Lamona LAM2504 Guide

Instructions and Installation
LAM2504
Black Curved Glass
Chimney Extractor
www.howdens.com/appliance-registration

See back page for product serial number

www.howdens.com
Page _ 2
LAMONA Appliances
Dear Customer,
Congratulations on your choice of a LAMONA domestic appliance.
The user manual will help you use your product quickly and safely.
• Please read this user manual before installing and using the product.
• Always follow the safety instructions.
• Keep this user manual within easy reach for future reference.
• Please read any other documents supplied with the product.
Explanation of symbols
Throughout this user manual the following symbols are used:
Important information or useful tips about usage.
Warning for possible hazards to health and property.
Warning possibility of electric shock.
This appliance is marked according to the European Directive 2012/19/EU on Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly you will help prevent potential negative
consequences for the environment and human health. The symbol on this product indicates that this product
may not be treated as household waste. Instead it should be handed over to the applicable collection point for
recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local
environmental regulations for waste disposal. For more detailed information please contact your local council
household waste site.

Exclusive to Howdens Joinery.co Page _ 3
User Manual LAM2504
Index
Before Using The Extractor 04
Safety 04
General 04
Safety for Children 05
Safety When Working With Electricity 05
General Information and Operation 06
Extractor Layout 06
Control Panel Layout 06
Care and maintenance 07
General Cleaning 07
Grease Filters 07
Carbon Filters 08
Replacing the Lamps 08
Installation 09
Methods of Extraction 09
Extraction Via Ducting 09
Extraction Via Recirculation 09
Parts Identification 10
Hanging Your Extractor 11
Decorative Chimney Fitting 12
Electrical Connections 13
14
Troubleshooting 14
Your Guarantee 15
Technical Specification

www.howdens.com
Page _ 4
LAMONA Appliances
• Make sure that you have removed all packaging, wrappings, stickers and from the Extractor
• It is recommended that you clean the extractor’s surface before using for the time.
Before Using the Extractor
This appliance is for domestic extraction
The manufacturer shall not be liable for any
damage caused by improper use,
installation or handling errors
General
This product is not intended to be used by
persons with physical, sensory or mental
disorders or unlearned or inexperienced
people (including children) unless they are
supervised by a person who will be
responsible for their safety or who will
instruct them accordingly in the use of the
product.
• Connect the product to an earthed outlet
protected by a fuse of suitable capacity
as stated in the “Technical Specifications”
table. Our company shall not be liable for
any problems arising due to the product not
being earthed in accordance with local
regulations
• Do not operate the product if the power
cable is damaged. Call a qualified service
agent.
• Do not carry out repairs or modifications on
the product. However, you may remedy some
of the problems that do not require any
repairs or modifications.
See “Troubleshooting”, at the rear of this
manual.
• Never wash down the product with excessive
water, as there is a risk of electric shock
• Never use the product when your judgment
or coordination is impaired by the use of
alcohol and/or drugs.
• Product must be disconnected from the
mains during installation, maintenance,
cleaning and repair procedures.
• Repair procedures must always be
performed by qualified service agents.
The manufacturer shall not be held
responsible for damages arising from
procedures carried out by unauthorised
persons, which may also void the
guarantee.
• Keep all ventilation slots clear of
obstructions, as this may cause
premature failure of the appliance
• Do not trap the mains cable and do not
route it over surfaces which may become
hot. The cable insulation my melt and
cause a fire as a result of a short circuit.
• Make sure that the product function
buttons are switched off after every use.
• Product must be installed by a qualified
person in accordance with the
regulations in force otherwise, the
guarantee may become void.
• The hood must be installed in accordance
with the installation instructions and all
measurements followed
If the cooker hood is installed for use
above gas appliance then the provision
for ventilation must be in accordance
with the Gas Safety Codes of Practice
BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the
Gas Safety (Installation & Use)
Regulations, the Building Regulations
issued by the Department of the
Environment, the Building Standards
(Scotland) (Consolidated) Regulations
issused by the Scottish Development
Department
Safety
purposes only. It must not be used for other
purposes. Commercial use will void the
guarantee.

