Lenovo ThinkSystem SR250 V3 Service manual

ThinkSystem SR250 V3
Messages and Codes Reference
Machine Types: 7DCL and 7DCM

Note
Before sing this information and the prod ct it s pports, be s re to read and nderstand the safety
information and the safety instr ctions, which are available at:
https://p bs.lenovo.com/safety_doc mentation/
In addition, be s re that yo are familiar with the terms and conditions of the Lenovo warranty for yo r server,
which can be fo nd at:
http://datacenters pport.lenovo.com/warrantylook p
First Edition (February 2024)
© Copyright Leno o 2024.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is deli ered pursuant to a General Ser ices
Administration (GSA) contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.
GS-35F-05925

Contents
Contents . . . . . . . . . . . . . . . . . i
Chapter 1. Messages . . . . . . . . . . 1
Event and alert message format . . . . . . . . . 1
Chapter 2. XClarity Controller
e ents . . . . . . . . . . . . . . . . . . 5
XCC events that a tomatically notify S pport . . . . 6
XCC events organized by severity. . . . . . . . . 7
List of XClarity Controller events . . . . . . . . 26
Chapter 3. UEFI e ents . . . . . . . . 145
UEFI events organized by severity . . . . . . . 145
List of UEFI events. . . . . . . . . . . . . . 148
Chapter 4. XClarity Pro isioning
Manager e ents . . . . . . . . . . . . 167
LXPM events organized by severity . . . . . . . 167
List of XClarity Provisioning Manager events . . . 170
Appendix A. Getting help and
technical assistance . . . . . . . . . . 191
Before yo call . . . . . . . . . . . . . . . 191
Collecting service data . . . . . . . . . . . . 192
Contacting S pport . . . . . . . . . . . . . 193
© Copyright Lenovo 2024 i

ii ThinkSystem SR250 V3 Messages and Codes Reference

Chapter 1. Messages
When attempting to resolve iss es with yo r server, the best practice is to begin with the event log of the
application that is managing the server.
• If yo are managing the server from the Lenovo XClarity Administrator, begin with the Lenovo XClarity
Administrator event log.
• If yo are sing some other management application, begin with the Lenovo XClarity Controller event log.
The event log contains server hardware events that are recorded by the Lenovo XClarity Controller or by
UEFI. In addition, events can be generated when yo perform diagnostic testing on hard drives or memory
thro gh the Lenovo XClarity Provisioning Manager (altho gh these events are not stored in the event log).
Use this section to view the events that can be generated by Lenovo XClarity Controller, UEFI, or the Lenovo
XClarity Provisioning Manager. For each event, a ser action is available to help yo nderstand what m st
be done to resolve the iss e.
Important:
• The server s pports Lenovo XClarity Controller 2 (XCC2). For additional information abo t Lenovo XClarity
Controller 2 (XCC2), refer to https://p bs.lenovo.com/lxcc-overview/.
• Lenovo XClarity Provisioning Manager (LXPM) s pported version varies by prod ct. All versions of Lenovo
XClarity Provisioning Manager are referred to as Lenovo XClarity Provisioning Manager and LXPM in this
doc ment, nless specified otherwise. To see the LXPM version s pported by yo r server, go to https://
p bs.lenovo.com/lxpm-overview/.
E ent and alert message format
Yo can se the following content to help yo nderstand the event and alert message format.
The following information is provided for each event message.
E ent identifier
A string that niq ely identifies the event or class of events. This is a 12 character string in the following
format:
FQXppnnxxxxc
where:
• pp indicates the prod ct where the event originate, as follows.
– CM. Chassis Management.
– HM. Hardware manager.
– PM. XClarity Provisioning manger - LXPM (LEPT).
– SF. System Firmware.
– SP. Service Processor.
• nn identifies the component or system management where the event originated, as follows:
Components
– AA. Canister/Appliance - Contains system components not expected to be serviced by a
c stomer.
– CA. Cooling - Fans, blowers, m x cards, policies, chillers/refrigeration, water management nits,
water p mps, water filtration, air flow sensors, thermal monitors.
© Copyright Lenovo 2024 1

