Larson Electronics EPLC2-EMG-HB-150LED-RT User manual

EPLC2-EMG-HB-150LED-RT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
- EPLC2-EMG-HB-150LED-RT-
Instruction Manual
Do not attempt operation until you are familiar with all warnings, precautions, and procedures outlined within this
instruction sheet. Read carefully before operating. Retain these instructions for future reference.
WARNING:
This fixture is not factory sealed.
This fixture is designed to be used in a explosion proof environment.
Ensure periodic inspections to be sure that the fixture is still fully functional.
To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and maintained by a
qualified electrician only in accordance with all applicable electrical codes.
Be certain electrical power is OFF before and during installation and maintenance.
Luminaire must be connected to a wiring system with an equipment-grounding conductor.
Make sure the supply voltage is the same as the rated luminaire voltage.
The technical data indicated on the LED luminares are to be observed.
Changes of the design and modifications to the LED luminare are not permitted.
Observe the national electrical safety rules and regulations during installation.
Installing the EPLC2-EMG-HB-150LED-RT.
This EPLC2-EMG-HB-150LED-RTcomes preconfigured with a backup battery and two run configurations. The light can
be wired to accommodate Incoming Power while not emitting any visible light until the incoming power is stopped. IE:
Emergency Only Mode. However, the light also can be wired to provide visible light with or without incoming power. This
ensures that the light will operate in all conditions. IE: Backup Supported Mode
1. Emergency Only Mode Instructions –Wire the “Neutral”, “Hot”, and “Ground”wires normally. Leave the “Switch”
wire unconnected and terminated.
2. Backup Supported Mode –Wire the “Neutral”, “Hot”, and “Ground”wires normally. Wire the “Switch”wire in with
the “Hot”wire.
*For detailed instruction or clarification please call Larson Electronics at 1-800-369-6671.

EPLC2-EMG-HB-150LED-RT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
OPERATION
During normal operation, AC power is supplied to the AC ballast/driver through the backup micro inverter and the inverter
charges the battery. Connecting the inverter connector wires (red and white) enables the emergency circuit and supplies
power to the control/monitor circuit. The backup micro inverter detects AC input line voltage (120/277) and automatically
sets the output voltage during emergency mode.
When AC power fails, the backup micro inverter automatically switches to emergency mode, keeping the load illuminated
for a minimum of 90 minutes. When AC power is restored, the backup micro inverter returns to charging mode. The
backup micro inverter consists of a low-battery voltage disconnect which is reset when AC power is restored. The unit can
also detect an abnormal load condition (open or shorted load) during emergency mode operation and will protect the
inverter from damage.
MAINTENANCE
Although no routine maintenance is required to keep the backup micro inverter functional, it should be checked
periodically to ensure that it is working .The following schedule is recommended:
1. Visually inspect the charging indicator light monthly. It should be illuminated.
2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. The lam p
should operate at full illumination.
3. Conduct a 90-minute discharge test once a year. The lamp should operate at full illumination f or at
least 90 minutes.
!!!! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !!!!
REPLACEMENT PARTS
The EPLC2-EMG-HB-150LED-RTis designed to provide years of reliable lighting performance. Should the need
for replacement parts arise, please contact Larson Electronics at the contact information below.
Should further information not covered by these instructions be required, please contact Larson Electronics at
1-800-369-6671 or [e-mail] for further assistance.
Please visit LarsonElectronics.com for Warranty and Return information.