Exclusive to Howdens Joinery.co Page _ 5
Do not set your cooker hood less
than 700mm above your cooker
•When installed between adjoining
wall cabinets, the cabinets must not
overhang the hob.
• The edges of the cooker hood may
be sharp - be mindful of this as you
handle your appliance, especially
during installation and cleaning
•If the room where the cooker hood is
to be used contains a fuel burning
appliance such as a central heating
boiler then its flue must be of the
sealed or balanced flue type.
• If other types of flue or appliances are
fitted, ensure that there is an
adequate supply of air in the room
• When the hood is being used in
extraction mode, ensure that the
ducting is fire retardant and that
there are no bends greater than 90
degrees as this will reduce the
effiency of the hood
•Ensure the ducting for the extractor
mode has the same diameter as the
outlet hole all the way through.
r
Fire Safety
When installing the hood, ensure that
the following recommended distances
are observed between the heighest
point on the hob top (including the
burners) and the bottom of the
cooker hood:
mm007:srekooCcirtcelE
mm007:srekooCsaG
mm008:srekooCliO/laoC
• Never flambé cook under this cooker
hood.
• Dirty cooking oil is an even greater fire
risk
• Do not install above a cooker with a
high level grill.
Safety for Children
•Electrical products can be dangerous
to children. Keep children away from
the product when it is operating and do
not allow them toplay with or near the
product.
• The packaging materials will be
dangerous for children. Keep the
packaging materials away from children.
Please dispose of all parts of the
packaging according to the
environmental standards
Safety When Working with
Electricity
• In case of any damage, switch off the
product and disconnect it from the
mains. To do this, turn off the fuse at
the fuse box.
• Make sure that the fuse rating is
compatible with the product.
User manual LAM2504
Do not clean behind the
grease filter!
Always put lids on pans and ensure
that pans are always on hobs when
burners are lit.
•
Remember that when in extraction
mode, your cooker hood is removing
air from your room. Ensure that
proper ventilation measures are
being observed.
•

Exclusive to Howdens Joinery.co Page _ 6
User manual LAM2504
5.
6.
2.
7.
8.
1.
3.
4.
1. Upper Chimney Section
2. Recirculation Vent
3. Lower Chimney Section
4. Fan and Light Controls
5. Extractor Body
6. Grease Filters
7. Light
8. Glass Canopy
General Information & Operation
0
1. 2. 3. 4. 5.
1. 2. 3. 4. 5.
1. 2. 3. 4. 5.
Extractor layout
Control Panel Layout
1. Extractor Power Off
2. Extractor Power Level 1
3. Extractor Power Level 2
4. Extractor Power Level 3
5. Extractor Light On/Off

www.howdens.com
Page _ 7
LAMONA Appliances
Before cleaning or attempting any type of maintenance, always make sure that the electricity
supply is disconnected.
The manufacturer declines all liability in cases where the instructions for the appropriate installation,
maintenance and use of the extractor hood are not observed.
If the power cable is cut or damaged in any way, disconnect the extractor from the electricity supply and call
the service number on the rear cover of this booklet or a suitably repairer.
General Cleaning
Care and Maintenance
The grease filter is of a metallic material and should
be washed using a neutral detergent.
1 Push latch
2 Lower filter to remove.
2
1
Wipe the external surfaces of the appliance regularly using a damp cloth and mild detergent. NEVER use
abrasive cleaners
Do not use a steam cleaner to clean the hood; electrical components could be damaged or short-circuit as
a result
The Grease Filters
Clean the filter every month; an excessive build-up of grease can become a fire hazard. The filter collects
grease, smoke and dust.... so the filter directly affects the efficiency of the cooker hood. If it’s not cleaned,
the grease residue (potentially flammable) will saturate on the filter.
Remove the filter as shown in the Installation section. Clean it with a soft nylon brush in a mild solution of
warm water and a small amount of washing up liquid. Washing up liquid alone should not be used. After
cleaning, allow the filter to drain and the dry thoroughly.
The grease filter may also be dishwasher cleaned; using a 60 or 65 degree C programme, with the filter
upright (short sides upright) in the lower basket.. Please be aware some dishwasher cleaning agents can be
permanently discolour the filter, though this will not affect its performance.

Exclusive to Howdens Joinery.co Page _ 8
User Manual LAM2504
The Carbon Filters
Carbon have a limited life. We advise you to change them when there is a noticeable drop in
performance. The intervals between changing the will depend entirely upon the amount of cooking you
do, but on average they will last about 3 - 6 months. Please quote the part reference number HJA2906
(pack of 2) when re-ordering.
• To gain access to the carbon filters, first of all remove the grease filters as above.
• Remove the old filters and install new charcoal filters by turning them gently
Replacing the Lamps
The extractor hood is with x2 LED lamp units that must only be replaced by a suitably qualied person .
The lights are powered by an electronic driver device and neither part is repairable .We recommend that you
call the Sevice Line if light replacement is needed.
Lamp replacement is not covered by your guarantee
The lamps on this appliance should only be used during operation of the cooker hood. They should not be
left on permanently and used as a main lighting source. The extractor is for domestic use only.
2
1
• Make sure the filter is securely locked. Otherwise, it could loosen and cause damage to the unit
• When the activated carbon filters are attached, the suction power will be lowered.
• The charcoal cannot be washed or recycled.

