Lehmannaudio Rhinelander User manual

Rhinelander
Headphone amplifier / Single Source Preamp
User manual

Lehmann audio Manual Rhinelander - page 2 -
_______________________________________________________________________________________________________________
Dear customer,
congratulations for uying the Lehmann audio Rhinelander. You will e rewarded with the est
possi le sound from your headphones. You can use practically all dynamic headphones on the market.
Carefully selected components and a highly sophisticated circuit design guarantee a very high level of
audio reproduction.
Please read this manual carefully and keep it near y the unit for future reference even if you
have experiences with other headphone amplifiers!
Precautions
Please read the following efore operating your Rhinelander.
While installing the Rhinelander
- Be careful to use an appropriate ca le for the connection etween your power outlet and the
Rhinelander. Make sure that you have the appropriate version for your mains voltage.
- Be careful to prevent Rhinelander from getting wet; do not allow water to enter the unit, especially
when raining or snowing, or near a ody of water. Otherwise fire or electrical shock may result.
- Do not place heavy o jects on the power cord. If the cord is damaged, fire or electrical shock may
result. In particular, it is possi le that one might accidentally place a heavy o ject on a carpet that
covers the cord; definitely avoid these situations!
- Do not install the Rhinelander in a place where it might e exposed to oil, smoke or steam (for
example, near a cooking ta le or humidifier). Otherwise, fire or electrical shock may result.
- Do not place the Rhinelander on an unsta le surface, such as an unsta le ench or slanted surface.
Otherwise, the device may fall or drop, resulting in an injury.
- Do not place the power cord near a heating device. Otherwise, the cord sheath may melt, resulting in
fire or electrical shock.
- Do not locate the Rhinelander in a place su ject to excessive heat, such as inside a car with all the
windows closed, or in direct sunlight. Otherwise, fire may result.
- Do not handle the power plug with wet hands. Otherwise you may receive an electrical shock.
- When you remove the power plug, e sure to hold the plug. Never pull on the cord. Otherwise, the
power cord may ecome damaged, resulting in fire or electrical shock.
- The Rhinelander offers super sonic quality. To ensure est possi le results, you should use the
est quality connecting ca les that you can afford. Regular maintenance involves keeping all
connections clean using a quality contact cleaner.

Lehmann audio Manual Rhinelander - page 3 -
_______________________________________________________________________________________________________________
Using the Rhinelander
Do not touch the Rhinelander under the following circumstances:
- If you hear thunder, remove the power plug from the AC outlet as soon as possi le. If you fear a
lightning hit and the Rhinelander has een connected to an AC outlet, do not touch the power plug.
Otherwise you may receive an electrical shock.
- Do not attempt to modify this equipment. Otherwise, fire or electrical shock may result. Warranty is void
on modified devices.
- If you think the Rhinelander needs to e checked for maintenance or repair, consult your dealer.
- Do not place a container of water or any small metal o ject on top of the Rhinelander. If water is spilled
or if the metal o ject gets inside, fire or electrical shock may result. This applies to vases, pottet plants,
glasses, cosmetic ottles, medicine, etc.
- Do not damage, process, end, twist, stretch or heat the power cord. If the cord is damaged, fire or
electrical shock may result.
- When you are connecting other audio devices to the Rhinelander make sure that you first turn off the
power to all devices to e connected. Refer to the user´s guide for each device and use the specific ca le
for connection.
- Set the volume levels of all devices (including that of the Rhinelander) to minimum efore connecting the
Rhinelander to your actual setup and to the AC outlet. Otherwise, an extremely loud noise could damage
your loudspeakers or even your hearing.
- If you plan not to use the Rhinelander for a long period of time (such as when you are on vacation),
remove the power plug from the AC outlet. Otherwise, a fire could possi ly result.
If any a normality occurs while using the Rhinelander, remove the plug from the AC outlet. In this
case first shut off the power amplifiers or turn down the volume controls and so on to avoid
possi ly damaging transients
- If you notice any a normality - such as smoke, smell, noise, etc. - remove the plug from the AC outlet.
Confirm that the a normality is no longer present, then consult your dealer for repair. If you continue
using the Rhinelander under a normal conditions, fire or electrical shock may result.
- If a foreign o ject or water enters inside the equipment, remove the Plug from the AC outlet and consult
your dealer for repair. If you continue using the Rhinelander under this condition, fire or electrical shock
may result.
- If the power cord is damaged (for example if it is cut or if the core wire is exposed), ask your dealer for a
replacement. If you continue using the Rhinelander under this conditions, fire or electrical shock may
result.
- If the Rhinelander is dropped, or if the case is damaged, remove the plug from the AC outlet and consult
your dealer. If you continue using the Black Cu e under a normal conditions, fire or electrical shock may
result.
Maintenance
- Before cleaning the Rhinelander remove the power plug from the AC outlet for safety. Otherwise, an
electrical shock may result.
- Do not open the Rhinelander. There are hazardous voltages inside that might result in an injury or an
electrical shock.

