Lantronix SISPM1040-582-LRT User manual

SISPM1040-582-LRT
Managed Hardened PoE++ Switch (8) 10/100/1000Base-T PoE++ Ports + (2)
100/1000Base-X SFP Slot
CLI Reference
Part Number 33757
Revision J November 2023

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 2of 272
Intellectual Property
© 2022, 2023 Lantronix, Inc. All rights reserved. No part of the contents of this publication may be transmitted or
reproduced in any form or by any means without the written permission of Lantronix.
Lantronix is a registered trademark of Lantronix, Inc. in the United States and other countries.
Patented: https://www.lantronix.com/legal/patents/; additional patents pending.
Warranty
For details on the Lantronix warranty policy, go to http://www.lantronix.com/support/warranty.
Contacts
Lantronix Corporate Headquarters
48 Discovery, Suite 250
Irvine, CA 92618, USA
Toll Free: 800-526-8766
Phone: [phone]
Fax: [phone]
Technical Support
Online: https://www.lantronix.com/technical-support/
Sales Offices
For a current list of our domestic and international sales offices, go to www.lantronix.com/about/contact.
Disclaimer
All information contained herein is provided “AS IS.” Lantronix undertakes no obligation to update the information
in this publication. Lantronix does not make, and specifically disclaims, all warranties of any kind (express, implied
or otherwise) regarding title, non-infringement, fitness, quality, accuracy, completeness, usefulness, suitability or
performance of the information provided herein. Lantronix shall have no liability whatsoever to any user for any
damages, losses and causes of action (whether in contract or in tort or otherwise) in connection with the user’s
access or usage of any of the information or content contained herein. The information and specifications
contained in this document are subject to change without notice.
Revision History
Date
Rev
Description
9/28/21 G
FW VB7.20.0075: add API command “get_config_action_status” and fix API cannot delete old
interface VLAN. Fix PoE Power Requested and Power Allocated not match. Add DI reboot switch
when DI input goes High and fix DDM information updating. Fix DI/DO bug and fix PMD auto
negotiation advertised capability info in LLDP packet of fiber ports. Fix Port issue with TN-EOT-
CO and TN-EOT-RT copper modules. Add ‘ SystemDORelayOpenClose’ to MIB. Add note on
debug command use.
9/28/22 H
FW vB.7.20.0121: update RADIUS server and add two new DMS icons. Initial Lantronix rebrand.
Add First Time Wizard and DHCP IP per port and update SNMP and Auth Method default
settings. Add DHCP option 229 (lighting server). Add ConsoleFlow and LPM features and update
DMS Google Maps API information. Remove CLI command summary.
11/7/23 J
Change ConsoleFlow to Percepxion. Add DHCP per Port VLAN. Update SSH. Update to TLSv1.2
ciphers. Add two public OIDs. Automatically save config changes to Start-Up Configuration in
Percepxion server. FW v B7.20.0191: Add API support in HTTPS. Update to Dropbear 2022.82.

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 3of 272
Contents
1 Introduction....................................................................................................................................................... 5
1.1 Key Features .................................................................................................................................................. 5
1.2 Manual Overview ........................................................................................................................................... 5
1.3 Related Manuals ............................................................................................................................................ 5
2CLI Management............................................................................................................................................. 6
2.1 Login............................................................................................................................................................... 6
2.2 Navigating the Command Line....................................................................................................................... 6
2.3 CLI Command Modes .................................................................................................................................... 7
2.4 Changing Between Command Modes ........................................................................................................... 7
2.5 Command Line Messages ............................................................................................................................. 7
2.6 Privilege Levels .............................................................................................................................................. 8
2.7 Exec Mode (Global) Commands .................................................................................................................... 8
3Clear Commands.......................................................................................................................................... 14
4Configure Mode Commands ....................................................................................................................... 24
5Copy Commands........................................................................................................................................ 110
6Delete Commands ...................................................................................................................................... 111
7Dir Commands............................................................................................................................................ 111
8Disable Commands .................................................................................................................................... 112
9Do Commands ............................................................................................................................................ 112
10 Dot1x Commands....................................................................................................................................... 113
11 Enable Commands ..................................................................................................................................... 115
12 ERPS Commands ....................................................................................................................................... 116
12.1 ERPS Exec Mode Commands ................................................................................................................. 116
12.2 ERPS Config Mode Commands............................................................................................................... 117
13 Firmware Commands................................................................................................................................. 119
14 IPv4 Commands ......................................................................................................................................... 120
15 IPv6 Commands ......................................................................................................................................... 120
16 Link OAM Commands................................................................................................................................ 121
17 No Commands ............................................................................................................................................ 122
18 Ping Commands ......................................................................................................................................... 127
19 Platform Commands .................................................................................................................................. 128
20 PTP Commands.......................................................................................................................................... 129
21 Reload Commands..................................................................................................................................... 130
22 Send Commands ........................................................................................................................................ 130
23 Show Commands ....................................................................................................................................... 131
24 Terminal Commands.................................................................................................................................. 207
25 Traceroute Commands .............................................................................................................................. 208

