Landmann 28925 User manual

PLEASE READ ALL RULES FOR SAFE
OPERATION BEFORE ASSEMBLY AND
HELPFUL HINTS BEFORE USE.
ASSEMBLY INSTRUCTIONS
Congratulations on your purchase of the Ball 'O Fire! At Landmann USA,
we strive to provide you with an easy to use, easy to assemble product.
However, in the unlikely event your package should have a missing or
defective part, please contact us at:
[e-mail]
-OR-
1-800-321-3473 M-F 8-5 Eastern Time
Proof of purchase may be required. Thank you!
Landmann USA
Cartersville, GA 30120
www.landmann-usa.com
Made in China
© 2008 Landmann USA
BALL 'O FIRE™
MODEL 28924, 28925
!
PAGE 1
VER. 6, 7/28/08
• FOR OUTDOOR USE ONLY!
• USE ONLY ON BRICK, CONCRETE, STONE OR OTHER MASONRY
SURFACES!
• DO NOT USE ON LAWNS, WOODEN DECKS OR ASPHALT!
• THE BALL 'O FIRE MUST BE PLACED ON A LEVEL SURFACE.
• DO NOT USE WITHOUT FIREBOWL, THE FIREBOWL MUST BE
USED AT ALL TIMES!
• FIREWOOD MUST BE KEPT WITHIN THE BOUNDARIES OF THE
FIREBOWL.
• FIREWOOD MUST NOT BE ALLOWED TO TOUCH ANY PART OF
THE SCREEN.
• FOR LONGER LIFE, KEEP FIRES TO A RESPECTABLE SIZE, DO
NOT OVERLOAD.
• DO NOT BURN LEAVES OR GARBAGE IN THE BALL 'O FIRE.
• KEEP THE BALL 'O FIRE AWAY FROM BUILDINGS, FLAMMABLE
ITEMS AND VEHICLES.
• THE BALL 'O FIRE IS FOR ADULT USE ONLY.
• DO NOT LEAVE UNATTENDED AT ANY TIME WHILE IN USE.
• KEEP SPARK GUARD DOOR CLOSED WHILE IN USE.
• DO NOT USE IN WINDY CONDITIONS!
• NEVER USE GASOLINE, ALCOHOL OR VOLATILE FLUIDS TO
START FIRES.
• NEVER USE UNDER LOW HANGING TREE BRANCHES, TRELLIS,
OVERHANGS OF ANY KIND INCLUDING COVERED PORCHES.
• USE CAUTION WHEN TENDING THE FIRE, AS SURFACES WILL
BE HOT WHILE IN USE.
• USE MITTENS OR POKER IF NECESSARY TO OPEN THE SPARK
GUARD DOOR.
• BEFORE EACH USE MAKE SURE THE BALL 'O FIRE IS IN GOOD
WORKING CONDITION.
• USE CAUTION AFTER THE FIRE HAS BEEN EXTINGUISHED,
SURFACES WILL REMAIN HOT FOR SOME TIME.
• USE THE COVER ONLY AFTER THE BALL 'O FIRE HAS
COMPLETELY COOLED.
READ FIRST!
RULES FOR SAFE OPERATION
!
Assembly and Use
Instructions for Models:
28924, 28925
PRODUCT CODE: O
PRODUCT CODE: O

PARTS LIST:
When unpacking the Ball 'O Fire from the carton, make sure you find and become familiar with all the pieces listed below:
VER. 1, 8/22/07
C
(3) LEGS
P(28)
13MM
BOLTS
(1) COVER
(1) CENTER RING E F G
A B
(3) BOTTOM
SCREEN
SECTIONS
(3) BOTTOM
SCREEN
SECTIONS
(1) LEFT FIXED
TOP SECTION (1) CENTER FIXED TOP SECTION (1) RIGHT FIXED TOP SECTION
HJK
(1) LEFT DOOR
SECTION (1) CENTER DOOR SECTION (1) RIGHT DOOR SECTION
L
M N
(1) CONNECTING
RING
(1) CONNECTING
RING W/ HANDLE (2) BOWL
HANDLES
Q
O
(1) BOWL
UTS (6)
10MM
BOLTS
(6)
20MM
BOLTS
R
(6)
25MM
BOLTS
X
(6)
CAP
NUTS
V
(2)
40MM
BOLTS
Y
(2)
LOCK
WASHERS
W
(52)
HEXNUTS
PAGE 2
BALL 'O FIRE™
IF YOU HAVE MISSING
OR DEFECTIVE PARTS,
PLEASE CALL CUSTOMER
SERVICE AT 1-877-347-4557 FOR OUTDOOR
USE ONLY
!
Z
(2)
FLAT
WASHERS