www.howdens.com
Page _ 9
LAMONA Appliances
Methods of Extraction
The very best method of clearing the kitchen of unwanted odours is by connecting the appliance to an
exhaust duct and venting to the outside atmosphere via the ceiling or an exterior wall. (Suitable ducting kits
may be purchased from the depot where you bought the extractor.) You do not need charcoal when
using the external ducting mode.
Filtered air
recirculated
Ducting kit (APL2805/6/7)
Supplied Separately
Vent through external
wall or ceiling
Fig 1.
Ducting mode
(No charcoal required)
Fig 2.
Recirculation mode
(Charcoal HJA2906 required)
Extraction Via Ducting
Never use the hood in areas where devices with
exhaust pipes connected to the outside are
already operating unless perfect ventilation can be
guaranteed.
• Connect the external ducting kit to the outlet
of the extractor.
Charcoal are not required if the extractor
is to be ducted out.
Extraction Via Recirculation
For extraction via recirculation, attach 2 charcoal
to the sides of the motor inside the hood.
These can be ordered separately quoting part
reference HJA2906
switched off.
• Remove the grease
• Align the carbon over the pins located
on either side of the fan motor.
• Turn the carbon gently, until you feel them
click into position.
• Replace the grease before the power
supply it turned back on.
Installation We recommend you turn the extractor on
5-10 minutes before cooking for maximum
efficiency of operation.

Exclusive to Howdens Joinery.co Page _ 10
User manual LAM2504
PARTS IDENTIFICATION
On opening your box you will the extractor body, a two-piece telescopic decorative chimney, a bag of
wall and screws, two brackets, a ducting connector and reducer.
1. Main Extractor Body
2. Lower Chimney
3. Upper Chimney
4. Upper Fixing Bracket
5. Lower Chimney Bracket
6. Outlet Reducer
7. Rawl Plug
8. 30mm Screw
9. 10mm Screw
1. 2. 3.
4.
5.
6.
7.
8.
9.

www.howdens.com
Page _ 11
LAMONA Appliances
Hanging Your Extractor
This instruction must be strictly adhered to. Failure to comply could result in overheating and
serious damage to your appliance. It is recommended that the installation is carried out by two people.
Before drilling or chiselling the ceiling or wall, check for pipes and power cables.
• If ducting externally ensure the ducting tube is kept as short as possible and with the minimum
of bends to permit the smoothest (Maximum length 3 metres.). Ducted air must not be
discharged into a which is used for exhausting fumes from appliances supplied with energy other
than electricity. (E.g. gas boilers)
• Ensure the requirements of the local authorities are adhered to concerning the discharge of exhaust
air.
• Ensure adequate room ventilation is provided when the extractor is used in the same room as
appliances supplied with energy other than electricity.
• Never duct into a hot air such as a central heating duct
320mm
700 mm Minimum distance to worktop
750 mm Recommended distance to worktop
**
**
**
**
** **
Worktop
Wall
73mm
(**) Please use rawl plugs and screws appropriate
to the type of wall (not supplied)
700 mm Minimum distance to worktop
750 mm Recommended distance to worktop
40 mm
260 mm
219 mm Please use rawl plugs and screws
appropriate to the type of wall
Wall
=
=
2
1
2
3
1. Remove the grease before trying to install.
2. The recommended height for the hood is 750mm above the worktop. This can be reduced to a
minimum of 700mm if required.
3. Mark and drill the holes required to mount the extractor body.
4. The principal securing points are the 2 key holes; fix this first.is
5. With the help of an assistant, hang the extractor body on the screws level and secure in position
through the lower two .
254 mm =
=

Exclusive to Howdens Joinery.co Page _ 12
User Manual LAM2504
Decorative Chimney Fitting
1. Connect the extractor to the electricity supply (see electrical connections page). We recommend an
isolation switch that is accessible after installation.
2. The outlet reducer maybe required depending on your ducting kit (supplied separately).
3. Fit the appropriate ducting kit if venting externally.
4. Rest the chimney sections on the main extractor body and extend the upper section to the ceiling
5. Use the extended chimney sections to mark-up the appropriate position of the bracket
6. Remove the chimney sections, drill and secure upper fixing bracket with appropriate fixings.
7. Resit the chimney sections on to the extractor body, hooking the lower section on to brasket and
secure to the wall using the screws provided
3.
2.
1.
4.
Note: Remember not to fix the screw too
tightly, so that later height adjustment can
be done more easily.

