Land Pride PD10 Series User manual

1
© Copyright 2008 Printed
Before You Start
Your Storage Stand is exclusively designed for your
Land Pride PD10, PD15, DP25 & PD35 Post Hole
Diggers. Please read these installation instructions and
your Post Hole Digger Operator’s Manual thoroughly
before beginning. Especially read information relating to
safety concerns. Also included in the Operator’s Manual
is important information on operation, adjustment,
troubleshooting, and maintenance for this attachment
(some manual sections do not apply to all accessories).
A separate Parts Manual for your digger is available free
of charge at www.landpride.com or can be purchased
from your nearest Land Pride dealer. Have the model
and serial number of your Storage Stand handy when
placing an order.
Manual Part Numbers:
•Operator’s Manual . . . . . . . . . . . . . . . . 317-048M
•Parts Manual . . . . . . . . . . . . . . . . . . . . . 317-048P
When you see this symbol, the subsequent
instructions and warnings are serious - follow
them without exception. Your life and the lives of
others depend on it!
!
IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.
General Information
These assembly instructions apply to the following
Storage Stand Accessories listed below:
317-166A PD10Storage Stand
317-142A PD15, PD25, & PD35Storage Stand
Tools required:
•Safety glasses
•Work gloves
•Two 9/16" box end or open end wrenches
•Two 3/4" box end or open end wrenches
Further Assistance
Your dealer wants you to be satisfied with your new
MowerJack. If forany reason youdo not understandany
part of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager. Make sure he has had time to assist you.
2. If you are still not satisfied, seek out the owner or
general manager and explain the problem.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpser[email protected]
For PD10, PD15, PD25 & PD35 Post Hole Diggers
Post Hole Digger Storage Stand
Assembly Instructions
10/06/08
Manual No. 317-189M
PD10 Storage Stand
Figure 1 PD15, 25, and 35 Storage Stand Figure 2
20856 20776

2Post Hole Digger Storage Stand Assembly Instructions Manual No. 317-189M 10/06/08
Land Pride
PD10 Assembly
■
PD10 Assembly
Part No. 317-166A
A detailed listing of parts for this accessory kit is
provided on page 3. Use the list as a checklist to
inventory parts received. Please contact your local
Land Pride dealer for any missing hardware.
Refer to Figure 1 on page 1:
The optional storage stand may be used when PD10
Post Hole Digger is not in operation. It will help
prolong digger’s life by keeping the unit off the
ground where moisture and debris are more likely to
collect causing undue damage to the digger. Also,
the storage stand aids in mounting and dismounting
the Post Hole Digger to and from the tractor.
PD10 Storage Stand Assembly
Refer to Figure 3:
The Storage Stand Assembly consists of an A-frame
storage stand (#7), clamping knobs (#13), cradle
(#5), and a bag of (4) - 5/16” x 3/4” long bolts.
1. Unscrew locknuts (#10) and remove
1/2"-13 x 3 1/2" GR5 hex head bolts (#9). Slide
auger (#1) off of gearbox output shaft.
2. Remove existing hex head cap screws (#8),
lockwashers (#11) and flat washers (#12) from
undersideof gearbox. Remove augerguard (#3).
3. Position cradle (#5) between auger guard (#3)
and gearbox (#14). Make sure cradle pins (#2)
are positioned to the back as shown.
4. Use four new hex head bolts (#8), lock
washers (#11) and flat washers (#12) in
hardware bag to attach cradle (#5) and existing
guard (#3) to gearbox (#14).
5. Reattach auger to gearbox output shaft with
existing auger bolts (#9) and locknuts (#10).
PD10 Storage Stand Operation
Refer to Figure 3:
Loweraugertiptothegroundatthe locationyouplan
to disconnect the Post Hole Digger from the tractor.
Set tractor park brakes, turn tractor engine off, and
remove ignition key before dismounting tractor.
Always chock tractor wheels for an extra measure of
safety if you stop on a gentle slope.
Attach storage stand (#7) to cradle (#5).
1. Make certain guide slots (#6) at end of storage stand are
securely positioned over cradle pins (#2). Secure
storage stand to cradle with clamping knobs (#13).
2. Without starting the tractor, lower boom (#4) to rest yoke
hitch pins securely in support angles on the storage
stand. Some adjustment to the support angles may be
required.
3. Disconnect three-point hitch.
4. Start tractor and drive away being careful not to catch on
the Post Hole Digger and Storage Stand.
PD10 Storage Stand Assembly
Figure 3
NOTE: Do not disconnect Post Hole Digger from a
tractor on a steep slope. Injury to personnel and
equipment may result.
20867