– DA. Display - Graphics adapters, op panel, monitor/console (incl ding front/back panel, control
panel, LCD panel etc).
– IO. I/O connectivity - PCI/USB h b, bridge, b s, risers, config ration settings, interconnect,
keyboard, mo se, KVM.
– MA. Memory - Incl des DIMMs, memory card, config ration settings, memory controller,
red ndant modes (mirroring, spare, etc), RAID memory, NVRAM, EPROM.
– PU. Processing - Involves the processor, processor cards and system board (system board
assembly), config ration settings, and microcode, cache, Tr sted Comp ting Mod le, processor
interconnect (QPI cables).
– PW. Power - Can be power s pplies, VRMs, VRDs, voltage levels, system power state, policies,
batteries, AT power width, TPMD, power controllers, external power, Battery Back p Unit (UPS),
PDUs.
– SB. System Board - Main system board, associated risers, system planar, mid-planes,
backplanes, interconnects.
– SD. Client Data Storage Device - Flash storage adapters, drives, cd/dvd drives, SSD, SAS, DASD,
Flash storage, tape, vol mes, remoteCopy, flashCopy, managed Storage Systems.
– SR. Storage RAID - Adapters, config ration, settings, interconnect, arrays, drive enclos res.
– VD. VPD - Config ration settings, EPROMs, comm nication.
Systems Management - FSM, PSM, HMC, FDMC UEFI, CMM, IOMC, CCE, PMC, DPSM, SVC,
management of storage, services, IMM, FSP, systems management networking.
– BR. Systems Management - Back p/Restore & Failover (HA).
– BT. System management - Boot, reboot, hard/warm reset, sh tdown.
– CL. LEPT Clone.
– CN. Systems Management - Console.
– CP. Systems Management - Config Patterns.
– CR. Systems Management - Core / Virt al Appliance.
– DD. Device Driver - AIX, IBM I, S bsystem Device Driver (SDD), IPMI Service.
– DM. Systems Management - Data Management.
– EA. Vendor Events.
– EM. Events Monitoring - LEPT Dash Board.
– EM. Systems Management - Events / Monitoring.
– FC. Systems Management - FlexCat OS/Config deployment.
– FW. System management - Firmware.
– HA. Hypervisor - Virt al Components, Boots, Crashes, SRIOV, LPARs.
– IF. Interconnect (Fabric) - common, podm, icm, lrim (SWFW major, vario s minors & f nctions).
– II. Interconnect (Interfaces) - cimp, smis, cli, mapi (SCFG major).
– IM. Interconnect (PCI Manager) - pcim (SWFW major, vario s minors and f nctions).
– IN. Interconnect (Networking) - bos, ethm, fcf, npiv (FCF major pl s SWFW major, vario s minors &
f nctions) data network, network settings, ports, sec rity, adapters, switches, fiber channel,
optical ports, Ethernet.
– IP. Interconnect (PIE) - tbd.
– IU. Interconnect (Utilities / Infrastr ct re) - til, infr, serv, isds (IBIS major), remote copy (storage).
– NM. Network Management - LEPT Welcompage.
– NM. Systems Management - Network Management.
– OH. OS/Hypervisor Interface - Passing of error logs, partition management, services (time, etc).
– OS. LEPT OS Deploy.
– OS. OS - Power Lin x, AIX IPL, AIX, crash and d mp codes, IBM i kernal code, IBM i OS,
management of storage.
– PR. System management - Entity presence.
– RC. Systems Management - Remote Control.
– SD. LEPT Storage Test.
– SE. Systems Management - Sec rity.
– SR. LEPT Raid Set p.
– SS. Service & S pport - LEPT FFDC Collection.
2ThinkSystem SR250 V3 Messages and Codes Reference

– SS. Systems Management - Service & S pport.
– TR. Time Reference - RTC, Master clock, drawer clocks, NTP.
– UN. Unknown/any entity.
– UP. LEPT Firmware Update.
– UP. Systems Management - Updates.
– WD. System management - Watchdog.
• xxxx is an incrementing n mber of the S b-System events set.
• c identifies the severity, as follows.
– A. Reserved as Immediate Action.
– B. Unknown / No action.
– D. Reserved - Immediate Decision.
– E. Reserved - Event al Action.
– F. Warning / No Action.
– G. Warning / Deferred Action.
– H. Minor / Deferred Action.
– I. Information / No Action.
– J. Minor / Immediate Action.
– K. Major / Deferred Action.
– L. Major / Immediate Action.
– M. Critical / Immediate Action.
– N. Fatal / Immediate Action.
– W. Reserved - System Wait.
Chapter 1.Messages 3

4ThinkSystem SR250 V3 Messages and Codes Reference

Chapter 2. XClarity Controller e ents
When a hardware event is detected by the Lenovo XClarity Controller on the server, the Lenovo XClarity
Controller writes that event in the system-event log on the server.
Notes: Event identifier (ID) is a niq e identifier sed to search for XCC events. The event message may
have one or more arg ments, which co ld be replaceable text of FRU name or sensor name to identify the
failed component. So one XCC event ID co ld represent a generic event or similar fa lts that happened on
different hardware components. The general way of problem determination is to locate the event by ID,
identify the hardware component by message arg ment if it contains hardware component name, and then
perform actions defined in User Action.
Example:
FQXSPCA0017M: Sensor [SensorElementName] has transitioned to critical from a less severe state
where:
• FQXSPCA0017M is the event ID.
• [SensorElementName] is a sensor variable, indicating the name of hardware component. It can be CPU,
PCI adapter, OCP card or chipset. Yo can find the event by the event ID FQXSPCA0017M and perform
actions defined in User Action for the component.
For additional information abo t the Lenovo XClarity Controller event log, see “Viewing Event Logs” section
in the XCC doc mentation compatible with yo r server at https://p bs.lenovo.com/lxcc-overview/.
For each event code, the following fields are displayed:
E ent identifier
An identifier that niq ely identifies an event.
E ent description
The logged message string that appears for an event. When the event string is displayed in the event
log, information s ch as a specific component is displayed. In this doc mentation, that additional
information appears as variables, which incl de b t not limited to the following:
• [SensorElementName], [ManagedElementName] , [ProcessorElementName],
[ComputerSystemElementName], [PowerSupplyElementName], ...
• [arg1], [arg2], [arg3], [arg4], [arg5]...
Explanation
Provides additional information to explain why the event occ rred.
Se erity
An indication of the level of concern for the condition. The following severities can be displayed.
• Informational. The event was recorded for a dit p rposes, s ally a ser action or a change of states
that is normal behavior.
• Warning. The event is not as severe as an error, b t if possible, the condition sho ld be corrected
before it becomes an error. It might also be a condition that req ires additional monitoring or
maintenance.
• Error. The event is a fail re or critical condition that impairs service or an expected f nction.
Alert Category
Similar events are gro ped together in categories. The alert category is in the following format: se erity -
de ice, where:
© Copyright Lenovo 2024 5

