Lauda LRZ 926 User manual

Interface module LRZ 926
RS 232/485 Advanced module
Operation manual
V1R13 Read this manual prior to performing any task!

Translation of the original operation manual
Manufacturer:
LAUDA DR. R. WOBSER GMBH & CO. KG
Laudaplatz 1
97922 Lauda-Königshofen
Germany
Telephone: [phone]
Fax: [phone]
E-mail: [email protected]
Internet: https://www.lauda.de
Q4DA-E_13-021, 1, en_US 05/09/2022 ©LAUDA 2022
V1Interface module LRZ 9262 / 43

Table of contents
1 General................................................................................................................................................................................... 5
1.1 Intended use................................................................................................................................................................... 5
1.2 Compatibility.................................................................................................................................................................. 6
1.3 Technical changes.......................................................................................................................................................... 6
1.4 Warranty conditions...................................................................................................................................................... 6
1.5 Copyright....................................................................................................................................................................... 6
1.6 Contact LAUDA........................................................................................................................................................... 7
2 Safety..................................................................................................................................................................................... 8
2.1 General safety information and warnings................................................................................................................... 8
2.2 Information about the interface module.................................................................................................................... 9
2.3 Personnel qualification.................................................................................................................................................. 9
3 Unpacking............................................................................................................................................................................ 10
4 Device description................................................................................................................................................................ 11
4.1 Purpose.......................................................................................................................................................................... 11
4.2 Structure........................................................................................................................................................................ 11
5 Before starting up................................................................................................................................................................ 12
5.1 Installing the interface module................................................................................................................................... 12
5.2 Using the module box.................................................................................................................................................. 14
6 Commissioning..................................................................................................................................................................... 15
6.1 Contact assignment..................................................................................................................................................... 15
6.1.1 Contact assignment RS 232................................................................................................................... 15
6.1.2 Contact assignment RS 485................................................................................................................... 17
6.2 Software update........................................................................................................................................................... 17
7 Operation............................................................................................................................................................................. 18
7.1 Menu structure............................................................................................................................................................ 18
7.2 Interface functions....................................................................................................................................................... 18
7.2.1 General Information................................................................................................................................. 18
7.2.2 Operating rights....................................................................................................................................... 20
7.2.3 Communication monitoring................................................................................................................... 20
7.2.4 Read commands........................................................................................................................................ 21
7.2.5 Write commands...................................................................................................................................... 26
7.2.6 Availability of the interface functions.................................................................................................... 29
7.2.7 Error messages......................................................................................................................................... 32
7.3 Control and automation software............................................................................................................................. 34
8 Maintenance........................................................................................................................................................................ 35
9 Faults.................................................................................................................................................................................... 36
9.1 Alarm............................................................................................................................................................................ 36
V1 Interface module LRZ 926 3 / 43

9.2 Error.............................................................................................................................................................................. 36
9.3 Warning........................................................................................................................................................................ 37
10 Decommissioning................................................................................................................................................................ 38
11 Disposal................................................................................................................................................................................ 39
12 Accessories.......................................................................................................................................................................... 40
13 Technical data....................................................................................................................................................................... 41
14 Index..................................................................................................................................................................................... 42
V1Interface module LRZ 9264 / 43

1 General
Many types of LAUDA constant temperature equipment have vacant
module slots for installing additional interfaces. The number, size and
arrangement of the module slots vary depending on the device and are
described in the operating manual accompanying the constant temperature
equipment. Two additional module slots available as accessories can be fitted
to a LiBus module box, which is then connected as an external casing to the
LiBus interface on the constant temperature equipment.
This operating manual describes how to install and configure the RS
232/485 interface module (catalog no. LRZ 926).
The RS 232/485 interface is designed for activating constant temperature
equipment via the LAUDA command set. The interface functions provided
for this purpose are described in the chapters Write commands and Read
commands.
1.1 Intended use
The interface module can only be operated as intended and under the
conditions specified in this operating manual.
The interface module is an accessory that increases the connections options
of LAUDA constant temperature equipment. It may only be installed in con-
stant temperature equipment that supports the interface provided. Refer to
the chapter "Compatibility” in this operating manual for a list of compatible
product lines.
Operation of the interface module is also permitted in combination with the
LiBus module box (LAUDA catalog no. LCZ 9727). This operating manual
also contains a description of how to install and connect up the module box.
Operation after incomplete assembly
Operation on incompatible constant temperature equipment
Operation using cables or connections that are defective or do not
confirm to standards
Reasonably foreseeable improper use
V1 Interface module LRZ 926 5 / 43