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 4of 272
26 Interface Config Mode Commands........................................................................................................... 209
26.1 Configure and Show Port Events for an Interface.................................................................................... 242
26.2 Configure QoS Commands for an Interface............................................................................................. 244
27 MRP Pre-Requisites and Application Examples ..................................................................................... 246
27.1 MRP Description ...................................................................................................................................... 246
27.2 MRP Operation ........................................................................................................................................ 246
27.3 Related Devices ....................................................................................................................................... 246
27.4 MRP Sample Setup.................................................................................................................................. 247
27.5 MRP Pre-Requisites (General) ................................................................................................................ 247
27.6 MRP Config Mode Command Parameters .............................................................................................. 248
27.7 MRP Config Mode Command Syntax ...................................................................................................... 248
27.8 MRP Setup (CLI Commands) .................................................................................................................. 249
28 Service and Tech Support......................................................................................................................... 251
28.1 Recording Device and System Information.............................................................................................. 251
Appendix A DHCP Per Port ........................................................................................................................ 252
Appendix B SFTP copy Commands .......................................................................................................... 255
Secure File Transfer (SFTP) Setup.................................................................................................................. 255
Solar Wind Settings.......................................................................................................................................... 258
SFTP Client Copy Commands ......................................................................................................................... 260
Copy (Upload) config Commands .................................................................................................................... 261
Copy (Download) config Commands ............................................................................................................... 261
Copy (Upload) config Commands .................................................................................................................... 261
Firmware Upgrade Commands ........................................................................................................................ 262
Appendix C Percepxion and LPM Commands ......................................................................................... 263
Command Set .................................................................................................................................................. 263
Command Descriptions .................................................................................................................................... 263
Appendix D Service, Warranty & Tech Support ....................................................................................... 271
Appendix E Compliance Information ........................................................................................................ 271

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 5of 272
1Introduction
The SISPM1040-582-LRT is a managed PoE++ switch suitable for connecting and powering devices in hardened
environments. It has (8) 10/100/1000 PoE++ ports with (2) 100/1000 dual speed SFP slots. The switch can supply
up to 90 Watts per port on (4) ports or 60 Watts per port on (8) ports simultaneously. The switch also includes the
embedded Device Management System (DMS) software that provides the advanced tools necessary for total
management of all IP addressable devices. The unique DMS provides security integrators with lower overall cost,
less downtime and easier management of the entire PoE+ network. Lantronix hardened switches are certified to
operate reliably in harsh environments such as those found on factory floors, outdoor enclosures or other
challenging environments.
1.1 Key Features
Rapid Ring / Ring To Ring / Rapid Chain
DMS (Device Management System) built in
IEEE 802.3af/at/bt PoE++ Power over Ethernet
ITU-T G.8031 Ethernet Linear Protection Switching (EPS)
ITU-T G.8032 Ethernet Ring Protection Switching (ERPS)
IEEE 1588v2 PTP
IEEE 802.3ah OAM
IEEE 802.1ag CFM (ITU-T Y.1731 Performance Monitoring)
DHCP Server, DHCP Relay, DHCP Snooping, DHCP Per Port
IEEE 802.3az Energy Efficient Ethernet (EEE) for green Ethernet applications
IPv4/IPv6 L3 static route
Percepxion and LPM support
1.2 Manual Overview
This manual gives specific information on how to operate and use the management functions of the switch via its
Command Line Interface (CLI). This manual is intended for use by network administrators who are responsible for
operating and maintaining network equipment; it assumes a working knowledge of general switch functions, the
RS-232 Console , Internet Protocol (IP), and Telnet Protocol.
1.3 Related Manuals
•SISPM1040-582-LRT Quick Start Guide, 33754
•SISPM1040-582-LRT Install Guide, 33755
•SISPM1040-582-LRT Web User Guide, 33756
•SISPM1040-582-LRT CLI Reference, 33757 (this manual)
•SISPM1040-582-LRT API User Guide, 33826
Go to the Lantronix Resource Center for Lantronix Firmware, Manuals, Tech Support, Knowledge Base, FAQs, etc.
Note that this manual provides links to third part web sites for which Lantronix is not responsible.
For SFP or SFP+ information see Lantronix SFP webpage.
Note that this manual provides links to third party web sites for which Lantronix is not responsible.

