Leica iCON excavate iCP41 User manual

Leica iCON excavate iCP41
Quick Guide
Version 1.0

en
de
fr
it
es
nl
da
no
sv
fi
pl
cs
hu
ro
el
br
ru
ja

Leica iCON excavate iCP41
Quick Guide
Version 1.0
English

iCON excavate iCP41, Important Information about your Instrument 2
en
Important Information about your Instrument
Read and follow the User Manual on the accompanying USB documentation card before
using the product or the accessories delivered with the product.
To ensure safety when using the system on a machine, please also observe the directions
and instructions contained in the User Manual and Safety Handbook issued by the machine
manufacturer.
Keep for future reference!
Intended use • Determining the position of a drill bit, a piling rig, an excavator bucket, a dozer or grader
blade, a snow groomer blade or a roller wheel.
• Calculating the distance between the blade, bucket or tower and a reference model
(surface, line or point).
• Logging a surface or points to create an as-built report.
• Acoustic and visible indication of the bucket position.

iCON excavate iCP41, Important Information about your Instrument 3
en
Labelling iCP41
The product must not be disposed with household waste.
Conformity to national
regulations
This device complies to part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any
interference received, including interference that
may cause undesired operation.
Contains:
FCC-ID: xxxxxxx IC: yyyyy-yyyy
iCP41, 3D Panel Excavator w. C. Case
P/N: 797048
797050
S/N: xxxxx
xxxxx
Leica Geosystems AG
CH — 9435 Heerbrugg
Made in Sweden 2016
Power
12 — 24 V DC, 6A max.
012506_001
• FCC Part 15, 22 and 24 (applicable in US)
• Hereby, Leica Geosystems AG, declares that the product Leica iCP41 is in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC. The
declaration of conformity can be consulted at http://www.leica-geosystems.com/ce.
Class 1 equipment according European Directive 1999/5/EC (R&TTE) can be
placed on the market and be put into service without restrictions in any EEA
member state.
• The conformity for countries with other national regulations not covered by the FCC part
15, 22 and 24 or European directive 1999/5/EC has to be approved prior to use and oper-
ation.

iCON excavate iCP41, Instrument Components 4
en
1 Instrument Components
iCP41
Do not cover the IR-Port this will interrupt the data transfer.
HSPA and WLAN antenna are not attached to the iCP41 when delivered.
a) Keypad
b) 7" LCD wide screen display
c) MENU button
d) Wifi antenna
e) IR-Port for data transfer
f) HSPA antenna
g) SMA Connectors
h) Ventilation cap
i) SIM card slot
j) USB 2.0 connector
k) Cover for communication ports
012509_001
aabf
de
hi j k
cg g

iCON excavate iCP41, Instrument Components 5
en
Description of buttons,
2D mode Button Description
Increases/decreases slope in Y-direction.
Increases/decreases slope in X-direction.
Increases/decreases offset.
Read and save setup height.

iCON excavate iCP41, Instrument Components 6
en
Reset button. Used for setting the reference level and resetting earlier
values in the menu.
Selecting a bucket.
Quick settings. Up to 10 user settings can be stored.
X-direction Used for setting the X-direction.
Return to the 3D main menu.
Button Description

iCON excavate iCP41, Instrument Components 7
en
Description of buttons,
3D mode
Navigation button. Allows you to navigate through the menus.
Press left/right arrows to move between bucket items.
Naming convention within this manual:
Enter button
Left / Right arrow buttons
Up / Down arrow buttons
Escape button
Button Description
Esc
Esc
Button Description
These buttons offset the reference model vertically up or down.
One push of the button equals 1 cm.
Opens the excavator’s internal system with the "select bucket" menu
open.