• se erity is one of the following severity levels:
– Critical. A key component in the server is no longer f nctioning.
– Warning. The event might progress to a critical level.
– System. The event is the res lt of a system error or a config ration change.
• de ice is the specific device in the server that ca sed the event to be generated.
Ser iceable
Specifies whether ser action is req ired to correct the problem.
CIM Information
Provides the prefix of the message ID and the seq ence n mber that is sed by the CIM message
registry.
SNMP Trap ID
The SNMP trap ID that is fo nd in the SNMP alert management information base (MIB).
Automatically contact Ser ice
Yo can config re the Lenovo XClarity Administrator to a tomatically notify S pport (also known as call
home) if certain types of errors are enco ntered. If yo have config red this f nction and this field is set
to Yes, Lenovo S pport will be notified a tomatically if the event is generated. While yo wait for Lenovo
S pport to call, yo can perform the recommended actions for the event.
Note: This doc mentation incl des references to IBM web sites, prod cts, and information abo t
obtaining service. IBM is Lenovo's preferred service provider for the Lenovo server prod cts.
For more information abo t enabling Call Home from Lenovo XClarity Administrator, see http://
sysmgt.lenovofiles.com/help/topic/com.lenovo.lxca.doc/admin_set pcallhome.html. In addition, see “XCC
events that a tomatically notify S pport” on page 6 for a consolidated list of all Lenovo XClarity
Controller events that are called home to Lenovo S pport.
User Action
Indicates what actions yo sho ld perform to solve the event. Perform the steps listed in this section in
the order shown ntil the problem is solved. If yo cannot solve the problem after performing all steps,
contact Lenovo S pport.
XCC e ents that automatically notify Support
Yo can config re the XClarity Administrator to a tomatically notify S pport (also known as call home) if
certain types of errors are enco ntered. If yo have config red this f nction, see the table for a list of events
that a tomatically notify S pport.
Table 1. E ents that automatically notify Support
E ent ID Message String
FQXSPEM4014I The RAID controller has problem with the battery. Please contact technical
s pport to resolve this iss e.([arg1],[arg2],[arg3],[arg4],[arg5])
FQXSPEM4015I The RAID controller detected nrecoverable error. The controller needs
replacement.([arg1],[arg2],[arg3],[arg4],[arg5])
FQXSPEM4025I One or more virt al drive have problem. Please contact technical s pport to
resolve this iss e.([arg1],[arg2],[arg3],[arg4],[arg5])
FQXSPEM4026I Drive error was detected by RAID controller. Please contact technical s pport
to resolve this iss e.([arg1],[arg2],[arg3],[arg4],[arg5])
FQXSPIO0001L The connector [PhysicalConnectorElementName] has enco ntered a
config ration error.
6ThinkSystem SR250 V3 Messages and Codes Reference

Table 1. E ents that automatically notify Support (continued)
E ent ID Message String
FQXSPIO0011N An Uncorrectable Error has occ rred on [SensorElementName].
FQXSPIO0015M Fa lt in slot [PhysicalConnectorSystemElementName] on system
[Comp terSystemElementName].
FQXSPMA0007L Scr b Fail re for [PhysicalMemoryElementName] on S bsystem
[MemoryElementName].
FQXSPMA0008N Uncorrectable error detected for [PhysicalMemoryElementName] on
S bsystem [MemoryElementName].
FQXSPMA0011G Memory Logging Limit Reached for [PhysicalMemoryElementName] on
S bsystem [MemoryElementName].
FQXSPPU0004M [ProcessorElementName] has Failed with FRB1/BIST condition.
FQXSPPW0002L [PowerS pplyElementName] has Failed.
FQXSPPW0035M N meric sensor [N mericSensorElementName] going low (lower critical) has
asserted.
FQXSPPW0047M N meric sensor [N mericSensorElementName] going high ( pper critical) has
asserted.
FQXSPPW0063M Sensor [SensorElementName] has transitioned to critical from a less severe
state.
FQXSPSD0001L The [StorageVol meElementName] has a fa lt.
FQXSPSD0002G Fail re Predicted on [StorageVol meElementName] for array
[Comp terSystemElementName].
FQXSPSD0002L Drive [arg1] in the enclos re/chassis(MTM-SN: [arg2]) has a fa lt.
FQXSPSD0003G Fail re Predicted on drive [arg1] in the enclos re/chassis (MTM-SN: [arg2]).
FQXSPSD0006L Array [Comp terSystemElementName] has failed.
FQXSPSD0008L Array failed on drive [arg1] in the enclos re/chassis (MTM-S/N: [arg2]).
FQXSPSS4004I Test Call Home Generated by ser [arg1].
FQXSPSS4005I Man al Call Home by ser [arg1]: [arg2].
XCC e ents organized by se erity
The following table lists all XCC events, organized by severity (Information, Error, and Warning).
Table 2. E ents organized by se erity
E ent ID Message String Se erity
FQXSPBR4000I Management Controller [arg1]: Config ration restored from a file by
ser [arg2].
Informational
FQXSPBR4002I Management Controller [arg1] Reset was ca sed by restoring defa lt
val es.
Informational
FQXSPBR4004I Server timeo ts set by ser [arg1]: EnableOSWatchdog=[arg2],
OSWatchdogTimo t=[arg3], EnableLoaderWatchdog=[arg4],
LoaderTimeo t=[arg5].
Informational
Chapter 2.XClarity Controller events 7