1.2 Compatibility
The interface module is available as an accessory for the following LAUDA
product lines:
Integral IN
PRO
Variocool
Variocool NRTL
No operation of interfaces of the same type
Only one RS 232/485 type interface can be used for each item
of constant temperature equipment. This applies irrespective of the
interface operating mode.
No operation of dierent interfaces
Combining the RS 232/485 interface with a Profibus, Profinet,
or CAN interface is not permitted. These interfaces cannot be
combined with one another.
1.3 Technical changes
All technical modifications are prohibited without the written consent of the
manufacturer. Damage resulting from a failure to observe this condition will
void all warranty claims.
However, LAUDA reserves the right to make general technical modifica-
tions.
1.4 Warranty conditions
LAUDA grants a standard warranty of one year.
1.5 Copyright
This operating manual was written in German, checked and approved. If
the content of other language editions deviates from the German edition,
the information in the German edition shall take precedence. If you notice
any discrepancies in the content, please contact LAUDA Service, see
ÄChapter 1.6 “Contact LAUDA” on page 7.
Company and product names mentioned in the operating manual are usually
registered trademarks of the respective companies and are therefore subject
to brand and patent protection. Some of the images used may also show
accessories that are not included in the delivery.
All rights reserved, including those relating to technical modifications and
translations. This operating manual or parts thereof may not be modified,
translated or used in any other capacity without the written consent of
LAUDA. Violation of this may obligate the violator to the payment of dam-
ages. Other claims reserved.
V1
Interface module LRZ 9266 / 43

1.6 Contact LAUDA
Contact the LAUDA Service department in the following cases:
Troubleshooting
Technical questions
Ordering accessories and spare parts
Please contact our sales department for questions relating to your specific
application.
Contact information
LAUDA Service
Phone: [phone]
Fax: [phone]
Email: [email protected]
V1 Interface module LRZ 926 7 / 43

2 Safety
2.1 General safety information and warnings
Read this operating manual carefully before use.
Keep the operating manual in a place within easy reach of the interface
module.
This operating manual is part of the interface module. If the interface
module is passed on, the operating manual must be kept with it.
This operating manual is applicable in combination with the operating
manual of the constant temperature equipment in which the interface
module is installed.
Manuals for LAUDA products are available for download on the
LAUDA website: https://www.lauda.de
The warnings and safety instructions in this operating manual must be
observed without fail.
There are also certain requirements for personnel, see ÄChapter 2.3
“Personnel qualification” on page 9.
Warning signs Type of danger
Warning – danger zone.
Signal word Meaning
DANGER! This combination of symbol and
signal word indicates an imminently
dangerous situation that will result
in death or serious injury if it is not
avoided.
WARNING! This combination of symbol and
signal word indicates a potentially
dangerous situation that can result
in death or serious injury if it is not
avoided.
NOTICE! This combination of symbol and
signal word indicates a poten-
tially dangerous situation that can
result in material and environmental
damage if it is not avoided.
Structure of warnings
V1Interface module LRZ 9268 / 43

2.2 Information about the interface module
Always disconnect the constant temperature equipment from the power
supply before installing the interface module or connecting interfaces.
Always take the recommended safety measures against electrostatic
discharge before handling interface modules.
Avoid touching the circuit board with metallic tools.
Do not start up the constant temperature equipment before installation
of the interface module is complete.
Store any unused interface modules in their packaging in accordance
with the specified ambient conditions.
Use only suitable cables of sucient length for cable connections.
Make sure that the protective screen on the cables and connec-
tors complies with EMC regulations. LAUDA recommends using pre-
assembled cables.
Always lay cables correctly so that they do not pose a tripping hazard.
Secure the laid cables and make sure that they cannot be damaged
during operation.
Check the condition of the cables and interfaces prior to each opera-
tion.
Immediately clean any soiled parts, in particular unused interfaces.
Make sure that the signals transmitted via the interface correspond to
the permitted operating parameters of the interface module.
2.3 Personnel qualification
Only specialized personnel are permitted to install interfaces modules. Spe-
cialized personnel are personnel whose education, knowledge, and experi-
ence qualify them to assess the function and risks associated with the device
and its use.
Specialized personnel
V1 Interface module LRZ 926 9 / 43

3 Unpacking
DANGER!
Transport damage
Electric shock
Closely inspect the device for transport damage prior to
commissioning!
Never operate a device that has sustained transport
damage!
NOTICE!
Electrostatic discharge
Material damage
Always observe safety measures against electrostatic dis-
charge.
Please observe the following installation sequence:
1. Remove the interface module from its packaging.
2. If you want to store the interface module at the installation location,
use the outer packaging. This packaging is protected against static
charging.
3. After installing the equipment, dispose of the packaging materials in
line with environmental regulations, see Ä“Packaging” on page 39.
If you discover any damage on the interface module, contact
LAUDA Service immediately, see ÄChapter 1.6 “Contact
LAUDA” on page 7.
V1Interface module LRZ 92610 / 43