Lantronix EDS3000PR User manual




1. HARDWARE OVERVIEW
2. INSTALLATION
EDS3000PR Device Server Quick Start Guide

1.RTS (Out)
2.DTR (Out)
3.TX (Out)
4.GND
5.GND
6.RX (In)
7.DSR (In)
8.CTS (In)
RS‐232 Pin Assignment
! ThankyouforchoosingLantronix.PleaseregistertheEDS3000PRinordertoreceivenoficaonsfor
firmwareanddocumentaonupdatesatwww.lantronix.com/product‐registraon.
EDS3000PR
Quick Start Accessories Part Number
PowerCord500‐041‐R
RJ45toDB9FAdapter500‐103‐R
START
WHAT’S IN THE BOX
1.InstalltheEDS3000PRina19”rack.
2.PowerofftheserialdevicethatwillbeconnectedtotheEDS3000PR.
3.AachaCAT5serialcablebetweentheEDS3000PRandyourserial
device.
4.ConnectanEthernetcablebetweentheEDS3000PREthernetportand
yourEthernetnetwork.
5.Connectthepowercordandapplypower.
6.Poweruptheserialdevice.


EDS3008PR,EDS3016PR,orEDS3032PR.
(EDS3032PRshownhere.)
Otheradaptersareavailableandaresold
separately.
SpeedLED
AcvityLED
RJ45EthernetPort
ConsolePortResetSwitch
StatusLED
PowerLED
ReceiveLED(le)TransmitLED(right)
RJ45SerialPortPowerConnector
EDS3032PRFrontView
EDS3032PRBackView




4. IP ADDRESS CONFIGURATION
EDS3000PR Device Server Quick Start Guide


IftheEDS3000PRwasnotassignedanIPaddressau‐
tomacallythroughDHCP,youmustassignonevia
CLI.IfitwassuccessfullyassignedanIPaddress
throughDHCP,youcanchangetheconfiguraonvia
theWebManagerorCLI.Thedevice’sfactorydefault
usernameis“admin”andfactorydefaultpasswordis
thelast8charactersoftheDeviceID.Seethe
EDS3000PRproductUserGuideandCommandRefer‐
encefordetailedinstruconsat
hp://www.lantronix.com/support/downloads.

ToconfiguretheIPaddressmanually,youneedthe
followinginformaon:

IPaddress:______.______.______.______
Subnetmask:______.______.______.______
Gateway:______.______.______.______
DNS:______.______.______.______

©2023Lantronix,Inc.Lantronix isaregisteredtrademarkofLantronix,Inc.Allothertrademarksarethepropertyofrespecveowners.
Specificaonssubjecttochangewithoutnoce.895‐0011‐00Rev.B
Contact Technical Support
Fortechnicalsupportqueries,visithps://www.lantronix.com/support.
Latest Firmware Forthelatestfirmwaredownloads,visithps://www.lantronix.com/support/downloads
To configure via Web Manager:
1.EnterthedeviceIPaddressintheaddressbarofa
browser.
2.LogintotheEDS3000PR.
3.Changenetworksengs,ifneeded,inNetwork>
WiredNetwork>Interface>Configuraon,or
performotherconfiguraon.

To configure via Command Line:
1.Connectviaaterminalemulatoroverserialorvia
Telnet(iftheEDS3000PRalreadyhasanIPad‐
dress).
2.LogintotheEDS3000PR.
3.Changenetworksengs,ifneeded,inenable>
config>if1,orperformotherconfiguraon.
3. DEVICE DISCOVERY
TheEDS3000PRmusthaveauniqueIPaddresson
yournetwork.ThisIPaddresscanbeassignedauto‐
macallywithDHCP,oryoucanassignitmanually.
TheEDS3000PRlooksforaDHCPserverwhenitfirst
powersuptoassignanIPaddress.YoucanuseLant‐
ronixProvisioningManagertolocatetheautomacal‐
lyassignedIPaddress.
1.DownloadthelatestversionofLantronixProvi‐
sioningManagerfromhps://
www.lantronix.com/products/lantronix‐
provisioning‐manager/.
2.InstallLantronixProvisioningManager.
3.RunLantronixProvisioningManager.
4.IfthisisyourfirstmerunningLantronixProvi‐
sioningManager,proceedthroughtheinialset‐
up.
5.Locateyourdeviceinthedevicelistandnotethe
IPaddress.

Fordetailedinstrucons,seetheLantronixProvision‐
ingManageronlinehelpat
hps://docs.lantronix.com/products/lpm/.