www.howdens.com
Page _ 13
LAMONA Appliances
Electrical Connections
IMPORTANT: Ensure that the electricity supply is switched off before connecting.
Your appliance must be connected to wiring via the use of a double pole switched fused spur outlet
with at least 3mm contact separation, The isolation switch must be accessible after installation. (See
technical data for fuse rating).
The terminology DOUBLE POLE -/+ means that both the live and neutral supplies are switched and
disconnected at the same time.
The terminations labelled SUPPLY are the connections for the internal house wiring and the terminations
labelled LOAD are for connection to the appliance.
IMPORTANT: The wires in the mains lead are coloured in accordance with the following code:-
Blue.....................Neutral
Brown..................Live
Green/ Yellow.....Earth
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured
markings identifying the terminals in your spur box, proceed as follows;
The wire which is coloured blue must be connected to the terminal which is marked with the letter
‘N’ or coloured BLACK. The wire which is coloured brown must be connected to the terminal which
is marked with the letter ‘L’ or coloured RED. The wire which is coloured Green and Yellow must be
connected to the terminal which is marked with the letter ‘E’ or Symbol
Fig 3. Fig 4.
N
L
L
N
LOAD
SUPPLY
LOAD
SUPPLY
DP
13A 250V~
FUSE ON
Blue.
(Neutral)
Brown.
(Live)

Exclusive to Howdens Joinery.co Page _ 14
User manual LAM25044
TROUBLESHOOTING GUIDE
Symptoms Possible Cause Solutions
Lamps fail to operate? • A replacement lamp is probably
necessary, but check that the
lamp is correctly into its holder.
(Remember that the lamps are not
covered by the guarantee.)
Disconnect the mains electricity supply before adjusting
or replacing the lamps.
The extractor lamps may become hot; therefore ensure
the bulb has cooled before replacing.
• Power is cut. Check if there is power. Check the fuses in the fuse box. If
necessary, replace or reset the fuses.
The motor is on, but fan does
as usual?
• Clogged can reduce the
product’s Check the grease
and charcoal (if also
ensure any venting is not obstructed?
Clean the grease with warm water and mild
detergent, and/or replace any charcoal
The extractor works normaly
but smells linger?
• Clogged can reduce the
product’s and may cause
unwanted smells.
Clean the grease with warm water and mild
detergent, and/or replace any charcoal
Product does not operate? • The mains fuse maybe defective or
has tripped
Check fuses in the fuse box. If necessary, replace or
reset them.
• Product is not connected properly. Check all power connections.
If you cannot eliminate the problem after following the instructions in this section, consult your
depot or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.
Troubleshooting
TECHNICAL INFORMATION
General
Total power consumption 101 W
Fuse 3 A
Voltage /Frequency 220-240 V ~ 50 Hz
Cable type / section 0.75mm², 3 core or equivalent
Cable length max. 1.5m
Lamps LED

www.howdens.com
Page _ 15
LAMONA Appliances
and serial number on
your machine.
Remove filters, sticker
in the cavity
Product Guarantee Details (UK Only)
Your appliance has the benefit of a comprehensive manufacturer’s guarantee
which covers the cost of breakdown repairs. (Details of which are shown on your
Proof of purchase Document).
• Any claim during the period of the guarantee MUST BE ACCOMPANIED BY THE PROOF OF
PURCHASE.
• The product must be correctly installed and operated in accordance with the manufacturer’s
instructions and used for normal domestic purposes.
• This guarantee does not cover accidental damage, misuse or alterations which are likely to affect
the product.
• The guarantee is invalid if the product is tampered with, or repaired by any unauthorised person.
(The guarantee in no way affects your statutory or legal right)
What to do if you need to report a problem.
Please ensure you have ready:
• The product’s model and serial numbers.
• Howdens Proof of Purchase Document.
• Your full contact details.
Call the Depot number on your Proof of Purchase
Document supplied with the product / kitchen.
or
Call the LAMONA Service Line on 0344 460 0006
*Product installed within a domestic kitchen or a non-domestic kitchen where 8 or fewer people
are using the appliance.

Exclusive to Howdens Joinery.co Page _ 15
User manual LAM2504
LAM2504
61.5 kWh/a
1.8
6.60%
100.4
283.8 m/h
77 Pa
445.2 m/h
92.5 W
1.0 W
64 lux
-
0 W
56 dB
In order to reduce the environmental impact (e.g. energy use) of the cooking process,
please be sure that your product is installed according to the user manual. Ensure
adequate ventilation and keep any duct work as short and as direct as possible.
We suggest switching the motor off within 10 minutes after finishing cooking.

Product serial number
(Place sticker here)
ISSUE v2 290917