Larson Electronics EPL-EMG-LED-100W-RT User manual

EPL-EMG-LED-100W-RT
100W Explosion Proof Emergency LED Flood Light
Surface Mount - 14,000 Lumens - C1D1
Instruction Manual
Thank you for your purchase of the Larson Electronics EPL-EMG-LED-100W-RT explosion proof emergency LED flood
light.
WARNING
TO AVOID THE RISK OF FIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALL APPLICABLE
ELECTRICAL CODES.
TO AVOID ELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The Larson Electronics EPL-EMG-LED-100W-RT Explosion Proof Emergency LED Flood Light Fixture provides operators
with a powerful and energy efficient alternative to traditional hazardous location luminaries. Cree LED technology and
compact design makes this lamp an excellent replacement upgrade option for bulky and high maintenance cost older
fixtures. This unit features a remote mount battery backup for emergency operation.
Mounting
The Larson Electronics EPL-EMG-LED-100W-RT is designed for surface
mounting applications. The light fixture and emergency ballast are equipped
with U-brackets with a pre-drilled hole in the bottom for mounting to any flat,
sturdy surface capable of supporting the load. Secure the light and ballast in
the desired location with appropriate hardware. Mounting hardware is not
included, but is available from Larson Electronics if needed. Be sure ballast is
mounted near enough to supply power wires, and near enough to light to
complete wiring connections. Set desired vertical angle of the light fixture by
removing the rear Allen head screws on either side of the U-bracket attached
to light, tilt the light to desired angle, and replace screws to hold in place.
Power
Warning: Check product label for correct input voltage!
We strongly encourage a licensed electrician install this product, in all
locations, especially in outdoor areas where weatherproofing may be required.
Attach supply line wires to the appropriate light fixture wires as shown in
the applicable diagram 
Secure each pair of wires according to the diagram. Utilize a junction box or similar
device and take precautionary steps for weatherproofing all connections if installed in
a location where water may come in contact with the unit. Ensure the unit is properly
grounded and that wiring is done according to all local and national electrical/building
codes. If you are unfamiliar with these systems, or if you feel uncomfortable completing
this installation, stop and contact a licensed and qualified electrician to complete the
installation.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2

EPL-EMG-LED-100W-RT
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
Emergency Operation
This emergency LED light works, mounts, and is wired like our EPL-LED-100W-RT LED light fixtures. The main difference
is that we add a remote mounted battery backup unit that adds emergency light functionality to the fixture. This emergency
LED light will run at the standard UL suggested 90 minutes after power is lost at 2,625 lumens. The light recharges the
battery once electrical power is restored. Standard configuration includes a single emergency battery backup that is
automatically recharged and kept in a ready state.
MAINTENANCE
There are no serviceable parts inside the fixture. However, itis good practice to routinely clean and check the
fixture for proper function.
•Disconnectpower running to the lamp and be sure the fixture iscool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is notnecessary toopen the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affectthe life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of children
when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPL-EMG-LED-100W-RT is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.