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 6of 272
2 CLI Management
Follow the steps below to make a network connection for CLI command management.
1. Locate the correct DB-9 (RS-232) cable with a female DB-9 connector. RS-232 cable is used for connecting a
terminal or terminal emulator to the Managed Switch’s RJ45 port to access the command line interface.
2. Attach the RJ45 serial port on the switch’s front panel which used to connect to the switch for console
configuration
3. Attach the other end of the DB-9 cable to an ASCII terminal emulator or PC Com-1, 2 port. For example, PC
runs Microsoft Windows HyperTerminal utility.
4. At “Com Port Properties” menu, configure the parameters as below (see the next section).
Baud rate 115200
Stop bits 1
Data bits 8
Parity N
Flow control none
2.1 Login
The command-line interface (CLI) is a text-based interface. You can access the CLI via either a direct serial
connection to the device or a Telnet session (default IP address: 192.168.1.77). The default username and
password to login into the Managed Switch are listed below:
Username: admin
Password: admin
After you log in successfully, the prompt displays as “<sys_name>#“. It means you are an administrator and have
full privileges for configuring the switch. If not logged in as the administrator, the prompt will be shown as
“<sys_name>>”, which means you are a guest and are not allowed the full set of CLI commands. Each CLI
command has its privilege level of 0-15.
2.2 Navigating the Command Line
To display
Press
Description
more
-
dash key
next page
Space
space bar
continue
g
g key
quit
^C
Control C
parameters
?
Single question mark
syntax
??
Two question marks
available commands in table format
Tab key
available commands in table format

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 7of 272
2.3 CLI Command Modes
The CLI is divided into several modes. If a user has enough privilege to run a particular command, the user has to
run the command in the correct mode. To see the commands of the mode, enter a “?” after the system prompt,
then all commands will be listed in the screen. The command modes are listed as below:
Command Modes
Mode
Prompt
Command Function in this Mode
exec <sys_name>#
Display current configuration, diagnostics,
maintenance
config
<sys_name>(config)#
Configure features other than those below
Config-if
<sys_name>(config-interface)#
Configure ports
Config-if-vlan
<sys_name>(config-if-vlan)#
Configure static vlan
Config-line
<sys_name>(config-line)#
Line Configuration
Config-impc-profile
<sys_name>(config-impc-profile)#
IPMC Profile
Config-snmp-host
<sys_name>(config-snmp-host)#
SNMP Server Host
Config-stp-aggr
<sys_name>(config-stp-aggr)#
STP Aggregation
Commands reside in a specific mode and can only be run in that mode. To run a particular command, you must
change to the appropriate mode. The command modes are organized as a tree, and you start in Exec mode.
The following table explains how to change from one mode to another.
2.4 Changing Between Command Modes
Mode
Enter Mode
Leave Mode
exec
--
--
config
Configure terminal
exit
config-interface
Interface <port-type> <port-type-list>
exit
config-vlan
Interface vlan <vlan_list>
exit
2.5 Command Line Messages
Message: Wrong username or password!
Recovery: Re-try the login with the correct username and password credentials.
Message: There are too many users in the system.
Recovery: Try to log in later.
Message: % Incomplete command.
Recovery: Try entering the command again with all required parameters.
Message: % Invalid word detected at '^' marker.
Recovery: Try entering the command again with correctly entered parameters.