STEP 2
Assemble (1) pc
screen section [A]
to the screens using
(2) 13MM bolts, (1)
25MM bolt and (3)
hexnuts as shown.
Assemble the
25MM bolt where
shown. Only finger
tighten at this time.
STEP 4
Assemble the (3)
legs [D] to the
screen bowl using
(6) hexnuts.
Securely tighten the
bolts.
STEP 3
Following the same
instructions in steps
1 and 2, continue to
alternate and
assemble the
remaining screen
sections [A,B] until
the screen bottom
is formed.
PAGE 3
BALL 'O FIRE™
STEP 1
Find (1) pc each of
the bottom screen
sections [A,B].
Assemble together
using (2) 13MM
bolts, (1) 25MM bolt
and (3) hexnuts as
shown. Assemble
the 25MM bolt
where shown. Only
finger tighten at this
time.
ASSEMBLY INSTRUCTIONS:
D
A
B
A
BA
B
ABA
25MM bolt /
hexnut here
13MM bolt /
hexnut on the
inside
13MM bolt /
hexnut on the
inside
AB
13MM bolt /
hexnut on
the inside 25MM bolt /
hexnut here
13MM bolt /
hexnut on the
inside
STEP 5
Find the center ring
[C] and remove the
pre-assembled
20MM bolts and
hexnuts. Carefully
place the center ring
on the screen
sections aligning the
holes with the center
ring. Assemble with
the (6) 20MM bolts
and hexnuts.
Securely tighten the
bolts.
STEP 6
Assemble screen
sections [E,F,G]
together with (6)
10MM bolts and (6)
cap nuts. Assemble
with the cap nuts on
the outside. Tighten
bolts and cap nuts
securely.
E
F
G
STEP 7
Assemble connecting
ring [L] to the screen
sections using (4)
13MM bolts and
hexnuts. Tighten
securely.
C
L
HJK
STEP 9
Assemble connecting
ring with handle [M]
to the screen
sections using (4)
13MM bolts and
hexnuts. Tighten
securely.
Make sure cap nuts
are assembled on the
outside (STEP 6).
EF
G
STEP 8
Assemble screen
sections [H,J,K]
together with
(6) 13MM bolts and
(6) hexnuts.
Securely tighten the
bolts.
H
J
K
M
IMPORTANT!
IMPORTANT!
IMPORTANT!
NO BOLT
NO BOLT
NO BOLT
NO BOLT
NO BOLT
NO BOLT
NO BOLT

• ADDING SAND TO THE BOTTOM OF
FIREBOWL HELPS PROTECT AGAINST
THE CORROSIVE NATURE OF THE ASHES
AND WILL EXTEND THE LIFE OF
THE FIREBOWL.
• IF YOU ARE NOT GOING TO USE THE
BALL 'O FIRE FOR A LONG PERIOD
OF TIME, STORE AWAY OUT OF THE
WEATHER OR USE THE COVER TO KEEP
DRY.
• DO NOT LET FIREBOWL FILL WITH
WATER.
• DO NOT DUMP ASHES WHERE THEY
COULD START A FIRE.
• DISPOSE OF ASHES IN PROPER
RECEPTACLE ONLY AFTER ASHES HAVE
COOLED.
HELPFUL HINTS
STEP 10
Assemble the fixed
screen sections
[E,F,G] to the center
ring using (2) 13MM
bolts and hexnuts.
Tighten securely.
BALL 'O FIRE™
ASSEMBLY INSTRUCTIONS:
STEP 12
Assemble door
screen section
[H,J,K] to the pivot
pins as shown.
Squeeze the ends
of the door together
if necessary and
insert into the pins.
Assemble the door
with (2) 40MM bolts,
flat washers, lock
washers and
hexnuts. Assemble
as shown.
Place the firebowl
on the inside and
onto the 25MM
bolts.
The Ball 'O Fire is
ready for use.
Enjoy!
STEP 11
Assemble the bowl
handles [N] to the
bowl [O] using (4)
hexnuts. Tighten
securely.
PAGE 4
DO NOT RETURN PRODUCT TO
THE STORE. IF YOU HAVE
QUESTIONS OR TROUBLE
WITH ASSEMBLY, PLEASE
CALL 1-877-347-4557
FOR ASSISTANCE.
WARNING!
!
DO NOT USE WITHOUT FIREBOWL,
THE FIREBOWL MUST BE USED AT
ALL TIMES. KEEP FIREWOOD
WITHIN THE BOUNDARIES OF THE
FIREBOWL. DO NOT PILE WOOD ON
ANY SCREEN PART. FIREWOOD
MUST NOT BE ALLOWED TO TOUCH
ANY PART OF THE SCREEN. FOR
LONGER PRODUCT LIFE, KEEP
FIRES TO A RESPECTABLE SIZE,
DO NOT OVERLOAD.
Hexnut
13MM bolt
40MM bolt
Lock washer
Hexnut
Flat washer