Lehmann audio Manual Rhinelander - page 4 -
_______________________________________________________________________________________________________________
Why headphones?
When you use headphones you can reach a very high level of sound reproduction at a fraction of the
price you would have to spend for a regular hfi setup with high quality loudspeakers. Detail resolution
and dynamics of even the est loudspeakers can easily e reached with the est headphones. In most
cases headphones will e used to enjoy music either to acoustically disclose a noisy environment to
just to e a le to listen to louder levels without distur ing other people.
What makes headphones different?
There is a num er of parallels etween (dynamic) headphones and loudspeakers. Technically they are
complex loads for the amplifiers driving them and should therefore e used with sta le outputs.
There are headphones with higher impedance that need a higher signal voltage and low impedance
types which need more current for optimal sonic results. Just connecting a headphone to any given
headphone output without considering the headphone’s electrical characteristics will most likely yield
dissatisfactory results.
Impedances of dynamic headphones can vary from 30 Ohms to 600 Ohms. Transferred to
loudspeakers this would result in impedances from 4 Ohms to 80 Ohms. The same signal amplitude
results in a power consumption difference of factor 20!
Loudspeakers and headphones are manufactured in a dazzling variety. Irrespective of their impedance
headphones and loudspeakers can have very different efficiencies which means that the electrical
signal is converted more or less efficient to acoustic energy. When comparing loudspeakers the
dimension used is the sound pressure level (SPL) reached at a given power of 1W (at 1m distance).
There is a similar parameter for the efficiency of headphones except for the fact that the standard
power is 1mw (=1/1000W) The figure is given as dB/mW which means the resulting sound pressure
level at 1mW (not per 1mW).

Lehmann audio Manual Rhinelander - page 5 -
_______________________________________________________________________________________________________________
If the power is dou led then the resulting sound pressure level is 3dB higher. If this is calculated the
other way round it means that only half of the power is needed when using a headphone with 3dB
more efficiency to reach the same sound pressure level. The 3dB formula is valid for headphones and
for loudspeakers.
From the given efficiency the power needed for a certain sound pressure level can e derived. The
power for the same sound pressure level can differ up to a factor of 500 for the different headphones
on the market. In the end what counts when selecting a headphone or a headphone amplifier is if the
desired volume can e reached without distortion. At least equally important is to avoid damage for
the headphone and – most important – to avoid damage for your hearing. The maximum power rating
is a figure that can e found in the data sheet of the headphone. From this power rating the
maximum voltage can e derived. If the voltage will e higher then the voice coils of the headphones
will e destroyed. Today most headphones allow hearing levels well a ove a secure level for the
listener. This means that a standard pair of cans might survive extremely high levels without any
degradation of long term performance ut the hearing of the listener might e seriously damaged.
Especially interesting are the standards of different regions. Taking a look at laws in the US and in
Europe reveals tremendous differences in what is thought to e suita le for the listener:
Permissi le noise exposures in Germany (dBA)1
SPL /dBA
Duration
85 88 91 94 97 100 103 106 109 112 115 118 121
hours per day 8 4 2 1
minutes per day 30 15 7,5
seconds per day 225 112 56 28 14 7
Permissi le noise exposures in the USA (dBA)2
SPL /dBA
Duration
90 92 95 97 100 102 105 110 115
hours per day 8 6 4 3 2 1,5 1
minutes per day 30 15
1 Roughly harmonized throughout Europe
2 Figures taken from US department of labour noise regulations

