LEGRAND UTP-Fiber1G-USB User manual

UTP-Fiber1G-USB QSG 1
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
UTP-to-Fiber Media Converter
Thank you for purchasing the UTP-Fiber1G-USB, a 1G Fiber Converter with Power over USB.
Package Contents
•1G Fiber-to-UTP Converter with Power over USB
QSRule
Product Features
•Single-mode and multi-mode fiber support
•Distance up to 10km for single-mode fiber and up to 800m for multi-mode fiber
•Link Fault Pass-Through (LFP) support
•Auto dust cover
•Auto crossing to simplify cabling (MDI/MDIX)
•Individual LEDs to indicate power and communication status
QSRule
LED Panel
LED Label
Color
Status
Meaning
Power
Green
On
Module On
No light
Off
Module Off
Link/ACT
Green
On
1000 Mbps
Green Blinking
On
Activity
No light
Off
Disconnected
Fiber
Blue
On
Connected
No light
Off
Disconnected
QSRule
QUICK SETUP GUIDE

UTP-Fiber1G-USB QSG 2
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
LED Operation for Link Fault Pass-Through (LFP)
Diagram
Conditions
Dongle LED Presentation
Description
Color
Status
Normal Operations
PWR
Green
On
Link/ACT
Green
On
Fiber
Blue
On
Switch and Converter
disconnected
PWR
Green
On
Link/ACT
Green
Off
Fiber
Blue
Off
Converter TX Fiber
disconnected *
PWR
Green
On
Link/ACT
Green
Blinking every 5 seconds
Fiber
Blue
Off
Converter RX Fiber
disconnected *
PWR
Green
On
Link/ACT
Green
Off
Fiber
Blue
Off
*Note: The device at the remote side must support Link Fault Pass-Through (LFP).
QSRule
Installing the UTP-Fiber1G-USB
1. Plug the RJ45 connector of UTP-Fiber1G-USB into the RJ45 port of the target device.
2. Plug the USB type A connector of UTP-Fiber1G-USB into the USB port of the target device to serve as power source.

UTP-Fiber1G-USB QSG 3
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
3. Flip open the dust cover of the UTP-Fiber1G-USB to reveal the fiber port, then connect the fiber cable’s LC connector to the fiber port.
Warning: To prevent damage to the dust cover, do not bend it all the way back.
4. Connect the other end of the fiber cable to the fiber port of a target device to verify that the fiber connection is complete.
QSRule
Removing the UTP-Fiber1G-USB
1. Press the fiber cable’s connector and pull to remove it from UTP-Fiber1G-USB.
2. Remove the UTP-Fiber1G-USB's USB type A connector from its power source.
3. Press the latch down and pull to remove UTP-Fiber1G-USB from the target device's RJ45 port.
QSRule

UTP-Fiber1G-USB QSG 4
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
Product Specifications
General Specifications
Function
Fiber Converter dongle
RJ45 port
1000 Base-Tx Auto negotiation (IEEE 802.3u)
Fiber Port
1000 Base-X Full-duplex (IEEE 802.3u)
Properties of optic port
Total number of FO ports
1
Connector type
LC
Fiber Mode
Duplex Fiber
Link Distance (Max)
Up to 10Km for Single-mode fiber
Up to 800m for Multi-mode fiber
Data rate
1.25Gbps
Wavelength
1310nm
Optical Output Power Range
-1 ~ -5 dBm
Optical Receive Sensitivity
-21 ~ -3 dBm
Properties of RJ45 port
Total number of RJ45 Ethernet interfaces
1
Connection type
RJ45 male
Data rate
1000Mbps
MDI/MDIx switchover
Auto MDI/MDIX
Environmental Specifications
Operating temperature
0℃~55℃
Operating Humidity (Max)
5%~95%
Degree of protection
IP20
Power Requirements
Connector type
USB 3.0 / USB 2.0 Type A
Power Consumption
typical
2.1 W
maximum
2.5 W

UTP-Fiber1G-USB QSG 5
UTP_Fiber1G_USB-QSG-revA1 255-80-0069-00-RoHS
Physical Characteristics
Housing
Metal
Dimension
82.33(L)*20(W)*16.56(H) mm
Weight
50g
Standards and Certifications
EMC/EMI
Green product
RoHS and REACH
CE and FCC