LEMKEN Gemini 5 User manual

Operating Instructions
Front tank
Gemini 5
- en -
Item no. 17512852
BA_00/04.15
LEMKEN GmbH & Co. KG
Weseler Straße 5, 46519 Alpen / Germany
Telephone [phone], Fax [phone]
[email protected], www.LEMKEN.com

1
Dear customer,
Thank you for the trust you have placed in us by purchasing this device. The de-
vice can only be used to its full advantage when operated and used properly.
When the device was delivered, you will already have been instructed in opera-
tion, adjustment and maintenance by your dealer. However, this brief instruction is
not a substitute for thorough study of the operating instructions.
These operating instructions will help to familiarise you with the LEMKEN GmbH &
Co. KG device and the options available for using it.
The operating instructions contain important information about how to operate the
device safely, properly and efficiently. Following the instructions will help to pre-
vent hazards, faults and down times and will increase reliability and service life.
Read the operating instructions carefully and attentively before commissioning.
Make sure that the operating instructions are always available at the location
where the device is used.
The operating instructions must be read and followed by anyone who is involved
in carrying out the following work:
Coupling and uncoupling
Adjustments
Operation
Maintenance and repairs
Troubleshooting, and
Final shutdown and disposal.

2
Spare parts ordering
This device is supplied with a specification listing all assemblies that are relevant
for the product. The spare parts list valid for your device includes both those as-
semblies relevant to you and those that are not intended for your device. Make
sure that you only order spare parts that belong to the assemblies that can be
found on your specification or the enclosed print out. When ordering spare parts,
state the type designation and serial number of the device. This information can
be found on the type plate. Enter this data in the fields below so that it is always to
hand.
Type designation:
Serial number:
Remember that you should only use genuine LEMKEN spare parts. Reproduction
parts have a negative influence on the function of the device, have a shorter ser-
vice life and present risks and hazards that cannot be estimated by LEMKEN
GmbH & Co. KG. They also increase the maintenance costs.
Service and spare parts
Information on service and spare parts is available from your local dealer or our
website at www.lemken.com.

3
CONTENTS
1General information..................................................................................................8
1.1 Liability...........................................................................................................................8
1.2 Guarantee ......................................................................................................................8
1.3 Copyright .......................................................................................................................9
1.4 Optional accessories ....................................................................................................9
1.5 Type plate ....................................................................................................................10
2Symbols used in the Operating Instructions........................................................12
2.1 Hazard classes ............................................................................................................12
2.2 Information...................................................................................................................12
2.3 Environmental protection...........................................................................................12
2.4 Indication of passages................................................................................................13
3Safety measures and precautions.........................................................................14
3.1 Target group................................................................................................................14
3.2 Intended use................................................................................................................14
3.3 Safety features of the device......................................................................................15
3.4 Safety and warning signs...........................................................................................15
3.4.1 General information...................................................................................................15
3.4.2 Overview of symbols..................................................................................................15
3.4.3 Meaning of warning signs..........................................................................................16
3.4.4 Meaning of other symbols..........................................................................................17
3.5 Special safety instructions.........................................................................................18
3.6 Danger areas................................................................................................................20
3.6.1 Danger areas during implement operation.................................................................21
3.7 Residual risks..............................................................................................................21
3.7.1 Hazard caused by mechanical systems.....................................................................22
3.7.2 Dangers from the oil hydraulic system.......................................................................22
3.8 Applicable Rules and Regulations.............................................................................22

4
3.9 Operation on public highways...................................................................................23
3.9.1 Lighting system and identification..............................................................................23
3.9.2 Front-mounted implements on public roads...............................................................23
3.10 Checking the field of view ..........................................................................................26
3.10.1 Identify a reference point........................................................................................26
3.10.2 Mark the starting point............................................................................................26
3.10.3 Measure the target point ........................................................................................26
3.10.4 Test the field of view...............................................................................................26
3.11 Measures to compensate for restriction of the field of view...................................27
3.11.1 Requirements of the tractor....................................................................................27
3.11.2 Axle loads...............................................................................................................28
4Delivery of the implement ......................................................................................33
5Layout and description...........................................................................................34
5.1 Overview ......................................................................................................................34
5.2 Three-point connection ..............................................................................................35
5.3 Step ..............................................................................................................................35
5.4 Deflector.......................................................................................................................36
5.5 Mounting and transport carriage...............................................................................36
5.6 Liquid flow ...................................................................................................................36
5.7 Tanks............................................................................................................................37
5.8 Combined filling and suction hose............................................................................39
5.9 Lighting and signs ......................................................................................................39
6Preparations on the tractor....................................................................................41
6.1 Overview ......................................................................................................................41
6.1.1 Check tractor tire pressure ........................................................................................41
6.1.2 Provide and check the necessary electronic connections..........................................42
6.1.3 Setting the three-point linkage...................................................................................42
6.1.4 Checking the three-point connection .........................................................................42
6.1.5 Install connection hose holders .................................................................................43