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 8of 272
2.6 Privilege Levels
Every command has a privilege level (0-15). Users can run a command if the session’s privilege level is greater
than or equal to the command’s privilege level. The session’s privilege level initially comes from the login
account’s privilege level, though it is possible to change the session’s privilege level after logging in.
Privilege Level
Types of Commands at this Privilege Level
0
Display basic system information.
13
Configure features except for login accounts, the authentication method
sequence, multiple logins, and administrator and enable passwords.
15
Configure login accounts, the authentication method sequence, multiple logins, and
administrator and enable passwords.
2.7 Exec Mode (Global) Commands
Enter a question mark (?) at the command line prompt to display the global Exec mode commands.
SISPM1040-582-LRT# ?
CableDiag Cable Diagnostic keyword
clear Reset functions
configure Enter configuration mode
copy Copy from source to destination
debug Debugging functions
delete Delete one file in flash: file system
dir Directory of all files in flash: file system
disable Turn off privileged commands
do To run exec commands in config mode
dot1x IEEE Standard for port-based Network Access Control
enable Turn on privileged commands
erps Ethernet Ring Protection Switching
exit Exit from EXEC mode
firmware Firmware upgrade/swap
help Description of the interactive help system
ip IPv4 commands
ipv6 IPv6 configuration commands
link-oam Link OAM configuration
logout Exit from EXEC mode
more Display file
no Negate a command or set its defaults
ping Send ICMP echo messages
platform Platform configuration
ptp Misc non persistent 1588 settings
reload Reload system.
send Send a message to other tty lines
show Show running system information
terminal Set terminal line parameters
traceroute traceroute program
SISPM1040-582-LRT#
The global Exec mode commands are described below.

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 9of 272
Command: ?or ?? or Tab
Description: Enter one question mark (?) with no space in the command line to display a command
description.
Enter one question mark (?) with space in the command line to display the parameters available.
Enter two question marks (??) in the command line to display the syntax available.
Press the Tab key to display available commands in table format.
Syntax : ?(with or without space before)
?? (without space before)
<Tab>
Parameters: None.
Example 1: Enter a single question mark (?) in the command line to display the parameters available.
SISPM1040-582-LRT# show ?
aaa Authentication, Authorization and Accounting methods
access Access management
access-list Access list
aggregation Aggregation port configuration
always-on-poe Show Always On PoE Status
clock Configure time-of-day clock
command-history-log Command Histry List
dot1x IEEE Standard for port-based Network Access Control
eps Ethernet Protection Switching
erps Ethernet Ring Protection Switching
evc Ethernet Virtual Connections
event Show trap event configuration
green-ethernet Green ethernet (Power reduction)
history Display the session command history
interface Interface status and configuration
ip Internet Protocol
ipmc IPv4/IPv6 multicast configuration
ipv6 IPv6 configuration commands
lacp LACP configuration/status
line TTY line information
-- more --, next page: Space, continue: g, quit: ^C
Example 2: Enter two question marks (??) in the command line to display the syntax available.
SISPM1040-582-LRT# show??
show aaa
show access management [ statistics | <access_id_list> ]
show access-list [ interface [ ( <port_type> [ <v_port_type_list> ] ) ] ] [ rate-limiter [
<rate_limiter_list> ] ] [ ace statistics [ <ace_list> ] ]
show access-list ace-status [ static ] [ link-oam ] [ loop-protect ] [ dhcp ] [ptp ] [ upnp ] [ arp-
inspection ] [ evc ] [ mep ] [ ipmc ] [ ip-source-guard ] [ ip-mgmt ] [ tt-loop ] [ y1564 ] [ dms-
client ] [ dms-server ] [ dms-ssdp ] [ dms-onvif ] [ agv-car ] [ dms-mdns ] [ ztp ] [ rapid-ring ] [
lacp-on-air ] [ mrp] [ conflicts ] [ switch <switch_list> ]
show aggregation [ mode ]
show clock
show clock detail
show command-history-log status
show dot1x statistics { eapol | radius | all } [ interface ( <port_type> [ <v_port_type_list> ] ) ]
show dot1x status [ interface ( <port_type> [ <v_port_type_list> ] ) ] [ brief ]
show eps [ <inst> ] [ detail ]
show erps { [ <groups> ] } [ detail | statistics ]
show evc statistics { [ <evc_id> | all ] } [ ece [ <ece_id> ] ] [ interface ( <port_type> [
<port_list> ] ) ] [ pw <pw_num_list> ] [ cos <cos> ] [ green | yellow | red | discard ] [ frames |
bytes ]
-- more --, next page: Space, continue: g, quit: ^C

