Land Pride OS1548 User manual

1
© Copyright 2005 Printed Manual No. 308-305M
Before You Start
Your Overseeder is exclusively designed for your Land
Pride OS1548 & OS1572. Please read these installation
instructions and your Overseeder Operator’s Manual
thoroughlybeforebeginning.Especiallyreadinformation
relating to safety concerns. Also included in the
Operator’sManualisimportantinformation onoperation,
adjustment, troubleshooting, and maintenance for this
attachment (some manual sections do not apply to all
accessories).
A separate Parts Manual for replacement parts can be
purchased from your nearest Land Pride dealer or
downloaded free of charge from our web site at
www.landpride.com. Have model and serial numbers
handy when placing an order.
Manual Part Numbers:
•Operator’s Manual . . . . . . . . . . . . . . . . . 308-303M
•Parts Manual . . . . . . . . . . . . . . . . . . . . . 308-303P
General Information
These option assembly instructions apply to the Front
Roller Packages listed below:
308-258A OS1548 Front Roller Assembly
308-259A OS1572 Front Roller Assembly
A detailed listing of parts for each accessory kit is
provided on page 3. Use the list that is for your
Overseeder as a checklist to inventory parts received.
Please contact your local Land Pride dealer for any
missing hardware.
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
Tools Required:
•Safety glasses
•Work gloves
•Pencil
•Tape Measure
•Center punch
•Hammer
•Electric drill with 21/32" drill bit
•Extension cord (if required)
•Set of wrenches
•3/8" or 1/2" ratchet wrench set
Further Assistance
Your dealer wants you to be satisfied with your new
seeder. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpser[email protected]
Use with 15 Series 48" & 72" Overseeder
Front Roller Option
Assembly Instructions Manual No. 308-305M
11/09/05

2Manual No. 308-305M 11/09/05
Assembly Instructions
■
Assembly Instructions
Refer to Figure 1:
1. Locate and drill two 21/32" front roller mounting
holes in the location shown.
Refer to Figure 2:
2. Attach floating top link (#1) to overseeder hitch using
spacertube(#2),3/4"x4"bolt(#3),lockwasher(#4),
and hex nut (#5). Tighten nut to the correct torque.
3. Assembly front roller scraper (#25) to mounting
brackets (#22) with 1/2"-13 x 1 1/4" GR5 bolt (#26),
lock washers (#27) and hex nuts (#28). Draw hex
nuts up snug.
4. Bolt mounting brackets (#22), front roller arm (#6),
and front roller (#7) together with two 1/2"-13 x 2"
GR5 bolts (#23), flat washers (#24), spring lock
washers (#9) and hex nuts (#10). Draw nuts up snug.
5. Bolt mounting brackets (#22), front roller arm (#6),
and front roller (#7) together with two 1/2"-13 x 2"
GR5 bolts (#23), flat washers (#27), spring lock
washers (#9) and hex nuts (#10). Draw nuts up snug.
6. Bolt front roller arm (#6), and front roller (#7)
together with two 1/2"-13 x 1 1/2" GR5 bolts (#8),
spring lock washers (#9) and hex nuts (#10). Draw
nuts up snug.
7. Attachfrontrollerassemblytoyouroverseederusing
5/8"-11 x 2" GR5 bolts (#11), lock washers (#12) and
hex nuts (#13).
8. Tighten hex nuts (#10 & #13) to the correct torque.
9. Adjust front roller scraper (#25) with a slight gap
between scraper and front roller arm (#6). Hold
scraper in this position and tighten hex nuts (#28) to
the correct torque.
10. Use 1/2" x 2 1/2" x 3 1/2" long U-bolts (#15), lock
washers (#16), and hex nuts (#17) to attach
turnbuckle mounts (#14) to the Overseeder frame.
Refer to Figure 2 & Figure 3:
11. Turnbuckle Mounts (#14) should beSpaced 7 11/16"
from inside edge of end plates as shown.
12. Attach turnbuckles (#18) to mounts (#14) and front
roller arm (#6) with 5/8"-11 x 2 1/2" GR5 bolts (#19),
lock washers (#20) and hex nuts (#21). Tighten nuts
to the correct torque.
13. Refer to Section on Adjustments in your Overseeder
Operator’s Manual308-303M for instructions onhow
to set cutting depth of knives with the front roller.
NOTE: Some parts may already be assembled.
NOTE: 711/16"dimensioninFigure3is the same onboth
48" model and 72" model Overseeders
Hole Locations Typical on Both Ends of Seeder
Figure 1
Front Roller Assembly (Model OS1548 Shown)
Figure 2
Turnbuckle Locations Typical on Both Ends of Seeder
Figure 3
14801
14802
12883

