Larson Electronics HAL-36-25W-LED-20C User manual

HAL-36-25W-LED-20C
25 Watt Class 1 Division 2 LED Fixture
20' Cord - Hazardous Location Lighting - 3' Strip
Instruction Manual
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The Larson Electronics HAL-36-25W-LED-20C is a low voltage hazardous location lighting solution approved for Class 1
Division 2 environments and UL 1598 listed for use in wet locations. This powerful 36" long LED strip light produces 1812
lumens, operates from 12 or 24 VDC, and is suitable for a variety of applications.
Mounting Loosen bolt to adjust to
desired angle.
Mounting for this unit is provided by two standard adjustable end brackets
that allow operators to mount the light to flat surfaces and then adjust the
light 170° vertically for the best placement. The entire assembly weighs 2.1
lbs and measures 35.88 inches in length, 2.68 inches wide and 1.69 inches
deep, making it ideal for mounting in areas where space is limited and a low
profile fixture is more readily installed. Use 1/4" screws to secure the fixture
to a flat surface that is capable of supporting the load. Mounting hardware
not provided, but is available for purchase from Larson Electronics if
needed. Once mounted, loosen adjustment screw on the sides to tilt to
desired angle.
Wiring
We strongly encourage a licensed electrician install this product, in all
locations, especially in outdoor areas where weatherproofing may be
required.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in the diagram 
These hazardous location LED lights are equipped with 20 feet of cord
containing a standard two wire (White+ Black-) connecting configuration.
Secure each pair of wires according to the diagram. Utilize a junction box or similar device and take precautionary steps
for weatherproofing all connections if installed in a location where water may come in contact with the unit. Ensure the
unit is properly grounded and that wiring is done according to all local and national electrical/building codes. Light is
instant on, and will illuminate upon receiving the correct voltage.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2

HAL-36-25W-LED-20C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The HAL-36-25W-LED-20C is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.