Larson Electronics LEDWP-250E-DLC-5000K Manual

LEDWP-250E-DLC-5000K
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
LEDWP-250E-DLC-5000K Instruction Guide
25 Watt Low Profile LED Wall Pack Light
Thank you for your purchase of the Larson Electronics LEDWP-250E-DLC-5000K Wall Pack Light. Please
follow the steps below in order to install, operate and maintain this product.
MOUNTING
The LED wall pack includes all necessary hardware for installing the mounting bracket, and cord grip. Follow
the guideline below to properly assemble and install the unit.
The wall pack light includes the LED light, trunnion mount, and hardware for installing the center cord grip.
Some models may omit hardware depending on selected options.
Ambient Temperature Range: -25°C to +60°
1. Begin by choosing a location to install the fixture. This LED wall pack is IP68 waterproof, vapor proof,
and built to resist the damaging effects of an outdoor environment. This fixture should not be used in areas
with no ventilation or extreme ambient temperatures.
2. Affix the mount to your chosen surface. There are 3 predrilled holes on the trunnion bracket. 2 for
mounting and 1 for the cord grip. These can be used any way suitable for the location. Plan a way for
wiring to connect such as using a separate junction box and utilize the cord grip where necessary.
3. Attach lamp.The trunnion mount can be attached to the lamp in two locations, the lower area or middle
area on the back of the wall pack. Use the included ( 2 screws ❶) and ( 2 lock washers ❷) for
attaching the mount as shown in the diagram on page 2. The fixture can be placed in any direction.
WIRING
We strongly encourage a licensed electrician install this product, especially in outdoor locations where
weatherproofing may be required. Universal voltage driver permits operation at 110V - 277V AC, 50 or 60Hz
except those factory ordered with low voltage 11V to 25V AC/DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light
fixture wires as shown in the diagram

Secure each pair with a wire nut according to the
diagram. Utilize a junction box or similar device and
take precautionary steps for weatherproofing all
connections if installed in a location where water may
come in contact with the unit. Ensure the unit is
properly grounded.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LEDWP-600E MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND
ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.

LEDWP-250E-DLC-5000K
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
ASSEMBLY
Use the table below for assembling the hardware.
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good
practice to routinely clean and check the fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture
is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the
LED’s.
TROUBLESHOOTING
Refer to the guide below or contact the manufacturer if the fixture does not function properly.
Is the correct line voltage being supplied to the fixture?
Is the fixture properly grounded?
Make sure installed power switches, photocells, etc. are functioning properly.
These instructions may not cover all details or variations of this product for your equipment or installation
requirements. Should further information not covered by these instructions be required, please contact Larson
Electronics at 1-800-369-6671 for further assistance.
CORD GRIP
MOUNT SCREW
Not
Applicable