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPBR4005I Management Controller [arg1]: Config ration saved to a file by ser
[arg2].
Informational
FQXSPBR4006I Management Controller [arg1]: Config ration restoration from a file by
ser [arg2] completed.
Informational
FQXSPBR4009I Management Controller [arg1]: cloning config ration from neighbor
server [arg2] by gro p name [arg3].
Informational
FQXSPBR400AI Management Controller [arg1]: cloning config ration from neighbor
server [arg2] by gro p name [arg3] completed.
Informational
FQXSPBR400BI Management Controller [arg1]: cloning config ration from neighbor
server [arg2] by gro p name [arg3] failed to complete.
Informational
FQXSPBR400CI Management Controller [arg1]: cloning config ration from neighbor
server [arg2] by gro p name [arg3] failed to start.
Informational
FQXSPBR400DI Neighbor gro p clone config ration was initiated by ser [arg1]. Informational
FQXSPBR400EI Neighbor gro p firmware pdate was initiated by ser [arg1]. Informational
FQXSPBR400FI The neighbor gro p management is [arg1] by ser [arg2] from [arg3] at
IP address [arg4].
Informational
FQXSPCA2002I N meric sensor [N mericSensorElementName] going low (lower
critical) has deasserted.
Informational
FQXSPCA2007I N meric sensor [N mericSensorElementName] going high ( pper
non-critical) has deasserted.
Informational
FQXSPCA2009I N meric sensor [N mericSensorElementName] going high ( pper
critical) has deasserted.
Informational
FQXSPCA2011I N meric sensor [N mericSensorElementName] going high ( pper
non-recoverable) has deasserted.
Informational
FQXSPCA2015I Sensor [SensorElementName] has deasserted the transition from
normal to non-critical state.
Informational
FQXSPCA2017I Sensor [SensorElementName] has transitioned to a less severe state
from critical.
Informational
FQXSPCA2019I Sensor [SensorElementName] has deasserted the transition to non-
recoverable from a less severe state.
Informational
FQXSPCN4000I Serial Redirection set by ser [arg1]: Mode=[arg2], Ba dRate=[arg3],
StopBits=[arg4], Parity=[arg5], SessionTerminateSeq ence=[arg6].
Informational
FQXSPCN4001I Remote Control session started by ser [arg1] in [arg2] mode. Informational
FQXSPCN4002I User [arg1] has terminated an active console session. Informational
FQXSPCN4003I Remote Control session started by ser [arg1] in [arg2] mode has
been closed.
Informational
FQXSPCR2001I Sensor [SensorElementName] has deasserted the transition to non-
recoverable from a less severe state.
Informational
FQXSPDM4000I Inventory data changed for device [arg1], new device data hash=
[arg2], new master data hash=[arg3] .
Informational
FQXSPDM4001I Storage [arg1] has changed. Informational
8ThinkSystem SR250 V3 Messages and Codes Reference

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPDM4003I TKLM servers set by ser [arg1]: TKLMServer1=[arg2] Port=[arg3],
TKLMServer2=[arg4] Port=[arg5], TKLMServer3=[arg6] Port=[arg7],
TKLMServer4=[arg8] Port=[arg9].
Informational
FQXSPDM4004I TKLM servers device gro p set by ser [arg1]:
TKLMServerDeviceGro p=[arg2] .
Informational
FQXSPDM4005I User [arg1] has generated a new encryption key pair and installed a
self-signed certificate for the TKLM client.
Informational
FQXSPDM4006I User [arg1] has generated a new encryption key and certificate
signing req est for the TKLM client.
Informational
FQXSPDM4007I User [arg1] has imported a signed certificate for the TKLM client from
[arg2].
Informational
FQXSPDM4008I User [arg1] has imported a server certificate for the TKLM server. Informational
FQXSPDM4009I User [arg1] has [arg2] file [arg3] from [arg4]. Informational
FQXSPDM4010I Inventory data collecting and processing complete for [arg1],
seq ence n mber is [arg2].
Informational
FQXSPEA2001I Sensor [SensorElementName] has deasserted the transition from
normal to non-critical state.
Informational
FQXSPEA2002I Sensor [SensorElementName] has transitioned to a less severe state
from critical.
Informational
FQXSPEA2003I Link p is detected on port [arg1] of the PCIe device [arg2]. Informational
FQXSPEM0003I The Log [RecordLogElementName] has been cleared. Informational
FQXSPEM0004I The Log [RecordLogElementName] is f ll. Informational
FQXSPEM0005I The Log [RecordLogElementName] is almost f ll. Informational
FQXSPEM0009I The System [Comp terSystemElementName] has generated an
a xiliary Log Entry in Log [RecordLogElement].
Informational
FQXSPEM4000I The [arg1] on system [arg2] cleared by ser [arg3]. Informational
FQXSPEM4001I The [arg1] on system [arg2] is 75% f ll. Informational
FQXSPEM4002I The [arg1] on system [arg2] is 100% f ll. Informational
FQXSPEM4003I LED [arg1] state changed to [arg2] by [arg3]. Informational
FQXSPEM4004I SNMP [arg1] enabled by ser [arg2] . Informational
FQXSPEM4005I SNMP [arg1] disabled by ser [arg2] . Informational
FQXSPEM4006I Alert Config ration Global Event Notification set by ser [arg1]:
RetryLimit=[arg2], RetryInterval=[arg3], EntryInterval=[arg4].
Informational
FQXSPEM4007I Alert Recipient N mber [arg1] pdated: Name=[arg2],
DeliveryMethod=[arg3], Address=[arg4], Incl deLog=[arg5], Enabled=
[arg6], EnabledAlerts=[arg7], AllowedFilters=[arg8] by ser [arg9] from
[arg10] at IP address [arg11].
Informational
FQXSPEM4008I SNMP Traps enabled by ser [arg1]: EnabledAlerts=[arg2],
AllowedFilters=[arg3] .
Informational
FQXSPEM4009I The UEFI Definitions have been changed. Informational
Chapter 2.XClarity Controller events 9

