Larson Electronics WAL-QP-2X500LTL-LED-100 User manual

WAL-QPW-4XWP60E-25C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 3
The WAL-QP-2X500LTL-LED-100 Quadpod Mounted LED Work Area Light from Larson Electronics produces
120,000 lumens and is equipped with 100 of SOOW cable. This LED light tower is designed for portability and
durable operation and ideal for use in demanding conditions. Dual 500 Watt LED light heads cover up to
70,000 square footage.
WARNING: Read all instructions carefully
SAVE THESE INSTRUCTIONS
CAUTION: RISK OF ELECTRICAL SHOCK
Do not use with extension cord near water or
where water may accumulate.
Keep plugs and receptacles dry.
For use only on GFCI protected circuits.
Risk of burns, do not operate without lens.
Lighted lamp is hot. Keep away from
combustibles.
WARNING RISK OF FIRE, ELECTRIC SHOCK,
EXPOSURE.
TO EXCESSIVE UV RADIATION OR INJURY TO
PERSONS
Unplug and allow cooling before replacing bulb.
Light gets HOT quickly
Do not touch hot lens guard or enclosure.
Do not remain in light if skin feels warm.
Do not look directly at lighted lamp.
Keep lamp away from materials that may bum.
Do not operate the lamp with missing or
damaged guard, lens, or cord.
QUADPOD ASSEMBLY
The quadpod assembly consists of 3 parts:
1. Light head
2. Pole w/Legs
3. Wheel base
To assemble quadpod, begin by placing the legs over the wheel base. Tighten bolt to secure the
wheels. The quadpod can now be rolled around on its wheels. Ensure the legs are folded up before
tilting quadpod to maneuver.
WARNING: Use caution before tilting quadpod with a heavy load. For heavy loads, it is
recommended to remove the light head prior to transporting via wheel base! Failure to do so may
cause serious injury or death. Larson Electronics shall not be held liable for injuries caused by
misuse.
1. Place tower in desired location that is flat and able to support the quadpod without falling over.
2. Loosen lower hand screw and lower legs until firmly stabilizing quadpod.
3. Tighten hand screw to secure legs.
4. With help, place the light head over top pole and tighten top hand screw.
Lightweight lamps can be attached by tilting quadpod toward the ground with the legs up. Attach light
head to pole, tighten hand screw and tilt back to its vertical position. DO NOT tilt quadpod while
extended to max height. It is recommended to have another person hold the quadpod while tilting
vertically.
240W General Area LED Crank Up Light Tower
Adjustable 12' to 20' - (4) LED Lamps - 20' 16/3 SOOW Cord
Instruction Manual

WAL-QPW-4XWP60E-25C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 3
For heavy weight lamps, use a ladder and extra help for attaching light head to pole.
Double check that all hand screws are tight before continuing use of the light tower.
EXTENDING
LOWERING
The quadpod mount light tower can be disassembled for storage or transporting. Unplug light from
power source and remove light head following previous steps for attaching.
Once the light head has been removed, loosen hand screw for legs and fold them up. Wheel to
desired location or remove from wheel base for complete disassembly.
THE LENS AND CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, SCRATCHES OR ANY
SEVERE ABRASIONS, AND IF ANY ARE FOUND, THE PARTS MUST BE REPLACED BEFORE
RESUMING USE OF THE LIGHT TOWER.
LAMP ADJUSTMENT
1. Adjust lamp vertically by loosening bolts on either side.
2. Swing lamp into final position and tighten any loose bolts.
ADJUTMENT BOLTS
To extend the light higher, simply turn the hand crank winch until the light reaches the desired height. There is a stop bolt
installed to keep the light from extending past it's maximum height. Always consider the conditions in which you are
raising the light, such as wind and precipitation. Light should not be operated in high winds or rain, as damage or injury
could occur.
WARNING: Do not operate light in high winds as it could topple and cause damage or injury. Larson Electronics
shall not be held liable for any injury caused by misuse.
To lower the light, simply turn the hand crank winch in the opposite direction. Keep an eye on the cable as you lower and
be sure it maintains tension. If the mast stops lowering and cable has slack, you will need to raise the mast again to
remove slack before lowering. Stop once the mast reaches lowest point, leaving no slack in the cable.

WAL-QPW-4XWP60E-25C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 3
WIRING (see attached wiring diagram)
This unit comes preconfigured with 20 feet
SOOW Cord and plug. Once deployed, plug cord
cap into compatible receptacle with Voltage
indicated on nameplate.
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool
down before performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens
will void the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend
routine checks to be made on a yearly basis. Frequency of use and environment should
determine this. It is recommended to follow an Electrical Preventive Maintenance Program
as described in NFPA 70B: Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric
performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use
mild soap or a liquid cleaner.
3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions
or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if
needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
REPLACEMENT PARTS
The WAL-QPW-4XWP60E-25C is designed to provide years of reliable performance. Should the
need for replacement parts arise, please contact Larson Electronics.
WARNING: CHECK NAMEPLATE
FOR PROPER VOLTAGE. DAMAGE
FROM IMPROPER VOLTAGE WILL
VOID WARRANTY.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.