10/06/08 Post Hole Digger Storage Stand Assembly Instructions Manual No. 317-189M 3
Land Pride
Listing of Parts
■
1 317-166A PD10 STAND ASSEMBLY
2 317-148H PD STAND HITCH WELDMENT 2
3 317-164H PD10 STAND CRADLE WELDMENT 1
4 317-165H PD10 STAND WELDMENT 1
5 317-167B PD10 STAND HARDWARE BAG 1
6 802-034C HHCS 1/2-13X1 1/4 GR5 2
7 803-147C NUT HEX NYLOCK 1/2-13 2
8 817-455C KNOB 1/2-13 MALE THD 2 3/8OD 2
9 838-298C DECAL CAUTION DO NOT LEAN ON 2
Kit No. 317-166A PD10 Storage Stand Assembly
Item Part No. Part Description Qty

4Post Hole Digger Storage Stand Assembly Instructions Manual No. 317-189M 10/06/08
Land Pride
PD15, PD25, & PD35 Assembly
■
PD15, PD25, & PD35 Assembly
Part No. 317-142A
A detailed listing of parts for this accessory kit is
provided on page 5. Use the list as a checklist to
inventory parts received. Please contact your local
Land Pride dealer for any missing hardware.
Refer to Figure 2 on page 1:
The optional storage stand may be used when the
PD15, PD25, and PD35 Post Hole Digger is not in
operation. It will help prolong digger’s life by keeping
theunitoff the ground where moistureanddebrisare
more likely to collect causing undue damage to the
digger. Also, the storage stand design aids in
mounting and dismounting the Post Hole Digger to
and from the tractor.
PD15, 25, & 35 Storage Stand
Assembly
Refer to Figure 4:
The Storage Stand Assembly consists of an A-frame
storage stand (#4), clamping knobs (#11), cradle
(#5), and a bag of (4) - 3/8”-16 x 1” long GR5 bolts:
1. Unscrew locknuts (#8) and remove
1/2"-13 x 3 1/2" GR5 hex head bolts (#7). Slide
auger (#13) off of gearbox output shaft.
2. Remove existing hex head cap screws (#6),
lockwashers (#10) and flat washers (#9) from
undersideof gearbox. Remove augerguard (#1).
3. Position cradle (#5) between auger guard (#1)
and gearbox (#12). Make sure cradle pins (#3)
are positioned to the back as shown.
4. Use four new hex head bolts (#6), lock
washers (#10) and flat washers (#9) in hardware
bag to attach cradle (#5) and existing guard (#1)
to gearbox (#12).
5. Reattach auger to gearbox output shaft with
existing auger bolts (#7) and locknuts (#8).
PD15, 25, & 35 Storage Stand
Operation
Refer to Figure 4:
Lowerauger tiptothegroundatthe locationyouplan
to disconnect the Post Hole Digger from the tractor.
Set tractor park brakes, turn tractor engine off, and
remove ignition key before dismounting tractor.
Always chock tractor wheels for an extra measure of
safety if you stop on a gentle slope.
Attach storage stand (#4) to cradle (#5).
1. Make certain guide slots (#2) at end of storage stand are
securely positioned over cradle pins (#3). Secure
storage stand to cradle with clamping knobs (#11).
2. Without starting the tractor, lower boom (#14) to rest
yoke hitchpinssecurely in supportangles onthestorage
stand. Some adjustment to the support angles may be
required.
3. Disconnect 3-point hitch.
4. Start tractor and drive away being careful not to catch on
the Post Hole Digger and Storage Stand.
PD15, 25, and 35 Storage Stand Assembly
Figure 4
NOTE: Do not disconnect Post Hole Digger from a
tractor on a steep slope. Injury to personnel and
equipment may result.
20872

10/06/08 Post Hole Digger Storage Stand Assembly Instructions Manual No. 317-189M 5
Land Pride
Listing of Parts
■
1 317-142A PD15, PD25 & PD35 STAND ASSEMBLY
2 317-143H PD STAND HITCH WELDMENT 1
3 317-144H PD STAND CRADLE WELDMENT 1
4 317-148H PD STAND HITCH WELDMENT 2
5 317-153B PD STAND HARDWARE BAG 1
6 802-034C HHCS 1/2-13X1 1/4 GR5 4
7 803-147C NUT HEX NYLOCK 1/2-13 2
8 804-015C WASHER LOCK SPRING 1/2 PLT 2
9 804-016C WASHER LFAT 1/2 SAE PLT 2
10 817-455C KNOB 1/2-13 MALE THD 2 3/8OD 2
11 838-298C DECAL CAUTION DO NOT LEAN ON 2
Kit No. 317-142A PD15, PD25 & PD35 Storage Stand Assembly
Item Part No. Part Description Qty

Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com