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPEM4010I UEFI Reported: [arg1]. Informational
FQXSPEM4011I XCC failed to log previo s event [arg1]. Informational
FQXSPEM4012I User [arg1] made system [arg2] Encaps lation lite Mode. Informational
FQXSPEM4013I Battery error was detected by RAID controller. The battery nit needs
replacement.([arg1],[arg2],[arg3],[arg4],[arg5])
Informational
FQXSPEM4014I The RAID controller has problem with the battery. Please contact
technical s pport to resolve this iss e.([arg1],[arg2],[arg3],[arg4],
[arg5])
Informational
FQXSPEM4015I The RAID controller detected nrecoverable error. The controller
needs replacement.([arg1],[arg2],[arg3],[arg4],[arg5])
Informational
FQXSPEM4016I The RAID controller detected one or more problems. Please contact
technical s pport for additional assistance.([arg1],[arg2],[arg3],[arg4],
[arg5])
Informational
FQXSPEM4017I The RAID controller detected one or more possible config ration
changes within the s bsystem. Please check the drive LED stat s. If
necessary, contact technical s pport for additional assistance.([arg1],
[arg2],[arg3],[arg4],[arg5])
Informational
FQXSPEM4018I Enclos re/Chassis iss e detected with one or more nits. Please
check the enclos re/chassis nits to repair the problem.([arg1],[arg2],
[arg3],[arg4],[arg5])
Informational
FQXSPEM4019I Connectivity iss e detected with the enclos re/chassis. Please check
yo r cable config rations to repair the problem.([arg1],[arg2],[arg3],
[arg4],[arg5])
Informational
FQXSPEM4020I Fan problem detected with the enclos re/chassis. Please check the
enclos re/chassis nit fan for correct operation.([arg1],[arg2],[arg3],
[arg4],[arg5])
Informational
FQXSPEM4022I Enclos re/Chassis power s pply has problem. Please check the
enclos re/chassis nit power s pply for correct operation.([arg1],
[arg2],[arg3],[arg4],[arg5])
Informational
FQXSPEM4023I One or more virt al drive are in abnormal stat s that may ca se
navailable virt al drive. Please check the event logs and if events are
targeted to the same disk then replace the drive. If necessary, contact
technical s pport for additional assistance.([arg1],[arg2],[arg3],[arg4],
[arg5])
Informational
FQXSPEM4024I The RAID controller detected one or more possible config ration
problem within the s bsystem. Please check the event logs and if
events are targeted to the same disk then replace the drive. If
necessary, contact technical s pport for additional assistance.([arg1],
[arg2],[arg3],[arg4],[arg5])
Informational
FQXSPEM4025I One or more virt al drive have problem. Please contact technical
s pport to resolve this iss e.([arg1],[arg2],[arg3],[arg4],[arg5])
Informational
FQXSPEM4026I Drive error was detected by RAID controller. Please contact technical
s pport to resolve this iss e.([arg1],[arg2],[arg3],[arg4],[arg5])
Informational
10 ThinkSystem SR250 V3 Messages and Codes Reference

