should any defect appear within 12 month warranty from date
of purchase we will gladly repair or replace the machine. To start a warranty claim within
12 months from date of purchase please contact our customer service team by calling
[phone] or by email [email protected].
To process your warranty claim, the machine must be returned in its complete original
packaging to avoid incidental damages in transit by the carrier of your choice. Lamination
Depot does not cover shipping costs for claims nor is responsible for any damages
caused by the carrier.
Upon evaluation of the machine and determination of the actual defect, the machine will
be restored to its original factory specifications and will be shipped back to you free of
charge using the carrier of our choice. If the machine cannot be restored, a replacement
will be provided.
This warranty covers all defects incurred in the normal use of the equipment except in the
following cases:
• Damage to the equipment due to improper operation, abuse, mishandling or failure to
follow the operating instructions.
• Removal or alteration of the serial number.
• Service or modification done by anyone other than a certified technician authorized by
Lamination Depot.
This warranty is valid only within the United States or its provinces and territories.

SPECIFICATIONS
FEATURES OPERATION GUIDE | 6 EASY STEPS
• Model: TL-320E
• Use: Home & Office
• Seals up to: 3 mil - 10 mil in pouch thickness
• Speed: 25.6” per minute
• Width: 12.5”
• 4 Rollers
• Reverse switch: Yes
• Auto shut-off: No
• Carrier required: No
• Unit weight: 17.6 lbs
• Machine Dimensions: 19.7” W x 8.3” D x 3.9” H
• Warranty: 1 year
• On/Off Switch
• Power Button
• Ready Light
• Temperature Display
• Reverse Button
• Throat
• Temperature Selection
6. To turn off, reduce temperature to
190ºF and wait approx. 15 min. Press
the Power Button twice then switch off
the Power Switch in the back.
5. Allow rollers to automatically guide
document to back of machine to seal.
Gently remove document and lay on flat
surface to cool.
4. Ensure document is centered in your
pouch with even edges. Carefully insert
the sealed end into the throat located
on front of machine.
3. Use the guide located on the front of
the machine to select proper tempera-
ture and speed. Wait for ready light to
turn solid green & machine beeps.
2. Turn on the Power Switch located on
the back of the machine.
1. Use the female connector of the
power cord to plug into the back of the
machine. Use the male connector to
plug into an appropriate power source.