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 10 of 272
Example 3: Press the Tab key to display available commands in table format.
SISPM1040-582-LRT# show <tab>
aaa access access-list
aggregation always-on-poe clock
command-history-log dot1x eps
erps evc event
green-ethernet history interface
ip ipmc ipv6
lacp line link-oam
lldp logging loop-protect
mac map-api-key mep
monitor mrp mvr
ntp platform poe
port-security privilege process
ptp pvlan qos
radius-server rapid-ring rmon
running-config sflow smtp
snmp spanning-tree switchport
system tacacs-server terminal
udld upnp user-privilege
users version vlan
voice web
SISPM1040-582-LRT#
Command: CableDiag
Description: Run Cable Diagnostic test on copper ports.
Syntax : CableDiag interface <port_type> <port_type_id>
Parameters: interface Interface keyword
GigabitEthernet 1 Gigabit Ethernet Port
<port_type_id> Port ID in 1/1-8
Example:
SISPM1040-582-LRT# CableDiag interface GigabitEthernet 1/3
Starting Cable Diagnostic - Please wait
Interface Link Status Test Result Length
---------------------- ------------- ------------- -------------
GigabitEthernet 1/3 Link Down detect error or check cable length is between 7-120 meters
SISPM1040-582-LRT# CableDiag interface GigabitEthernet 1/8
Starting Cable Diagnostic - Please wait
Interface Link Status Test Result Length
---------------------- ------------- ------------- -------------
GigabitEthernet 1/8 1G detect error or check cable length is between 7-120 meters
SISPM1040-582-LRT# CableDiag interface GigabitEthernet 1/7
Starting Cable Diagnostic - Please wait
Interface Link Status Test Result Length
---------------------- ------------- ------------- -------------
GigabitEthernet 1/7 Link Down Abnormal 3(m)
SISPM1040-582-LRT#
Messages: % No such interface: GigabitEthernet 1/9 displays if you enter the command on a fiber port.

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 11 of 272
Command: dot1x
Description: IEEE Standard for port-based Network Access Control in Exec mode.
Syntax : dot1x initialize [ interface ( <port_type> [ <plist> ] ) ]
Parameters: initialize Force re-authentication immediately
interface Interface
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
<port_type_list> Port list in 1/1-10
Example:
SISPM1040-582-LRT# dot1x initialize interface * 1/5 GigabitEthernet 1/5
SISPM1040-582-LRT# dot1x initialize
SISPM1040-582-LRT#
Command: Exit
Description: Exit from EXEC mode.
Syntax : exit
Parameters: None
Example:
SISPM1040-582-LRT# exit
Username:
Password:
Wrong username or password!
Username: admin
Password:
SISPM1040-582-LRT# con ter
SISPM1040-582-LRT(config)# exit
SISPM1040-582-LRT# exit?
exit Exit from EXEC mode
<cr>
SISPM1040-582-LRT#

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 12 of 272
Command: Help
Description: Description of the interactive help system.
Syntax : help
Parameters: None
Example:
SISPM1040-582-LRT# help
Help may be requested at any point in a command by entering
a question mark '?'. If nothing matches, the help list will
be empty and you must backup until entering a '?' shows the
available options.
Two styles of help are provided:
1. Full help is available when you are ready to enter a
command argument (e.g. 'show ?') and describes each possible
argument.
2. Partial help is provided when an abbreviated argument is entered
and you want to know what arguments match the input
(e.g. 'show pr?'.)
SISPM1040-582-LRT#
Command: Logout
Description: Exit from EXEC mode.
Syntax : logout <cr>
Parameters: Press Enter to log back in.
Example:
SISPM1040-582-LRT# logout
Username:
Password:

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 13 of 272
Command: more
Description: Display file.
Syntax : more <path>
Parameters:
<url_file> File in FLASH or on TFTP server. Syntax: <flash:filename | tftp://server/path-and-filename>.
A valid file name is a text string drawn from alphabet (A-Za-z), digits (0-9), dot (.), hyphen (-),
under score (_). The maximum length is 57 characters and a hyphen must not be first character.
The file name content that only contains '.' is not allowed.
Example:
SISPM1040-582-LRT# more?
more Display file
SISPM1040-582-LRT# more?
more <path>
SISPM1040-582-LRT# more tftp://server/path-and-filename
% Loading /path-and-filename from TFTP server server
SISPM1040-582-LRT#
Messages: % TFTP load error: Network error

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 14 of 272
3 Clear Commands
Command Function
access Access management
access-list Access list
dot1x IEEE Standard for port-based Network Access Control
eps Ethernet Protection Switching.
erps Ethernet Ring Protection Switching
evc Ethernet Virtual Connections
ip Interface Internet Protocol config commands
ipv6 IPv6 configuration commands
lacp Clear LACP statistics
link-oam Clear Link OAM statistics
lldp Clears LLDP statistics.
logging System logging message
mac MAC Address Table
mep Maintenance Entity Point
mvr Multicast VLAN Registration configuration
port-security Enable/disable port security globally.
ptp Precision Time Protocol
sflow Statistics flow.
spanning-tree STP Bridge
statistics Clear statistics for one or more given interfaces
Command: access
Description: Clear Access management.
Syntax : access
Parameters: None
Example:
SISPM1040-582-LRT# clear access management statistics ?
<cr>
SISPM1040-582-LRT# clear access management statistics
SISPM1040-582-LRT#
Command: access list
Description: Clear Access list.
Syntax : clear access-list ace statistics
Parameters:
ace Access list entry
statistics Traffic statistics
Example:
SISPM1040-582-LRT# clear access-list ace statistics
SISPM1040-582-LRT#

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 15 of 272
Command: dot1x
Description: Clear IEEE Standard for port-based Network Access Control.
Syntax : clear dot1x statistics
clear dot1x statistics [ interface ( <port_type> [ <v_port_type_list> ] ) ]
Parameters: statistics Clears the statistics counters
interface Interface
GigabitEthernet 1 Gigabit Ethernet Port
PORT_TYPE_LIST Port list in 1/1-10 for Gigabitethernet
Example:
SISPM1040-582-LRT# clear dot1x statistics?
interface <cr>
SISPM1040-582-LRT# clear dot1x statistics
SISPM1040-582-LRT# clear dot1x statistics interface ?
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
SISPM1040-582-LRT# clear dot1x statistics interface GigabitEthernet 1/2-4
SISPM1040-582-LRT#
Command: eps
Description: Clear Ethernet Protection Switching.
Syntax : clear eps <inst> wtr
Parameters:
<uint> The EPS instance number.
wtr Clear active WTR
Example:
SISPM1040-582-LRT# clear eps 1 wtr?
wtr Clear active WTR.
<cr>
SISPM1040-582-LRT# clear eps 1 wtr
Error: EPS instance is not created
SISPM1040-582-LRT#

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 16 of 272
Command: erps
Description: Clear Ethernet Ring Protection Switching.
Syntax : clear erps [ <groups> ] statistics
Parameters:
1~64 Zero or more ERPS group numbers
statistics Clear ERPS statistics
Example:
SISPM1040-582-LRT# clear erps ?
1~64 Zero or more ERPS group numbers
statistics Clear ERPS statistics
SISPM1040-582-LRT# clear erps 1 ?
statistics Clear ERPS statistics
SISPM1040-582-LRT# clear erps 1 statistics ?
<cr>
SISPM1040-582-LRT# clear erps 1 statistics
% No such ERPS group: 1
SISPM1040-582-LRT# clear erps?
erps Ethernet Ring Protection Switching
SISPM1040-582-LRT# clear erps?
clear erps [ <groups> ] statistics
SISPM1040-582-LRT# clear erps
Command: evc
Description: Clear Ethernet Virtual Connections.
Syntax : clear evc statistics { [ <evc_id> | all ] } [ ece [ <ece_id> ] ] [ interface ( <port_type> [ <port_list> ] )
] [ pw <pw_num_list> ]
Parameters:
statistics Statistic counters
interface Interface
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
<port_type_list> Port list for all port types
<cr>
Example:
SISPM1040-582-LRT# clear evc?
evc Ethernet Virtual Connections
SISPM1040-582-LRT# clear evc?
clear evc statistics { [ <evc_id> | all ] } [ ece [ <ece_id> ] ] [ interface ( <port_type> [
<port_list> ] ) ] [ pw <pw_num_list> ]
SISPM1040-582-LRT# clear evc ?
statistics Statistic counters
SISPM1040-582-LRT# clear evc statistics ?
interface Interface
<cr>
SISPM1040-582-LRT# clear evc statistics
SISPM1040-582-LRT# clear evc statistics interface ?
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
SISPM1040-582-LRT# clear evc statistics interface GigabitEthernet 1/3-7
SISPM1040-582-LRT#