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPEM4027I Drive error was detected by RAID controller. Please check the event
logs and if events are targeted to the same disk then replace the drive.
If necessary, contact technical s pport for additional assistance.
([arg1],[arg2],[arg3],[arg4],[arg5])
Informational
FQXSPEM4028I The port [arg1] of PCIe device [arg2] at [arg3] has link [arg4]. Informational
FQXSPEM4029I All PCIe slots on [arg1] may not be f nctional based pon yo r c rrent
CPU pop lation.
Informational
FQXSPEM4030I A sched led operation on the RAID controller has enco ntered an
iss e. Refer to RAID Logs nder Server Management, Local Storage,
for details.([arg1],[arg2],[arg3],[arg4],[arg5])
Informational
FQXSPEM4031I SSD wear threshold setting is changed from [arg1] to [arg2] by ser
[arg3] from [arg4] at IP address [arg5].
Informational
FQXSPEM4032I Aco stic Mode [arg1] has been engaged. Fan speed limits are in
place.
Informational
FQXSPEM4033I Aco stic Mode [arg1] has been disengaged to allow adeq ate
cooling.
Informational
FQXSPFC4000I The bare metal connection process has been started. Informational
FQXSPFC4001I The bare metal pdate application reports a stat s of [arg1]. Informational
FQXSPFC4002I System r nning in set p. Informational
FQXSPFC4003I UEFI deployment boot mode is enabled for NextBoot. Informational
FQXSPFC4004I UEFI deployment boot mode is enabled for NextAc. Informational
FQXSPFC4005I UEFI deployment boot mode has been disabled. Informational
FQXSPFW0003I The System [Comp terSystemElementName] enco ntered firmware
progress.
Informational
FQXSPIO0000I The connector [PhysicalConnectorElementName] has been
connected.
Informational
FQXSPIO0010I A Correctable B s Error has occ rred on b s [SensorElementName]. Informational
FQXSPIO2001I The connector [PhysicalConnectorElementName] config ration error
has been repaired.
Informational
FQXSPIO2003I System [Comp terSystemElementName] has recovered from a
diagnostic interr pt.
Informational
FQXSPIO2004I B s [SensorElementName] has recovered from a b s timeo t. Informational
FQXSPIO2006I System [Comp terSystemElementName] has recovered from an NMI. Informational
FQXSPIO2007I A PCI PERR recovery has occ rred on system
[Comp terSystemElementName].
Informational
FQXSPIO2008I A PCI SERR on system [Comp terSystemElementName] has
deasserted.
Informational
FQXSPIO2010I B s [SensorElementName] has recovered from a Correctable B s
Error.
Informational
FQXSPIO4002I GPU Board Stat s was recovered by [arg1] of [arg1]. Informational
Chapter 2.XClarity Controller events 11

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPMA0001I Error Detected and Corrected for [PhysicalMemoryElementName] on
S bsystem [MemoryElementName].
Informational
FQXSPMA0022I Post Package Repair S ccess for [PhysicalMemoryElementName] on
S bsystem [MemoryElementName].
Informational
FQXSPMA0023I Post Package Repair Fail re for [PhysicalMemoryElementName] on
S bsystem [MemoryElementName].
Informational
FQXSPMA0025I Sensor [SensorElementName] has asserted. Informational
FQXSPMA2007I Scr b Fail re for [PhysicalMemoryElementName] on S bsystem
[MemoryElementName] has recovered.
Informational
FQXSPMA2010I [PhysicalMemoryElementName] on S bsystem
[MemoryElementName] is no longer Throttled.
Informational
FQXSPMA2012I An Over-Temperat re Condition has been removed on the
[PhysicalMemoryElementName] on S bsystem
[MemoryElementName].
Informational
FQXSPMA2024I Sensor [SensorElementName] has deasserted. Informational
FQXSPNM4000I Management Controller [arg1] Network Initialization Complete. Informational
FQXSPNM4001I Ethernet Data Rate modified from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4002I Ethernet D plex setting modified from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4003I Ethernet MTU setting modified from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4004I Ethernet locally administered MAC address modified from [arg1] to
[arg2] by ser [arg3].
Informational
FQXSPNM4005I Ethernet interface [arg1] by ser [arg2]. Informational
FQXSPNM4006I Hostname set to [arg1] by ser [arg2]. Informational
FQXSPNM4007I IP address of network interface modified from [arg1] to [arg2] by ser
[arg3].
Informational
FQXSPNM4008I IP s bnet mask of network interface modified from [arg1] to [arg2] by
ser [arg3].
Informational
FQXSPNM4009I IP address of defa lt gateway modified from [arg1] to [arg2] by ser
[arg3].
Informational
FQXSPNM4011I ENET[[arg1]] DHCP-HSTN=[arg2], DN=[arg3], IP@=[arg4], SN=[arg5],
GW@=[arg6], DNS1@=[arg7] .
Informational
FQXSPNM4012I ENET[[arg1]] IP-Cfg:HstName=[arg2], IP@=[arg3] ,NetMsk=[arg4],
GW@=[arg5] .
Informational
FQXSPNM4013I LAN: Ethernet[[arg1]] interface is no longer active. Informational
FQXSPNM4014I LAN: Ethernet[[arg1]] interface is now active. Informational
FQXSPNM4015I DHCP setting changed to [arg1] by ser [arg2]. Informational
FQXSPNM4016I Domain name set to [arg1] by ser [arg2]. Informational
FQXSPNM4017I Domain So rce changed to [arg1] by ser [arg2]. Informational
FQXSPNM4018I DDNS setting changed to [arg1] by ser [arg2]. Informational
12 ThinkSystem SR250 V3 Messages and Codes Reference