5
7Attaching the implement ........................................................................................44
7.1 Preparation and making ready...................................................................................45
7.1.1 Existing platform........................................................................................................45
7.1.2 LEMKEN mounting and transport carriage................................................................46
7.2 Adjusting the coupling points for the lower links ....................................................46
7.3 Adjusting the coupling point for the top link............................................................48
7.4 Existing platform.........................................................................................................49
7.5 Removing the LEMKEN mounting and transport carriage ......................................49
8Operation .................................................................................................................51
8.1 Operation below zero..................................................................................................51
8.2 Deflector.......................................................................................................................51
8.2.1 Detaching ..................................................................................................................51
8.2.2 Attaching....................................................................................................................52
8.3 Step ..............................................................................................................................53
8.3.1 Pulling the step out....................................................................................................53
8.3.2 Pushing the step in....................................................................................................54
8.4 Filling and emptying tanks.........................................................................................54
8.4.1 Filling.........................................................................................................................55
8.4.2 Emptying....................................................................................................................59
8.5 Test run with the implement.......................................................................................64
9Cleaning...................................................................................................................66
9.1 General information ....................................................................................................66
9.2 Internal cleaning..........................................................................................................67
9.2.1 General information...................................................................................................67
9.2.2 Cleaning ....................................................................................................................67
9.3 External cleaning.........................................................................................................71
9.3.1 Clear water in the front tank.......................................................................................72
9.3.2 Liquid fertiliser in the front tank..................................................................................73

6
10 Detaching the implement .......................................................................................74
10.1 General advice.............................................................................................................74
10.1.1 With a non-transportable existing platform.............................................................75
10.1.2 With a transportable existing platform....................................................................76
10.1.3 With the LEMKEN mounting and transport carriage...............................................77
11 Wintering..................................................................................................................81
12 Maintenance and repairs........................................................................................82
12.1 Special safety instructions.........................................................................................82
12.1.1 General ..................................................................................................................82
12.1.2 Personnel qualifications .........................................................................................82
12.1.3 Protective equipment..............................................................................................82
12.1.4 Immobilise the implement for maintenance and repairs.........................................83
12.1.5 Working on the electrics.........................................................................................83
12.1.6 Working under the raised device............................................................................84
12.1.7 Utilised tool.............................................................................................................84
12.2 Environmental protection...........................................................................................85
12.3 Lubricating...................................................................................................................85
12.4 Maintenance intervals.................................................................................................86
12.5 Lashing straps.............................................................................................................87
12.5.1 Check.....................................................................................................................87
12.5.2 Tightening...............................................................................................................87
12.6 Tightening torques......................................................................................................88
12.6.1 General ..................................................................................................................88
12.6.2 Bolts and nuts made of steel..................................................................................88
12.6.3 Bolts and nuts made of V2A...................................................................................89
13 Technical data .........................................................................................................90
13.1 Dimensions..................................................................................................................90
13.2 Weights ........................................................................................................................91
13.3 Permissible masses....................................................................................................91

7
13.4 Mounting and transport carriage...............................................................................91
13.4.1 Transport rollers.....................................................................................................91
13.4.2 Locating point for fork-lift forks ...............................................................................92
13.5 Three-point connection ..............................................................................................92
13.6 Tank volume ................................................................................................................92
13.7 Spray fluid system ......................................................................................................93
13.7.1 Filling connection....................................................................................................93
13.7.2 Combined filling and intake connection..................................................................93
13.7.3 Combined filling and suction hose for field sprayer with corresponding connections93
14 Noise, Airborne Sound ...........................................................................................94
15 Notes ........................................................................................................................94
Index ...............................................................................................................................95

General information
8
1 GENERAL INFORMATION
1.1 Liability
The "Standard Terms and Conditions of Sales and Delivery" of LEMKEN GmbH &
Co. KG, in particular Section IX, shall apply. Liability. In line with the dimensions
cited in these conditions the LEMKEN GmbH & Co. KG shall not be held liable for
any personal or material damage, when such damage is caused by one or more
of the following reasons:
improper use of the device, see also section entitled "Intended use",
non-compliance with the operating instructions and the enclosed safety instruc-
tions,
unauthorised changes to the device,
inadequate monitoring of parts which are subject to wear,
maintenance work that has not been conducted properly or in good time,
the use of spare parts that are not original LEMKEN GmbH & Co. KG spare
parts,
accidents or damage through outside influences or force majeure
1.2 Guarantee
The "Standard Terms and Conditions of Sales and Delivery" of LEMKEN GmbH &
Co. KG shall apply at all times.
The guarantee period shall be one year from the date of receipt of the implement.
We shall rectify any implement faults in accordance with the LEMKEN guarantee
guidelines.

General information
9
1.3 Copyright
These operating instructions represent a document in terms of the law on unfair
competition.
Copyright is retained by
LEMKEN GmbH & Co. KG
Weseler Strasse 5
D-46519 Alpen, Germany
These operating instructions are intended to be used by the user of the imple-
ment. They contain texts and drawings which must not be
reproduced,
divulged or
communicated in any other way in whole or in part without the express permis-
sion of the manufacturer.
Infringements will result in a claim for damages.
1.4 Optional accessories
LEMKEN implements may be equipped with various accessories. The operating
instructions below describe both series components and optional accessories.
Please note: These accessories will vary depending on the type of equipment.

