Larson Electronics SLEDB-277V-30C-XMS User manual

SLEDB-277V-30C-XMS
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
SLEDB-277V-30C-XMS
Class II Strobe Light with Motion Sensor
Thank you for your purchase of the Larson Electronics SLEDB-277V-30C-XMS series Strobe Light with Motion
Sensor. This strobe light is completely assembled, tested and ready for installation when shipped from the factory.
Please follow the steps below in order tooperate and maintain this product.
IMPORTANT
READ CAREFULLY BEFORE OPERATING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. IF UNSURE ABOUT ANY
PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICAL PROFESSIONAL.
WARNING: OPERATE ONLY AT THE VOLTAGE LISTED ON THE PRODUCT. DO NOT OPERATE IN CLOSE PROXIMITY OF COMBUSTIBLE
OR FLAMMABLE MATERIALS. NEVER LOOK DIRECTLY AT LIGHT WHEN ON.
WARNING: CONSULT A QUALIFIED ELECTRICAL PROFESSIONAL/ELECTRICIAN TO INSTALL THIS DEVICE IN ACCORDANCE WITH
APPROPRIATE LOCAL AND NEC CODES AND REGULATIONS.
WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
WARNING: DEVICE IS SUITABLE FOR INSTALLATION IN WET LOCATIONS; GFCI PROTECTION RECOMMENDED.
WARNING: ALTHOUGH FIXTURE IS WATERPROOF, IT IS NOT DESIGNED OR INTENDED TO BE SUBMERGED.
WARNING: DO NOT ALLOW LINE VOLTAGE WIRES TO BECOME SUBMERGED!
•ALL OUTDOOR INSTALLATIONS AND INDOOR INSTALLATIONS NEAR A WET LOCATION REQUIRE THE USE OF A GFCI DEVICE FOR
SAFETY, ACCORDING TO THE NATIONAL ELECTRICAL CODE® (NEC).
•KEEP AWAY FROM FLAMMABLE OBJECTS. DO NOT POSITION WITHIN ONE (1) INCH OF ANY COMBUSTIBLE MATERIALS.
•IF DROPPED OR DAMAGED, THE UNIT MAY NO LONGER BE WATERPROOF AND SHOULD BE REPLACED.
•TO AVOID HAZARDS TO CHILDREN, ACCOUNT FOR ALL PARTS AND DESTROY PACKING MATERIALS.
INSTALLATION
This unit comes pre-assembled with
the selected color from factory. Follow
the steps below for installing and
maintaining the strobe light.
MOUNTING
Mount beacon to any flat surface capable of holding its weight utilizing the predrilled mounting holes. Mount in
any direction. Run cable and mount motion sensor within cable length of the beacon. Use the predrilled
mounting holes on the back ofmotion sensor box tomount.
WIRING
We strongly encourage a licensed electrician install this product, especially in outdoor locations where
weatherproofing may be required. Voltage driver permitsoperation at 277VAC.
Warning: Check product label for correct inputvoltage!
Attach supply line wires to the appropriate light fixture
wires as shown in the diagram
Take precautionary steps for weatherproofing all
connections if installed in a location where water may
come in contact with the unit. Ensure the unit is properly
grounded.
If top light output is not required, a circular piece of reflective tape is included to increase visibility to the sides.
Simply remove colored lens held in place by four screws, peel off paper revealing the adhesive side, and stick
reflective tape to the top of lens from the inside with the reflective side facing down, toward the light.
COLOR MAY VARY

SLEDB-277V-30C-XMS
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
MOTION SENSOR
When the motion sensor detects movement, the strobe light is turned on. Once the
motion has stopped, the strobe will stop. Sensitivity, Time Delay and Lux can be
adjusted with their respective control dials on the base of the motion sensor.
1. The SENSITIVITY setting controls the distance in which the motion sensor
will work. The lowest setting will trigger the motion sensor when motion is
close. The highest setting will trigger the motion sensor when motion is far.
2. The TIME setting controls how long the unit remains illuminated following activation & after all motion
ceases. The minimum time (fully anti-clockwise) is approximately 5 seconds and the maximum time
(fully clockwise) is approximately 5 minutes. Set the control to the desired setting between these limits.
3. The LUX setting determines the level of darkness required for the unit to start operating. The setting is
best achieved by the procedure below:
Set the LUX control knob fully anti-clockwise. The unit will now start operating at dusk. If you require the light to
activate earlier, wait until the ambient light level reaches the level of darkness at which you wish the lamp to
become operative, slowly rotate the control in a clockwise direction until a point is reached where the lamp
illuminates. Leave the control set at this point. At this position, the unit should become operative at
approximately the same level of darkness each evening. Observe the operation of the unit. If the unit is starting
to operate too early (e.g. when it is quite light), adjust the control slightly anti-clockwise. If the unit starts to
operate too late (e.g. dusk), adjust the control slightly clockwise. Continue to adjust until the unit operates as
desired.
MOTION SENSOR POSITION
The motion sensor’s position can be adjusted by loosening the hand screw on the side, repositioning, and
tightening the hand screw.
FLASH TUBE REMOVAL
Flash tube is easily removed by inserting a flat blade screwdriver between socket and tube and prying upward,
working around the base of the tube.
MAINTENANCE
If the lens becomes dirty, wipe down with a mild soap and water solution.
It is recommended to occasionally inspect the unit for any defects and to ensure the cable is not frayed and is
gripping tightly in all points of cable contact.
WARRANTY
These instructions may not cover all details or variations of this product for your equipment or installation requirements.
Should further information not covered by these instructions be required, please contact Larson Electronics at
1-800-369-6671 or email [e-mail] for further assistance.
Please visit larsonelectronics.com for Warranty and Return information.