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPNM4019I DDNS registration s ccessf l. The domain name is [arg1]. Informational
FQXSPNM4020I IPv6 enabled by ser [arg1] . Informational
FQXSPNM4021I IPv6 disabled by ser [arg1] . Informational
FQXSPNM4022I IPv6 static IP config ration enabled by ser [arg1]. Informational
FQXSPNM4023I IPv6 DHCP enabled by ser [arg1]. Informational
FQXSPNM4024I IPv6 stateless a to-config ration enabled by ser [arg1]. Informational
FQXSPNM4025I IPv6 static IP config ration disabled by ser [arg1]. Informational
FQXSPNM4026I IPv6 DHCP disabled by ser [arg1]. Informational
FQXSPNM4027I IPv6 stateless a to-config ration disabled by ser [arg1]. Informational
FQXSPNM4028I ENET[[arg1]] IPv6-LinkLocal:HstName=[arg2], IP@=[arg3] ,Pref=[arg4]
.
Informational
FQXSPNM4029I ENET[[arg1]] IPv6-Static:HstName=[arg2], IP@=[arg3] ,Pref=[arg4],
GW@=[arg5] .
Informational
FQXSPNM4030I ENET[[arg1]] DHCPv6-HSTN=[arg2], DN=[arg3], IP@=[arg4], Pref=
[arg5], DNS1@=[arg5].
Informational
FQXSPNM4031I IPv6 static address of network interface modified from [arg1] to [arg2]
by ser [arg3].
Informational
FQXSPNM4033I Telnet port n mber changed from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4034I SSH port n mber changed from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4035I Web-HTTP port n mber changed from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4036I Web-HTTPS port n mber changed from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4037I CIM/XML HTTP port n mber changed from [arg1] to [arg2] by ser
[arg3].
Informational
FQXSPNM4038I CIM/XML HTTPS port n mber changed from [arg1] to [arg2] by ser
[arg3].
Informational
FQXSPNM4039I SNMP Agent port n mber changed from [arg1] to [arg2] by ser
[arg3].
Informational
FQXSPNM4040I SNMP Traps port n mber changed from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4041I Syslog port n mber changed from [arg1] to [arg2] by ser [arg3]. Informational
FQXSPNM4042I Remote Presence port n mber changed from [arg1] to [arg2] by ser
[arg3].
Informational
FQXSPNM4043I SMTP Server set by ser [arg1] to [arg2]:[arg3]. Informational
FQXSPNM4044I Telnet [arg1] by ser [arg2]. Informational
FQXSPNM4045I DNS servers set by ser [arg1]: UseAdditionalServers=[arg2],
PreferredDNStype=[arg3], IPv4Server1=[arg4], IPv4Server2=[arg5],
IPv4Server3=[arg6], IPv6Server1=[arg7], IPv6Server2=[arg8],
IPv6Server3=[arg9].
Informational
FQXSPNM4046I LAN over USB [arg1] by ser [arg2]. Informational
Chapter 2.XClarity Controller events 13

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPNM4047I LAN over USB Port Forwarding set by ser [arg1]: ExternalPort=
[arg2], USB-LAN port=[arg3].
Informational
FQXSPNM4048I PXE boot req ested by ser [arg1]. Informational
FQXSPNM4049I User [arg1] has initiated a TKLM Server Connection Test to check
connectivity to server [arg2].
Informational
FQXSPNM4050I User [arg1] has initiated an SMTP Server Connection Test. Informational
FQXSPNM4051I User [arg1] has set the SMTP Server reverse-path to [arg2]. Informational
FQXSPNM4052I DHCP specified hostname is set to [arg1] by ser [arg2]. Informational
FQXSPNM4053I DNS discovery of Lenovo XClarity Administrator has been [arg1] by
ser [arg2].
Informational
FQXSPNM4054I The hostname from DHCP is [arg1] by ser [arg2]. Informational
FQXSPNM4055I The hostname from DHCP is invalid. Informational
FQXSPNM4056I The NTP server address [arg1] is invalid. Informational
FQXSPNM4057I Sec rity: IP address: [arg1] had [arg2] login fail res, it will be blocked
to access for [arg3] min tes.
Informational
FQXSPNM4058I IP address of network interface [arg1] is modified from [arg2] to [arg3]
by ser [arg4].
Informational
FQXSPNM4059I IP s bnet mask of network interface [arg1] is modified from [arg2] to
[arg3] by ser [arg4].
Informational
FQXSPNM4060I IP address of defa lt gateway of network interface [arg1] is modified
from [arg2] to [arg3] by ser [arg4].
Informational
FQXSPOS4000I OS Watchdog response [arg1] by [arg2] . Informational
FQXSPOS4001I Watchdog [arg1] Screen Capt re Occ rred . Informational
FQXSPOS4004I Operating System stat s has changed to [arg1]. Informational
FQXSPOS4005I Host Power-On password changed by ser [arg1] from [arg2] at IP
address [arg3].
Informational
FQXSPOS4006I Host Power-On password cleared by ser [arg1] from [arg2] at IP
address [arg3].
Informational
FQXSPOS4007I Host Admin password changed by ser [arg1] from [arg2] at IP
address [arg3].
Informational
FQXSPOS4008I Host Admin password cleared by ser [arg1] from [arg2] at IP address
[arg3].
Informational
FQXSPOS4009I OS Crash Video Capt red. Informational
FQXSPOS4011I OS fail re screen capt re with hardware error is [arg1] by ser [arg2]
from [arg3] at IP address [arg4].
Informational
FQXSPPP4000I Attempting to [arg1] server [arg2] by ser [arg3]. Informational
FQXSPPP4001I Server Power Off Delay set to [arg1] by ser [arg2]. Informational
FQXSPPP4002I Server [arg1] sched led for [arg2] at [arg3] by ser [arg4]. Informational
14 ThinkSystem SR250 V3 Messages and Codes Reference