Lehmann audio Manual Rhinelander - page 6 -
_______________________________________________________________________________________________________________
Overview of power consumption of different headphones at different signal levels:
level
(veff)
Headphone impedances
32 Ohms 60 Ohms 120 Ohms 300 Ohms 600 Ohms
0,1V 0,31mW 0,16mW 0,08mW 0,033mW 0,016mV
0,5V 7,8mW 4,2mW 2,1mW 0,83mW 0,42mW
1V 31,3mW 16,7mW 8,3mW 3,3mW 1,7mW
2V 125mW 66,7mW 33,3mW 13,3mW 6,7mW
3V 281mW 150mW 75mW 30mW 15mW
4V 500mW 267mW 133mW 53mW 27mW
5V 781mW 420mW 210mW 83mW 42mW
6V 1,13W 600mW 300mW 120mW 60mW
7V 1,53W 817mW 408mW 163mW 82mW
8V 2W 1,06W 533mW 213mW 107mW
9V 2,53W 1,35W 680mW 270mW 135mW
Voltage needed for 1mW power
units Headphone impedances
32 Ohms 60 Ohms 120 Ohms 300 Ohms 600 Ohms
Volts 179mV 245mV 347mV 550mV 775mV
dBu
(0dB = 775mV)
-12,7 -10 -7 -3 0
dBV
(0dB = 1V)
-14,9 -12,2 -9,2 -5,2 -2,2

Lehmann audio Manual Rhinelander - page 7 -
_______________________________________________________________________________________________________________
Ta le of efficiency of common headphones3
Type Impedance
/Ohms
Efficiency
dB/1mW
Voltage for
100dB SPL
Power for 100dB
SPL
AKG
K141Studio 55 101 209mV 0,8mW
K240DF 600 88 3,1V 16mW
K501 120 94 694mV 4mW
K1000 120 74 6,93V 400mW
Beyerdynamic
DT660 32 97 253mV 2mW
DT770, DT880,
DT990
250 96 800mV 2,6mW
Grado
All 32 98 225mV 1,6mW
Koss
Portapro 60 101 218mV 0,8mW
Sennheiser
HD500 32 97 253mV 2mW
HD555 120 94 694mV 4mW
HD650 300 97 775mV 2mW
Ultrasone
HFI-15G 32 94 716mV 4mW
HFI-550 64 100 252mV 1mW
HFI-700 75 94 548mV 4mW
It can easily e seen that even among the products of one manufacturer there can e huge differences as far as
impedance and/or efficiency are concerned. This makes it very important that you either choose headphone and
headphone amplifier as a matching com ination or go for a headphone amplifier with switcha le gain that can
e used with a wide variety of headphones. Purchasing the Rhinelander was a perfect step in the right direction.
3 All figures were taken from freely available data sheets of different manufacturers and have been partly recalculated
from other dimensions. Voltage and power are referring to effective values and not to peak values. All figures are given
without any guarantee.