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 17 of 272
Command: ip
Description: Clear Interface Internet Protocol config commands.
Syntax :
clear ip arp
clear ip dhcp detailed statistics { server | client | snooping | relay | helper | all } [ interface ( <port_type> [
<in_port_list> ] ) ]
clear ip dhcp relay statistics
clear ip dhcp server binding <ip>
clear ip dhcp server binding { automatic | manual | expired }
clearip dhcp server statistics
clear ip dhcp snooping statistics [ interface ( <port_type> [ <in_port_list> ] ) ]
clear ip igmp snooping [ vlan <v_vlan_list> ] statistics
clear ip statistics [ system ] [ interface vlan <v_vlan_list> ] [ icmp ] [ icmp-msg <type> ]
Parameters: arp Clear ARP cache
dhcp Dynamic Host Configuration Protocol
igmp Internet Group Management Protocol
statistics Traffic statistics
relay DHCP relay agent configuration
snooping DHCP snooping
interface Select an interface to configure
GigabitEthernet 1 Gigabit Ethernet Port
vlan IPv4 traffic interface
<vlan_list> VLAN identifier(s): VID
detailed Detailed statistics
relay DHCP relay agent configuration
server Miscellaneous DHCP server information
snooping DHCP snooping
<ipv4_ucast> IP address of the binding
type Type of bindings to clear
automatic Clear automatic bindings to expired bindings
expired Clear expired bindings for free
manual Clear manual bindings to expired bindings
icmp IPv4 ICMP traffic
icmp-msg IPv4 ICMP traffic for designated message type
interface Select an interface to configure
system IPv4 system traffic
vlan IPv4 interface traffic
Example:
SISPM1040-582-LRT# clear ip arp
SISPM1040-582-LRT# clear ip dhcp detailed statistics all
SISPM1040-582-LRT# clear ip dhcp server binding 192.168.1.11
SISPM1040-582-LRT# $ing statistics interface GigabitEthernet 1/1-10
SISPM1040-582-LRT# clear ip statistics system interface vlan 10
% Failed to clear IPv4 VLAN 10 statistics.
SISPM1040-582-LRT#

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 18 of 272
Command: IPv6
Description: Clear IPv6 configuration commands.
Syntax :
clear ipv6 dhcp-client statistics [ interface vlan <v_vlan_list> ]
clear ipv6 mld snooping [ vlan <v_vlan_list> ] statistics
clear ipv6 neighbors
clear ipv6 statistics [ system ] [ interface vlan <v_vlan_list> ] [ icmp ] [ icmp-msg <type> ]
clear ipv6 statistics [ system ] [ interface vlan <v_vlan_list> ] [ icmp ] [ icmp-msg <type> ]
Parameters: dhcp-client Manage DHCPv6 client service
mld Multicasat Listener Discovery
neighbors Ipv6 neighbors
statistics Traffic statistics
snooping Snooping MLD
statistics Running MLD snooping counters
statistics Traffic statistics
vlan Ipv6 interface traffic
<vlan_list> VLAN identifier(s): VID
icmp IPv6 ICMP traffic
icmp-msg IPv6 ICMP traffic for designated message type
interface Select an interface to configure
system IPv6 system traffic
< 0~255> ICMP message type; ranges from 0 to 255
vlan VLAN of IPv6 interface
vlan Search by VLAN
<vlan_list> IPv6 interface VLAN list
Example:
SISPM1040-582-LRT# clear ipv6 mld snooping vlan 3 statistics
SISPM1040-582-LRT# clear ipv6 neighbors
SISPM1040-582-LRT# Clear ipv6 statistics system icmp icmp-msg 2
SISPM1040-582-LRT# clear ipv6 dhcp-client statistics interface vlan 100
% Invalid DHCPv6 client interface Vlan100
SISPM1040-582-LRT# clear ipv6 statistics icmp icmp-msg 5
SISPM1040-582-LRT#
Command: LACP
Description: Clear LACP statistics.
Syntax : clear lacp statistics
Parameters: statistics Clear all LACP statistics
Example:
SISPM1040-582-LRT# clear lacp statistics
SISPM1040-582-LRT#

