Legacy Deep Impact User manual

2
Registration
3. Owners Record
4. Warranty Information
5. The Cabinetry / Our Commitment
Setup
6. Unpacking Your Speakers
7. Speaker Placement / Installation
9. Hook up Cables
11. Unit Connections
15. Fine Tuning
Technology
17. Designer’s Note
19. Specifications
20. Troubleshooting

3
The model and serial numbers are located on the rear of the unit. Record
these numbers in the spaces provided below. Refer to them when calling
upon your dealer regarding this product.
Model No. _______________________________
Serial No. _______________________________
Date of purchase: _________________________
Thank you for selecting a Legacy Loudspeaker System. These hand-
crafted instruments will provide you with many years of listening
enjoyment. Please take a few moments to read this brief manual to insure
maximum benefit from your speaker system.

4
Ten Year Limited Cabinetry Warranty
Five Year Limited Electronics Warranty
Legacy Audio, Inc. extends to the original owner coverage of defects in
materials and workmanship for a period of 90 days from the date of
purchase. To extend this warranty to 10 years for cabinetry and 5 years
for the electronics, please fill out the enclosed warranty card and return to
Legacy Audio.
This warranty does not include:
a) Damage in shipment.
b) Damage caused by accidental or intentional misuse or abuse.
c) Units not registered with Legacy Audio.
d) Damage resulting from unauthorized modifications or repairs.
Liability is limited to the repair or replacement, at our option, of any
defective component and shall not include property or consequential
damages which may result from the failure of this product. You will void
warranty if the cabinet is opened without factory authorization.

5
Handcrafted
Beneath the surface of Marquis’s elegant exterior lies rigid MDF
construction. Interlocking joinery maximizes the strength of the cabinet
parts. Polyester fiberfill is selected for internal damping. A sharp rap on
the enclosure will leave you with little more than bruised knuckles.
Each cabinet is impeccably finished on all exposed surfaces with select
veneers. The exquisite finish is hand-rubbed several times to assure a
patina at home with the most elegant decor.
Our Commitment
A great deal of forethought, love and satisfaction is instilled in each piece
of Legacy workmanship. We take pride in getting to know many of our
customers on a first name basis.
Your purchase of this product is backed by the renowned “Legacy
Satisfaction Guarantee”. We continue to stand behind it with a solid ten
year warranty, more than twice the industry standard.

6
Your new subwoofer has been very carefully packaged to insure that it
travels to you safely. Each subwoofer is protected by a double-wall outer
carton with heavy V-board corner protectors. Molded foam end caps are
used to protect the elegant cabinetry, and a plastic liner is provided as
waterproofing. Please save this packing for future transportation. If cartons
become damaged or misplaced, new ones can be purchased from Legacy
Audio.

7
Since the human ear is rather poor at localizing radiation frequencies
below 125 Hz, good results may be obtained in a variety of room
placements. Careful adjustment of the convenient front panel controls will
lead to seamless transition.
Low frequency reinforcement occurs whenever woofers are placed near
room boundaries. The distance from the walls, floor and ceiling
correspond to the wavelengths of the frequencies, which will reflect in
phase and thus reinforce bass output. Therefore, the actual dimensions of
your listening room play a definite role in what ultimately arrives at your
ear. In fact, rooms tend to have their own set of favored frequencies.
We can calculate what the most strongly reinforced frequencies in a room
will be by the formula shown below:
Resonant Frequency = (1130 ft/sec) / (ft. between boundaries x 2)
For example, a room with an 8 ft. ceiling height has a strong resonance at:
(1130 ft/sec.) / (8 ft. x 2) = 71 Hz.

8
Now, while such reinforcement might actually be beneficial at very low
frequencies, excessive excitation can cause “overhang” or a droning effect
at mid-bass frequencies. A way to minimize excitation of these
resonances is to place your subwoofer asymmetrically relative to room
boundaries. For instance, if the subwoofer is 2 ft from one corner wall,
then place it 1.5 ft to 3 ft from the other.
Placing the subwoofer in a corner will reduce the radiation angle and thus
increase efficiency. It will also excite the maximum number of room modes
and decrease distortion.
A best case scenario is to actually use two subwoofers, one to each side
of the listener. The subs should be placed 90° out of phase with each
other. This improves spaciousness and bass uniformity, with a reduction in
room level peaks.

9
The ideal conductor would have negligible resistance, inductance and
capacitance. The table below shows how a few actual speaker cables
measure up.
Cable Ωs/ft pF/ft µH/ft
12 ga. 0.0033 24 0.21
14 ga. 0.0048 17 0.13
16 ga. 0.0079 16 0.18
18 ga. 0.0128 28 0.21
Capacitance is considered insignificant in each cable because its effect is
well out of the audio bandwidth; inductance can be decreased (at the
expense of increased capacitance) by keeping the conductor pair closely
spaced.
How long would a cable have to be before inductance effects would
impinge on the audio spectrum? Approximately 300 feet of 12 gauge
would be required to establish a corner frequency of 20 kHz with an 8
Ohm loudspeaker. As you see, inductance is not a problem for most of us.

10
What about phase shift due to frequency dependent travel times down the
speaker cable? Measurements show that 100 Hz waves will be delayed
about 20 billionths of a second behind 10 kHz waves when traveling to the
end of a 10 foot speaker cable. Since the cilia of the ear requires 25,000
times longer than this just to transmit phase information, phase shifting is
obviously not the primary concern when considering speaker cables.
What about resistance? Finally we are getting somewhere.
Resistance is the controlling factor of the amplifier/loudspeaker interface.
Excessive resistance can cause major shifts of speaker crossover
frequencies. The lower the impedance of the loudspeaker, the greater the
effects of series resistance. A 20 foot run of 18 gauge cable can cause up
to 10% deviations of crossover center frequencies. That same 20 feet can
un-damp your damping factor and reduce your systems’ output by one-
half decibel.
In summary, there are no perfect cables. The best way to approximate the
ideal would be to keep loudspeaker leads as short as is practical.