Larson Electronics WAL-ML-2XM-3G User manual

WAL-ML-2XM-3G
Mini Light Tower
Instruction Manual
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
The Larson Electronics WAL-ML-2XM-3G Mini Light Tower with 3000VA Generator from Larson Electronics is an ideal
solution for operators who need a fully portable yet easy to operate light system capable of illuminating large areas.
Adjustable from 7 to 12 feet in height and equipped with a 3000VA generator and two 1000 watt metal halide lamps, this
unit will provide over 200,000 lumens of illumination for up to 6 hours on a single tank of fuel.
Uncrating
Unpack your new generator operated light tower by removing the plastic and cardboard that
surrounds the crate. Once the covers are removed, the crate will need to be disassembled so
you can remove the cart, head and mast (you will need a #2 square head drill bit and a drill to
do this). Once you have removed the wood framing you will be able to remove the generator
cart, light head, and mast.
Installing Light Mast
*Video available, see below installation steps for link
1. First, remove light head from shipping mast by loosening T-handle screw and lifting it off.
2. Remove shipping mast by removing the hardware holding it in place at the base.
3. Install light head onto top of light mast by slipping it over the top, and tightening the T-
handle screw to secure.
4. Place light mast in same location the shipping mast was removed from, with the winch
facing away from the generator. Secure using the hardware removed in step 2.
5. Mast is now assembled and ready for use.
**CAUTION: THIS UNIT IS HEAVY AND MAY REQUIRE 2 OR MORE PEOPLE TO UNPACK AND ASSEMBLE**
Installation Video: See video below. Make note of shipping mast mounting method. Install light mast in the same
manner. All you need to do is remove the shipping mast and install the light mast on the generator base. Get someone’s
assistance to help lift the mast to install it on the generator base. Be sure that the bottom hole on the lower part of the
mast lines up with the hole in the mounting plate on the generator base. Once lined up install the provided bolt, washers,
nuts and pin removed from the shipping mast.
NOTE: FOLLOW VIDEO ACCORDINGLY. SEE REVISED MOUNTING METHOD FOR MAST BELOW. A PIN IS
INSTALLED ON TOP OF BRACKET AND IN FRONT OF MAST.
Video Link:
https://www.youtube.com/watch?
v=xIWH3aMIKx4 PIN
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 4

WAL-ML-2XM-3G
Operation
The WAL-ML-2XM-3G mini light tower is a portable lighting system designed for stand alone operation and high mobility
while providing enough output to illuminate approximately 2 acres of area effectively. Simple position the the unit in a
level location by rolling it into place. The handlebar can be articulated if you remove the top pin in the base holding it
vertical. We suggest using wheel chocks to prevent unwanted movement.
Outriggers
Once the unit is in desired location, outriggers can now be deployed. For the rear outriggers, loosen the T-handle screws
on the underside of the unit, and pull outriggers outward until the flange stops at the T-handle screws. If you pull the
flange out completely, push it back in just past the screw and tighten T-handle to secure it in place. The T-handle screws
for the front are not installed, as they must be left out when moving the unit to allow full steering rotation. Pull outriggers
out to the same point as the rears, then install T-handle screws and tighten to secure. Next, loosen each T-handle screw
holding the legs up and allow them to drop into place against the ground or floor. Outriggers can be adjusted to level the
light tower itself before raising.
Mast Extension
Extend the mast by turning the winch handle clock wise. The mast can be elevated to any point desired as it has a brake
system on the winch that will hold it in position. Be sure mast is level before raising. Turn winch handle in the opposite
direction to lower mast. If mast is not level, it may not lower properly. Keep an eye on the winch cable and mast as you
lower it to ensure it is still moving down. If mast stops and cable has slack, turn winch clockwise again to put the tension
back on the cable and try lowering it again.
Do not overextend the mast past it's 12' max height, as this could cause damage to the cable or pulleys, and cause
the mast to come down in an uncontrolled manner causing damage or injury. There is an upstop bolt on the side of the
mast, be sure this stays in place close to the inner mast to prevent it from being overextended.
Generator
Pre-start checks:
•Check the generator for motor oil. Your generator will specify the correct oil and amount.
•Please check this before you start the generator. Failure to do so will damage the engine.
•Fill the generator up with fuel before trying to start it. We recommend 91 octane or better for optimal performance.
On top of the generator, there is a fuel gauge that will identify how much fuel is in the unit's reserves. To add fuel,
simply locate the gas cap on the top of the generator, remove the cap, ensure the fuel filter is in place and pour fuel
in. After fueling up the generator, replace the cap and secure it by rotating clockwise until you hear it click.
oNOTE: it is important to have the fuel filter in any time you wish to add fuel. This screen helps keep debris
out of the tank and keep your fuel clean.
•Before operation, ensure the STOP switch is in the STOP position.
To Start:
•Before start-up, ensure there is nothing connected to the generator in any of the receptacles. Generator should be
started and stopped with no load.
•Flip the STOP/RUN switch to the RUN position.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 4

WAL-ML-2XM-3G
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 3of 4
•Make sure the fuel petcock is in the ON position. For cold start, you'll also
want to make sure the yellow choke lever is moved into the choke position.
•Pull the ripcord to start the generator. Allow the generator to run
for a couple of minutes to allow revs and voltage to stabilize
before connecting anything to it.
NOTE: If the engine fails to keep running, try pulling the starter
cord one more time.
•Once generator is warmed up and revs have stabilized, you may
connect the lights to the receptacle on the generator. Light head is
fitted with a twist lock plug that must be turned in the receptacle to
secure it.
•To turn the generator off, flip the STOP/RUN switch to the STOP position.
Maintenance
•Check the oil regularly, as shown above, to verify there is enough in the engine
before running.
•Check the air filter regularly and replace as necessary. Air filter is located in the
black casing at one end of the generator, as shown in the picture to the right.

WAL-ML-2XM-3G
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 4of 4
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The WAL-ML-2XM-3G is designed to provide years of reliable performance. Should the need for replacement parts arise,
please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.