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 19 of 272
Command: link-oam
Description: Clear Link OAM statistics.
Syntax : clear link-oam statistics
clear link-oam statistics interface ( * | GigabitEthernet ) <port_type_list>
Parameters: statistics Clear Rx/Tx counters
interface Clear Link OAM statistic on a specific interface or all interfaces.
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
<port_type_list> Port list for all port types
<port_type_list> Port list in 1/1-10
Example:
SISPM1040-582-LRT# clear link-oam?
link-oam Clear Link OAM statistics
SISPM1040-582-LRT# clear link-oam?
clear link-oam statistics [ interface ( <port_type> [ <plist> ] ) ]
SISPM1040-582-LRT# clear link-oam ?
statistics
SISPM1040-582-LRT# clear link-oam statistics ?
interface Clear Link OAM statistic on a specific interface or all
interfaces.
<cr>
SISPM1040-582-LRT# clear link-oam statistics
SISPM1040-582-LRT# clear link-oam statistics interface GigabitEthernet 1/10
SISPM1040-582-LRT#
Command: lldp
Description: Clear LLDP statistics for one or more given interfaces.
Syntax : clear lldp statistics { [ interface ( <port_type> [ <plist> ] ) ] | global }
Parameters: | Output modifiers
global Clear global counters
interface Interface keyword.
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
<port_type_list> Port list in 1/1-10
<cr>
Example:
SISPM1040-582-LRT# clear lldp statistics??
clear lldp statistics { [ interface ( <port_type> [ <plist> ] ) ] | global }
SISPM1040-582-LRT# clear lldp statistics interface GigabitEthernet 1/6-9
SISPM1040-582-LRT# clear lldp statistics
SISPM1040-582-LRT# clear lldp statistics global
SISPM1040-582-LRT#

Lantronix SISPM1040-582-LRT CLI Reference
33757 Rev. J https://www.lantronix.com/ Page 20 of 272
Command: logging
Description: Clear System logging messages.
Syntax :
clear logging [ info ] [ warning ] [ error ] [ emerg ] [ alert ] [ crit ] [ notice ] [ debug ] [ switch <switch_list> ]
clear logging flash
Parameters: alert Severity 1: Action must be taken immediately
crit Severity 2: Critical conditions
debug Severity 7: Debug-level messages
emerg Severity 0: System is unusable
error Severity 3: Error conditions
flash Clear all logging messages on Flash
info Severity 6: Informational messages
notice Severity 5: Normal but significant condition
warning Severity 4: Warning conditions
<cr>
Example:
SISPM1040-582-LRT# clear logging?
logging System logging message
<cr>
SISPM1040-582-LRT# clear logging debug
SISPM1040-582-LRT#
Command: mac
Description: Clear MAC Address table.
Syntax : clear mac address-table
Parameters: address-table Flush MAC Address table.
Example:
SISPM1040-582-LRT# clear mac address-table
SISPM1040-582-LRT#
Command: mep
Description: Clear Maintenance Entity Point.
Syntax : clear mep <inst> { lm | dm | tst | bfd }
Parameters: <uint> The MEP instance.
bfd Clear G.8113.2 BFD CC/CV statistics counters.
dm Clear DM measuring information.
lm Clear LM measuring information.
tst Clear TST measuring information.
Example:
SISPM1040-582-LRT# clear mep 1 dm
Error: MEP instance is not enabled
SISPM1040-582-LRT#