General information
10
1.5 Type plate
The implement carries a type plate.
The type plate can be found at front right
on the implement.
The operating instructions may apply to
different implement types or variants of the
implement.
The operating instructions indicate infor-
mation which only applies to a specific im-
plement type or a specific variant of the
implement.
The type plate will help you to identify the
implement type and variant.
Layout of the type plate
Illustration: Example of a type plate
Illustration: Example of a type plate, France only

General information
11
1
Series
2
Type designation
3
Serial number
4
Year of manufacture
5
Permissible drawbar load [kg]
6
Permissible axle load [kg]
7
Permissible gross weight [kg]
8
Company logo and address
9
CE marking
(only within the European Union)
10
Name of manufacturer
11
Type, variant, version
12
Type approval date

Symbols used in the Operating Instructions
12
2 SYMBOLS USED IN THE OPERATING INSTRUCTIONS
2.1 Hazard classes
The following symbols are used in the Operating Instructions for particularly im-
portant information:
DANGER
Denotes an imminent hazard with high risk, which will result in
death or severe physical injury, if not avoided.
WARNING
Denotes a possible hazard with medium risk, which could result in
death or severe physical injury, if not avoided.
CAUTION
Denotes a low-risk hazard, which could cause light or medium
physical injury or property damage, if not avoided.
2.2 Information
Denotes special user tips and other particularly useful or important
information for operation and efficient utilisation.
2.3 Environmental protection
Indication of special recycling and environmental protection
measures.

Symbols used in the Operating Instructions
13
2.4 Indication of passages
The following symbols are used for particular passages in the operating instruc-
tions:
Indicates work steps
Indicates enumerations

Safety measures and precautions
14
3 SAFETY MEASURES AND PRECAUTIONS
General safety instructions for the operator are specified in the chapter entitled
«Safety measures and precautions». At the start of some main chapters the safety
instructions, which refer to all work to be carried out in this chapter, are listed to-
gether. Each safety-relevant work step includes other safety instructions specific
to the work step.
3.1 Target group
These operating instructions are restricted exclusively to the use of the device by
trained technicians and instructed persons.
3.2 Intended use
The device is manufactured in accordance with state-of-the-art standards and the
recognised safety rules. However, the use of the device may result in a risk to life
and limb of the user or third parties, or cause damage to the device and other ma-
terial property. The device may be operated in a technically perfect condition only,
in accordance with its designated use and by safety-conscious persons in compli-
ance with the operating instructions.
Intended use also includes:
compliance with the operating instructions and implementation of the work
steps indicated in the operating instructions,
compliance with the safety and warning signs on the device,
observance of the power limits of the tractor and device,
observance of all maintenance specifications and additional checks,
the use of original spare parts,
the use of the listed auxiliary and operating materials as well as their environ-
mentally friendly disposal.
Safe operation is not guaranteed unless all instructions, settings and power limits
applicable to the device are observed.
The machine is only suitable for the usual agricultural use.

Safety measures and precautions
15
3.3 Safety features of the device
To protect the operator and the device, the device is equipped with special safety
features in accordance with country specific requirements.
Always keep all safety devices in working order.
3.4 Safety and warning signs
3.4.1 General information
The implement features all equipment
which ensures safe operation. If hazardous
areas could not be completely secured
with respect to operational safety, warning
signs are affixed which indicate these resi-
dual risks. Damaged, lost or illegible warn-
ing signs must be replaced immediately.
3.4.2 Overview of symbols

Safety measures and precautions
16
3.4.3 Meaning of warning signs
Please familiarise yourself with the
meaning of the warning signs.
The following explanations provide detailed
information.
Please read and observe the operating in-
structions and safety instructions before
starting up the implement for the first time.
Before carrying out maintenance or repair
work, switch off the engine and remove
key.
When the three-point power lift is activated,
stay outside of the lifting range of the three-
point suspension.

Safety measures and precautions
17
Do not ride on the platform of the imple-
ment.
Risk of poisoning –Never get into the con-
tainer.
3.4.4 Meaning of other symbols.
The label shows the
Implement inspection data
Maximum implement weights, empty
and full
Locating points for fork-lift

Safety measures and precautions
18
3.5 Special safety instructions
WARNING
Risk of injury due to non-observance of the currently valid
occupational safety guidelines
If the currently valid occupational safety guidelines are bypassed
or safety equipment is rendered unusable when handling the de-
vice, there is a risk of injury.
The operator must personally monitor all work on and with the
device.
The operator instructs his personnel in occupational safety ac-
cording to the currently valid occupational safety guidelines.
WARNING
Risk of injury in hazard zone
While working with the machine, there is a risk of injury to the face
and body through moving implement parts.
During work there must be nobody directly in front of, behind or
next to the implement.
During work nobody must accompany the implement.