3
11/09/05 Manual No. 308-305M
Assembly Instructions
■
Qty. Part No. Part Description
308-258A 15 Series 48" Overseeder Front Roller Assembly
Your Kit Includes:
1 308-248H FRONT ROLLER WELDMENT OS1572
2 308-252K TURNBUCKLE ASSY 12 3/8-17 7/8
2 308-253H UPPER TURNBUCKLE MOUNT
1 308-256H FRONT ROLLER ARM WELDMENT OS1572
1 308-260H FLOATING TOP LINK
1 308-349H OS1572 FRONT ROLLER SCRAPER RV
1 308-400D FLOATING TOP LINK SPACER TUBE
2 308-405D FRONT ROLLER SCRAPER (MOUNTING ANGLE)
2 802-034C HHCS 1/2-13X1 1/4 GR5
2 802-055C HHCS 5/8-11X2 GR5
4 802-058C HHCS 5/8-11X2 1/2 GR5
1 802-068C HHCS 3/4-10X4 GR5
2 802-091C HHCS 1/2-13X1 1/2 GR5
2 802-128C HHCS 1/2-13X2 GR5
14 803-020C NUT HEX 1/2-13 PLT
6 803-021C NUT HEX 5/8-11 PLT
1 803-027C NUT HEX 3/4-10 PLT
14 804-015C WASHER LOCK SPRING 1/2 PLT
2 804-017C WASHER FLAT 1/2 USS PLT
6 804-022C WASHER LOCK SPRING 5/8 PLT
1 804-023C WASHER LOCK SPRING 3/4 PLT
4 806-010C U-BOLT 1/2-13 X 2 1/2 X 3 1/2
2 822-094C BEARING PILLOW BLOCK 1 3/8BORE
Qty. Part No. Part Description
308-259A 15 Series 72" Overseeder Front Roller Assembly
Your Kit Includes:
1 308-247H FRONT ROLLER WELDMENT OS1548
2 308-252K TURNBUCKLE ASSY 12 3/8-17 7/8
2 308-253H UPPER TURNBUCKLE MOUNT
1 308-255H FRONT ROLLER ARM OS1548
1 308-260H FLOATING TOP LINK
1 308-348H OS1548 FRNT ROLLER SCRAPER RVSBL
1 308-400D SPACER 1 1/4OD X 13/16ID X 2LG
2 308-405D FRONT ROLLER SCRAPER (MOUNTING ANGLE)
2 802-034C HHCS 1/2-13X1 1/4 GR5
2 802-055C HHCS 5/8-11X2 GR5
4 802-058C HHCS 5/8-11X2 1/2 GR5
1 802-068C HHCS 3/4-10X4 GR5
2 802-091C HHCS 1/2-13X1 1/2 GR5
2 802-128C HHCS 1/2-13X2 GR5
14 803-020C NUT HEX 1/2-13 PLT
6 803-021C NUT HEX 5/8-11 PLT
1 803-027C NUT HEX 3/4-10 PLT
14 804-015C WASHER LOCK SPRING 1/2 PLT
2 804-017C WASHER FLAT 1/2 USS PLT
6 804-022C WASHER LOCK SPRING 5/8 PLT
1 804-023C WASHER LOCK SPRING 3/4 PLT
4 806-010C U-BOLT 1/2-13 X 2 1/2 X 3 1/2
2 822-094C BRG PB 1.37ID

Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com