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPPP4003I Server [arg1] sched led for every [arg2] at [arg3] by ser [arg4]. Informational
FQXSPPP4004I Server [arg1] [arg2] cleared by ser [arg3]. Informational
FQXSPPP4005I The power cap val e changed from [arg1] watts to [arg2] watts by
ser [arg3].
Informational
FQXSPPP4006I The minim m power cap val e changed from [arg1] watts to [arg2]
watts.
Informational
FQXSPPP4007I The maxim m power cap val e changed from [arg1] watts to [arg2]
watts.
Informational
FQXSPPP4008I The soft minim m power cap val e changed from [arg1] watts to
[arg2] watts.
Informational
FQXSPPP4011I Power capping was activated by ser [arg1]. Informational
FQXSPPP4012I Power capping was deactivated by ser [arg1]. Informational
FQXSPPP4013I Static Power Savings mode has been t rned on by ser [arg1]. Informational
FQXSPPP4014I Static Power Savings mode has been t rned off by ser [arg1]. Informational
FQXSPPP4015I Dynamic Power Savings mode has been t rned on by ser [arg1]. Informational
FQXSPPP4016I Dynamic Power Savings mode has been t rned off by ser [arg1]. Informational
FQXSPPP4017I Power cap and external throttling occ rred. Informational
FQXSPPP4018I External throttling occ rred . Informational
FQXSPPP4019I Power cap throttling occ rred. Informational
FQXSPPP4020I The meas red power val e has ret rned below the power cap val e. Informational
FQXSPPP4021I The new minim m power cap val e has ret rned below the power cap
val e.
Informational
FQXSPPP4022I The server was restarted for an nknown reason. Informational
FQXSPPP4023I The server is restarted by chassis control command. Informational
FQXSPPP4024I The server was reset via p sh b tton. Informational
FQXSPPP4025I The server was powered- p via power p sh b tton. Informational
FQXSPPP4026I The server was restarted when the watchdog expired.. Informational
FQXSPPP4027I The server was restarted for OEM reason. Informational
FQXSPPP4028I The server was a tomatically powered on beca se the power restore
policy is set to always restore..
Informational
FQXSPPP4029I The server was a tomatically powered on beca se the power restore
policy is set to restore previo s power state..
Informational
FQXSPPP4030I The server was reset via Platform Event Filter. Informational
FQXSPPP4031I The server was power-cycled via Platform Event Filter. Informational
FQXSPPP4032I The server was soft reset. Informational
FQXSPPP4033I The server was powered p via Real Time Clock (sched led power
on).
Informational
Chapter 2.XClarity Controller events 15

Table 2. E ents organized by se erity (continued)
E ent ID Message String Se erity
FQXSPPP4034I The server was powered off for an nknown reason. Informational
FQXSPPP4035I The server was powered off by chassis control command. Informational
FQXSPPP4036I The server was powered off via p sh b tton. Informational
FQXSPPP4037I The server was powered off when the watchdog expired. Informational
FQXSPPP4038I The server stayed powered off beca se the power restore policy is set
to always restore..
Informational
FQXSPPP4039I The server stayed powered off beca se the power restore policy is set
to restore previo s power state..
Informational
FQXSPPP4040I The server was powered off via Platform Event Filter. Informational
FQXSPPP4041I The server was powered off via Real Time Clock (sched led power
off).
Informational
FQXSPPP4042I Management Controller [arg1] reset was initiated d e to Power-On-
Reset.
Informational
FQXSPPP4043I Management Controller [arg1] reset was initiated by PRESET. Informational
FQXSPPP4044I Management Controller [arg1] reset was initiated by CMM. Informational
FQXSPPP4045I Management Controller [arg1] reset was initiated by XCC firmware. Informational
FQXSPPP4046I Remote power permission is [arg1]. Informational
FQXSPPP4047I Management Controller [arg1] reset was initiated by ser [arg2]. Informational
FQXSPPP4048I Attempting to AC power cycle server [arg1] by ser [arg2]. Informational
FQXSPPP4049I Management Controller [arg1] reset was initiated by Front Panel. Informational
FQXSPPP4050I Management Controller [arg1] reset was initiated to activate PFR
Firmware.
Informational
FQXSPPU0000I [ProcessorElementName] in slot [SlotElementName] has been added. Informational
FQXSPPU2000I [ProcessorElementName] in slot [SlotElementName] has been
removed.
Informational
FQXSPPU2001I An Over-Temperat re Condition has been removed on
[ProcessorElementName].
Informational
FQXSPPU2002I The Processor [ProcessorElementName] is no longer operating in a
Degraded State.
Informational
FQXSPPW0001I [PowerS pplyElementName] has been added to container
[PhysicalPackageElementName].
Informational
FQXSPPW0005I [PowerS pplyElementName] is operating in an Inp t State that is o t
of range.
Informational
FQXSPPW0008I [SensorElementName] has been t rned off. Informational
FQXSPPW0009I [PowerS pplyElementName] has been Power Cycled. Informational
FQXSPPW2001I [PowerS pplyElementName] has been removed from container
[PhysicalPackageElementName].
Informational
FQXSPPW2002I [PowerS pplyElementName] has ret rned to OK stat s. Informational
16 ThinkSystem SR250 V3 Messages and Codes Reference