Larson Electronics WAL-TL-3XTL-C-SOL-100C User manual

WAL-TL-3XTL-C-SOL-100C
Solar Powered LED Signal Stack Light
Red, Yellow, Green - 100' 12/4 SOOW Cord
Instruction Manual
Thank you for your purchase of the Larson Electronics WAL-TL-3XTL-C-SOL-100C Solar Powered LED Signal Stack Light.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
The WAL-TL-3XTL-C-SOL-100C Solar Powered LED Signal Stack Light from Larson Electronics is designed for routing
traffic in industrial refueling stations and safety notifications. This two-watt unit emits red, amber and green colors,
while operating on 24V AC/DC. The LED stack light is equipped with a waterproof solar panel and 100` of 12/4 SOOW
cable between the panel and the light fixture.
INSTALLATION
MOUNTING SOLAR PANEL
This solar panel includes a permanent mounting system that allows for
mounting to square/round poles or flat surfaces such as a wall or post
shown in figure below.
Position the solar panel in a location that receives the maximum amount of
sunlight throughout the day. This may need adjusted depending on the
season. With pole mounting, loosen the adjustment bolts to fit solar panel
onto pole. Once mounted, tighten bolts snug to secure panel to pole. For
surface mounting, remove additional plate and use the existing mounting
holes to mount directly to surface.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
MOUNTING STACK LIGHT
We strongly encourage a licensed electrician install this product,
in all locations, especially in outdoor areas where weatherproofing
may be required. Follow all applicable building and electrical code
when installing.
The stack light is designed to be mounted to the top of a threaded pipe
using the coupler on the bottom of the light. Feed the wiring through
the pipe you are mounting the light to, and thread the coupler onto the
pipe. Complete wiring connections utilizing the provided connectors,
each wire is labeled with it's corresponding connection. Once
connections are complete, thread the light onto the top of the coupler.
Installation is now complete.

WAL-TL-3XTL-C-SOL-100C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
HOW SOLAR LIGHT WORKS
Solar light must be placed outdoors. The solar panel collects and converts sunlight into DC power while the pre-installed rechargeable
batterystoresthe energy to power the light at night.
Solar light illumination time
It depends on the seasonal sunlight availability in your geographical area under certain weather conditions. Stronger or longer sunlight
hours enable batteries to store more energy which provides more lighting hours. On the contrary, weaker or shorter sunlight hours
reduce the lighting hours and its brightness as well.
Solar panel mounting locations
Solar panel must be placed outdoor at a location with its solar panel receiving direct sunlight at least five hours each day. Shadowed
locations will not allow batteryto be fully charged and will reduce both the brightness of the light and the lighting hours. Precautions
(prior to first time use)
1. To maximize battery capacity, the solar panel should be fully charged by direct sunlight for five hours before initial use.
2. Under extremely cold temperatures, the batteries may not charge fully. In such cases, the Solar Lights may not stay
illuminated as long.
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture iscool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens and panel as needed.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The WAL-TL-3XTL-C-SOL-100C is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.