Larson Electronics EPL-16C-1MLED-300 User manual

EPL-16C-1MLED-300
Explosion Proof LED Tank Light
21,000 Lumens LED - Wheelbarrow Cart - 300' Cord - C1D1 C2D1
Instruction Manual
Thank you for your purchase of the Larson Electronics EPL-16C-1MLED-300 Explosion Proof LED Tank Light.
WARNING
TO AVOID THE RISK OFFIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALL
APPLICABLE ELECTRICAL CODES.
TO AVOID ELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The EPL-16C-1MLED-300 Explosion Proof Portable Tank Light from Larson Electronics is rated Class 1 Division 1-2
Groups C&D and Class II Division 1-2 and uses Cree LEDs to produce 21,000 lumens of light while drawing only 150 watts.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
The light fixture on this wheelbarrow cart is factory sealed.
CART OPERATION
The wheelbarrow cart assembly consists of 2 parts:
1. Light head
2. Wheelbarrow cart base
To assemble cart, insert light head over center hole
of wheelbarrow cart and tighten hand screw. The
wheelbarrow cart is now ready for use.
Tilt cart using both handles and maneuver like a
wheelbarrow. Simply roll entire assembly toa new
location once assembled. Make sure light head is
secure prior to maneuvering cart.
This portable LED cart light has a removable light
head measuring 16 inches in diameter which allows
the unit to fit through the standard sized manholes or
entry passages commonly found in the petrochemical and marine industries. Often simply referred to as a
“tank light”, this unit is considered universal due to its ability to be passed through any conventional manhole
such as those found in petrochemical containers and ship storage tanks.
WARNING: Be sure all hand screws aretight before transporting! Use caution when maneuvering near inclines
or drop offs.
 To adjust light head vertically, loosen hand screws on either side. Once desired angle is achieved,
tighten both hand screws to secure light in its place. Loosen the single hand screw holding light head to rotate
horizontally. Be sure all hand screws are tight before transporting!

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
EPL-16C-1MLED-300
This unit comes pre-wired from factory with the selected cord cap. Take precautionary steps for
weatherproofing all connections if installed in a location where water may come in contact with the unit. All
outdoor installations and indoor installations near a wet location require the use of a GFCI device for safety,
according to the National Electrical Code® (NEC). Ensure the unit is properly grounded.
Position device near work area for operation. Run cable to nearby power source. Insert and twist-lock
explosion-proof plug into a compatible receptacle within the hazardous environment. See plug operation
below.
WARNING: check nameplate for proper voltage. Damage from improper voltage may void warranty.
PLUG OPERATION
Electrical connection between plug and compatible receptacle is accomplished after plug fully inserts into
receptacle and is rotated clockwise.
1. Lift receptacle door and locate polarization on mating plug pin and receptacle face. Insert plug straight all
the way into receptacle until it cannot go further.
2. Rotate plug clockwise limit (37º), this closes internal contacts and completes circuit. This also
mechanically locks plug into receptacle so it cannot be pulled out.
3. To remove plug, push plug inward and turn to counterclockwise, pull plug straight out.
MAINTENANCE
Caution:To avoid personal injury,disconnect powerto the light and allow theunit to cool down before
performing maintenance.
Warning: No user serviceable parts inside of fixture.Risk of electricshock.Removalof the lenswill void any
warranty.
1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine
checks to be made on a yearly basis. Frequency of use and environment shoulddetermine this. It is
recommendedto follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommendedpractice for Electrical Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance.
Clean the lens with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e.excessivedust build-up). Clean with a non-abrasive clothif needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPL-16C-1MLED-300 is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.