iCON excavate iCP41, Instrument Components 8
en
Opens a display window for the excavator’s internal system. It is not
possible to adjust the excavator’s system settings in this mode. Press the
button again to close the window.
Opens the excavator’s internal system. The system is still in 3D mode
(GPS). The excavator’s system settings can be changed.
Navigation button. Allows you to navigate through the menus.
Press left/right arrows to change the bucket’s reference point.
Naming convention within this manual:
Enter button
Left / Right arrow buttons
Up / Down arrow buttons
Escape button
Button Description
Esc
Esc

iCON excavate iCP41, Technical Data 9
en
2TechnicalData
Environmental specifi-
cations
Temperature
Ingress protection against water, dust and sand
Humidity
3 Care and Transport
Care and transport • Protect the product against shock and vibration.
• Periodically carry out functional tests particularly after the product has been dropped,
stored for long periods or transported.
Type Operating temperature [°C] Storage temperature [°C]
Instrument -25 to +55 -40 to +85
Type Protection
Instrument IP56 (IEC 60529)
Type Protection
Instrument Max 95 % non condensing
The effects of condensation are to be effectively counteracted by peri-
odically drying out the instrument.

iCON excavate iCP41, Operation 10
en
4Operation
Mount and Power-On
the iCP41
To power-on the iCP41 it must be mounted in the cradle. Perform the following steps to
install and start the iCP41.
Step Description
Snapping the iCP41 onto the cradle:
1. Put the iCP41 on the holding hooks in the bottom of the cradle.
2. Insert the iCP41 into the cradle. Make sure it snaps in place!
11
2
012513_001

iCON excavate iCP41, Operation 11
en
Turning the iCP41 On and Off:
3. Turn it ON/OFF via the power switch. This switch is located at the right side of the
cradle.
Releasing the iCP41 will also turn off the power!
Off
On
Step Description
004423_001

iCON excavate iCP41, Operation 12
en
To detach iCP41 from the cradle:
4. To release the iCP41 simply press the release button at the bottom of the cradle.
Then pull the iCP41 towards you and lift it up.
Step Description
1
2
012516_001

iCON excavate iCP41, EC Declaration of Conformity 13
en
5 EC Declaration of Conformity
EC Declaration of
Conformity This corresponds to EN ISO/IEC 17050-1.
We, Leica Geosystems AG, CH-9435 Heerbrugg (Switzerland), declare under our sole
responsibility that the product(s) iCON iCP40, iCP41, iCP42 (with FCC-ID: M4Y-AN622V01
and N7NMC7304), following the provision of Directive(s)
•2011/65/EU Restriction of hazardous substances (RoHS)
•2006/42/EC Machinery (MD)
•2014/30/EU Electromagnetic compatibility (EMC)
•1999/5/EC Radio and telecommunications terminal equipment (RTTE) (in accord-
ance with annex II)
to which this declaration relates, is in compliance with the following standards:
•EN 13309:2010
•ETSI EN 301489-1:V1.9.2
•ETSI EN 301489-3 V1.6.1
•ETSI EN 301489-17:V2.2.1
•ETSI EN 301489-7:V1.3.1
•ETSI EN 301489-24:V1.5.1
•EN 300440-2 V1.4.1
•EN 301511 V 9.0.2
•EN 301908-1 V6.2.1
•EN 301908-13 V6.2.1
•EN 300440-1 V1.6.1
•EN 300328:V1.8.1
•EN 301908-2 V6.2.1
• EN 60950-
1:2006+A11:2009+A1:2010+A12:2011
•EN 62311:2008
•EN ISO 12100:2010
•EN 474-1:2006+A4:2013
•EN 474-5:2006+A3:2013
•EN 474-2:2006+A1:2008
•EN 474-8:2006+A1:2009
Leica Geosystems AG

iCON excavate iCP41, EC Declaration of Conformity 14
en
For a signed version and translations into the official EU languages please refer to:
http://www.leica-geosystems.com/ce

iCON excavate iCP41, EC Declaration of Conformity 15
en

Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Phone [phone]
www.leica-geosystems.com
847210-1.0.0en
Original text
Printed in Switzerland
© 2016 Leica Geosystems AG, Heerbrugg, Switzerland