Larson Electronics GAU-LTL-500W-LED-IR User manual

GAU-LTL-500W-LED-IR
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
250W High Intensity Infrared LED Light
120-277V AC - IP67 Waterproof
Instruction Manual
Thank you for your purchase of the Larson Electronics GAU-LTL-500W-LED-IR.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE GAU-LTL-500W-LED-IR MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.
Infrared Warning
INFRARED LIGHT MAY CAUSE DAMAGE TO EYES IN VERY INTENSE CONCENTRATIONS.
RISK OFEYE DAMAGE AT SHORT DISTANCES. TURN LIGHT SOURCE OFF BEFORE SERVICING.
The GAU-LTL-500W-LED-IR High Mast LED Flood Light emits non-visible infrared beams in outdoor work sites. This 250-
watt infrared LED lamp provides operators with a rugged and powerful LED alternative to traditional infrared fixtures,
consumes little power and can withstand rugged use and abusive conditions. The infrared LED unit is offered in 750 nm,
850 nm or 940 nm infrared band configurations.
MOUNTING
Each unit is equipped with a back mount trunnion style mounting bracket that allows the light to be attached to flat surfaces
and adjusted through 160° of vertical movement. To adjust the unit after mounting, the user simply loosens the set screws
located on either side of the unit, moves it into the desired position, then re-tightens the screws. The base of the mounting
trunnion is equipped with several machined slots which allow users to utilize existing mounting holes and slide the unit for
precise mount positioning.

GAU-LTL-500W-LED-IR
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
INSTALLATION
We strongly recommend only a licensed electrician install this product. Make sure
power is disconnected prior to installing. Fixture must be mounted to a surface that
can structurally support the load.
The fixture will be supplied with a cord cap/whip already affixed to the housing.
Mount following the steps below:
1. Turn off power at electrical panel.
2. Mount light by its trunnion mount to a flat surface. Utilize bolts through predrilled
mounting holes.
3. Adjust lamp vertically by loosening hex bolts on either side.
4. Swing lamp into final position and tighten any loose bolts.
5. Wire the whip/power cord to existing power source. Follow proper steps to
weatherproof electrical connections as necessary.
6. Turn power on.
This light is “instant-on” and will illuminate once power is supplied to the unit.
Double check voltage prior to plugging in!
This light is “instant-on” and will illuminate once power is supplied to the unit. Wire Diagrams
(Match wire colors to unit received.)
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER
INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT [email protected] OR BY PHONE
AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
Voltage: 120-277V AC
*ACTUAL STYLE MAY VARY
ADJUTMENT BOLTS
MAINTENANCE
Caution: To avoidpersonal injury,disconnect power to the light and allow the unit to cool downbeforeperforming maintenance.
Warning:No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will voidthe warranty.
1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine checks to be made on a
yearly basis. Frequency of use and environment shoulddetermine this. It is recommendedto follow an Electrical Preventive
Maintenance Program as described in NFPA 70B: Recommendedpractice for Electrical Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance. Clean the lens with a
damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or contamination (i.e.excessive
dust build-up). Clean with a non-abrasive clothif needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPP-20A-25P is designed to provide years of reliable performance. Should the need for replacement parts arise,
please contact Larson Electronics.