Larson Electronics AML-LED-WP40-M-22C Manual

AML-LED-WP40-M-22C
Larson Electronics, LLC
Phone: [phone]
Fax: [phone]
www.larsonelectronics.com
1 of 2
AML-LED-WP40-M-22C Instruction Guide
40 Watt Automotive Mechanics' Work Light
Thank you for your purchase of the Larson Electronics AML-LED-WP40-M-22C Automotive Mechanics'
LED Work Light. Please follow the steps below in order to install, operate,and maintain this product.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE AML-LED-WP40-M-22C MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE ANDALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLYENCOURAGE THAT ONLYA LICENSED ELECTRICIAN INSTALL,OPERATE,AND
MAINTAIN THIS PRODUCT. IF YOU ARE NOT QUALIFIED OR ARE UNFAMILIAR WITH ANY ASPECTOF THIS
INSTRUCTION SHEET, CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLEPARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK – DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY – FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN – ALLOW FIXTURE TO COOL BEFORE SERVICING.
MOUNTING
The work light includes the LED light,cord w/ cord cap, trunnion mount w/ magnet, and glareshield.
Ambient Temperature Range: -25°C to +60°C
1. Select a location to install the fixture. This LED work light is IP68 waterproof, vapor proof,and built
to resistthe damaging effects of an outdoor environment. This fixtureshould not be used in areas with
no ventilation or extreme ambient temperatures.
2. Affix the mount to your chosen metal surface. A 200 lb grip magnetic base allows the unit to be
mounted to any metal surface capable of holding itsweight. Run power cordto the appropriate
receptacle with the CORRECT VOLTAGE.
3. Lamp Adjustment. The trunnion mount can be attached to the lampin two locations, the lower area or
middle area on the back of the wall pack. Use the ( 2 screws ❶) and ( 2 lock washers ❷) for
repositioning the mount as shown in the diagram on page 2. The fixturecan be placed in any direction.
WIRING
We strongly encourage a licensed electrician install this product, especially in outdoor locations where
weatherproofing may be required. Universal voltage driver permitsoperation at 100 V - 277 V AC, 50 or 60
Hz except those factoryordered with low voltage 11 V to 25 V AC/DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light
fixture wires as shown in the diagram 
This unit comes pre-wired from factory with the
selected cord length and cord cap. Take precautionary
steps for weatherproofing all connections if installed in
a location where water may come in contact with the
unit. Ensure the unit is properly grounded.
200 lb Magnet

AML-LED-WP40-M-22C
Larson Electronics, LLC
Phone: [phone]
Fax: [phone]
www.larsonelectronics.com
2 of 2
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
• Disconnect power running to the lamp and be sure the fixture is cool to the touch.
• Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessaryto open the fixture and clean or touch the LEDs.
TROUBLESHOOTING
Refer to the guide below or contact the manufacturer if the fixture does not function properly.
Is the correct line voltage being supplied to the fixture?
Is the fixture properly grounded?
Make sure installed power switches, photocells, etc. are functioning properly.
These instructions may not cover all details or variations of this product for your equipment or installation
requirements. Should further information not covered by these instructions be required, please contact Larson
Electronics at 1-800-369-6671 for further assistance.