Lehmann audio Manual Rhinelander - page 8 -
_______________________________________________________________________________________________________________
Elements at the front section
| | | |
1 2 3 4
1. Power LED
When this LED is active the Rhinelander is connected to mains voltage switched on and ready for use.
2. Headphone output
6,3mm original Neutrik headphone jack for common headphones. When a headphone is connected to
this output the line output at the rear side of the unit will e muted in the single source preamp mode.
Warning: when you are also using the line output please make sure that the volume kno is turned to
minimum position (counter clockwise) to avoid sudden signal peaks. Please have in mind that the same
signal amplitudes can result in very different volume levels connected to power amps or to
headphones.
3. Mute switch / Source selector
With this toggle switch you either mute the input signal when the Rhinelander is in single source
preamp preamp mode or select the input source when the second pair of RCA connectors is used as
input.
4. Volume kno
Here you can adjust the desired output level. Turn clockwise to get a higher volume and counter
clockwise to lower the volume
W A R N I N G :
While using headphones you can easily reach volume levels that can seriously damage your hearing. Every time
efore you put on a pair of headphones you must make sure that the volume is set to an appropriate level!

Lehmann audio Manual Rhinelander - page 9 -
_______________________________________________________________________________________________________________
Elements at the rear side
| | |
1 2 3
1. Line input 1 (Stereo)
RCA connectors for the source you want to hear with the Rhinelander. The connector with the lack
colour ring is for the left channel, the one with the red colour ring is for the right channel.
2. Line output (Stereo)/Line input 2
RCA connectors for the connection of your power amplifier or active loudspeakers. The connector with
the lack colour ring is for the left channel, the one with the red colour ring is for the right channel.
Depending on which headphone output you are using on the front side of the unit the signal is either
fed through the Rhinelander to the line output or muted. This set of RCA jacks is connected in parallel
to the Rhinelander’s output stage and not just passively connected to the input connectors so that you
enefit greatly from the low output impedance when you use the unit as single source preamp.
These connectors can e reconfigured inside the unit to use them as second stereo input. To do so
please open the unit and place the jumpers to “input”. The jumpers shall e placed at the la el
“output” for the use as single source preamplifier. In this configuration the switch on the face plate
functions as mute switch for line input 1.
3. Power supply connector
Connector for the external power supply. Please use only the power supply included with your unit.
There is no mains switch.

Lehmann audio Manual Rhinelander - page 10 -
_______________________________________________________________________________________________________________
Adjustment of maximum gain
You can easily adjust the maximum gain of the Rhinelander to use most availa le headphones with est results
independent from their efficiency or impedance. The gain setting has direct effect on the active gain of the
input stage which is placed after the volume potentiometer. It is recommended that you choose a setting which,
at the maximum potentiometer position (turned clockwise), results in a volume level that is slightly higher than
your normal listening ha it so that you have a it of reserve with lower level signals. You also make sure that
extraordinary high levels can e avoided much easier. In case you want to use the Rhinelander as single source
preamp and for most dynamic headphones the default setting of 6dB gain should e a solutely sufficient. Only
for very inefficient headphones the 20dB setting is recommended. In case you need the 20dB gain setting you
have to open the unit and place the two Jumpers near the gain stage.
The gain setting is done for each channel separately. Please make sure that oth channels show the same
setting. Otherwise you will hear an a normally twisted stereo panorama.
2mm Hex Keys and two jumpers as well as two spare jumpers are included with the Rhinelander.
Warning: Do not change the gain setting while listening to avoid sudden peaks that might damage your
loudspeakers or even your hearing!

Lehmann audio Manual Rhinelander - page 11 -
_______________________________________________________________________________________________________________
Technical Data:
Input impedance : 47kOhm
Maximum gain : 6dB, 20dB (jumper configura le inside the unit)
Frequency response : 10Hz - 35kHz
Signal to noise ratio : >90dB @ Gain 6dB
Output impedance : Line Out 5 Ohms
Phones Out 5 Ohms
Connectors audio : Neutrik headphone jack (6,35mm) with gold plated contacts.
RCA connectors with gold plated contacts
Dimensions : 135 x 110 x 47mm³ (case only)
Weight : audio section 0,4kg
power supply 0,2kg
Manufacturer’s address:
Lehmann audio Vertrie s Gm H
Richard-Zanders-Str. 54
51469 Bergisch Glad ach
Tel.: +49 2202 – 280 62 40
Fax: +49 2202 – 280 62 39
email: [email protected]
We :
www.lehmannaudio.de
www.headphone-amplifier.com